Download Analog Devices Welcomes Hittite Microwave Corporation

Survey
yes no Was this document useful for you?
   Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Document related concepts

Audio power wikipedia , lookup

Spark-gap transmitter wikipedia , lookup

History of electric power transmission wikipedia , lookup

Tube sound wikipedia , lookup

Pulse-width modulation wikipedia , lookup

Electrical substation wikipedia , lookup

Electrical ballast wikipedia , lookup

Heterodyne wikipedia , lookup

Ground (electricity) wikipedia , lookup

Power inverter wikipedia , lookup

Ohm's law wikipedia , lookup

Immunity-aware programming wikipedia , lookup

Current source wikipedia , lookup

Variable-frequency drive wikipedia , lookup

Ground loop (electricity) wikipedia , lookup

Islanding wikipedia , lookup

Power MOSFET wikipedia , lookup

Triode wikipedia , lookup

Integrating ADC wikipedia , lookup

Wien bridge oscillator wikipedia , lookup

Rectifier wikipedia , lookup

Three-phase electric power wikipedia , lookup

Surge protector wikipedia , lookup

Power electronics wikipedia , lookup

Schmitt trigger wikipedia , lookup

Voltage regulator wikipedia , lookup

Stray voltage wikipedia , lookup

Buck converter wikipedia , lookup

Alternating current wikipedia , lookup

Resistive opto-isolator wikipedia , lookup

Switched-mode power supply wikipedia , lookup

Voltage optimisation wikipedia , lookup

Opto-isolator wikipedia , lookup

Mains electricity wikipedia , lookup

Transcript
Analog Devices Welcomes
Hittite Microwave Corporation
NO CONTENT ON THE ATTACHED DOCUMENT HAS CHANGED
www.analog.com
www.hittite.com
THIS PAGE INTENTIONALLY LEFT BLANK
HMC431LP4 / 431LP4E
v04.1106
MMIC VCO w/ BUFFER
AMPLIFIER, 5.5 - 6.1 GHz
Typical Applications
Features
Low noise MMIC VCO w/Buffer Amplifier
for C-Band applications such as:
Pout: +2 dBm
• 802.11a & HiperLAN WLAN
No External Resonator Needed
• VSAT Radios
Single Supply: 3V @ 27 mA
• UNII & Point-to-Point Radios
16mm2 Leadless SMT Package
Functional Diagram
General Description
Phase Noise: -102 dBc/Hz @100 kHz
The HMC431LP4 & HMC431LP4E are GaAs InGaP
Heterojunction Bipolar Transistor (HBT) MMIC VCOs
with integrated resonators, negative resistance
devices, varactor diodes, and buffer amplifiers. The
VCO’s phase noise performance is excellent over
temperature, shock, vibration and process due to the
oscillator’s monolithic structure. Power output is 2
dBm typical from a 3V supply voltage. The voltage
controlled oscillator is packaged in a low cost leadless
QFN 4 x 4 mm surface mount package.
VCOS & PLOs - SMT
11
Electrical Specifi cations, TA = +25° C, Vcc = +3V
Parameter
Min.
Frequency Range
Power Output
-1
SSB Phase Noise @ 100 kHz Offset, Vtune= +5V @ RF Output
Tune Voltage (Vtune)
Supply Current (Icc) (Vcc= 3.0V)
Typ.
GHz
dBm
-102
0
dBc/Hz
10
27
V
mA
10
μA
6
dB
-15
-30
dBc
dBc
Pulling (into a 2.0:1 VSWR)
9
MHz pp
Pushing @ Vtune= +5V
12
MHz/V
Frequency Drift Rate
0.8
MHz/°C
Harmonics
2nd
3rd
11 - 84
Units
2
Tune Port Leakage Current
Output Return Loss
Max.
5.5 - 6.1
For price, delivery, and to place orders, please contact Hittite Microwave Corporation:
20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373
Order On-line at www.hittite.com
HMC431LP4 / 431LP4E
v04.1106
MMIC VCO w/ BUFFER
AMPLIFIER, 5.5 - 6.1 GHz
Frequency vs. Tuning Voltage, Vcc= +3V
6.6
6.6
6.4
6.4
OUTPUT FREQUENCY (GHz)
6.2
6
5.8
5.6
5.4
Vcc= 2.75V
Vcc= 3.0V
Vcc= 3.25V
5.2
5
6.2
6
5.8
5.6
5.4
+25 C
+85 C
-40 C
5.2
5
4.8
4.8
0
1
2
3
4
5
6
7
8
9
10
0
1
2
TUNING VOLTAGE (VOLTS)
500
10
450
8
400
6
350
+25 C
+85 C
-40 C
250
200
150
100
4
5
6
7
-4
9
10
8
9
11
+25 C
+85 C
-40 C
-6
0
10
TUNING VOLTAGE (VOLTS)
1
2
3
4
5
6
7
8
9
10
TUNING VOLTAGE (VOLTS)
Phase Noise vs. Tuning Voltage
Typical SSB Phase Noise @ Vtune= +5V
-70
0
-75
SSB PHASE NOISE (dBc/Hz)
SSB PHASE NOISE (dBc/Hz)
8
0
-8
3
7
-2
-10
2
6
2
0
1
5
4
50
0
4
Output Power vs.
Tuning Voltage, Vcc= +3V
OUTPUT POWER (dBm)
SENSITIVITY (MHz/VOLT)
Sensitivity vs. Tuning Voltage, Vcc= +3V
300
3
TUNING VOLTAGE (VOLTS)
VCOS & PLOs - SMT
OUTPUT FREQUENCY (GHz)
Frequency vs. Tuning Voltage, T= 25°C
-80
-85
-90
10kHz offset
100kHz offset
-95
-100
-105
-110
0
1
2
3
4
5
6
7
TUNING VOLTAGE (VOLTS)
8
9
10
-25
+25 C
+85 C
-40 C
-50
-75
-100
-125
-150
3
10
4
10
5
10
6
10
7
10
OFFSET FREQUENCY (Hz)
For price, delivery, and to place orders, please contact Hittite Microwave Corporation:
20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373
Order On-line at www.hittite.com
11 - 85
HMC431LP4 / 431LP4E
v04.1106
MMIC VCO w/ BUFFER
AMPLIFIER, 5.5 - 6.1 GHz
Absolute Maximum Ratings
Vcc
+3.5 Vdc
Vcc (V)
Vtune
0 to +11V
2.75
Icc (mA)
19
Channel Temperature
135 °C
3.0
27
Continuous Pdiss (T = 85°C)
(derate 6.28 mW/°C above 85°C)
565 W
3.25
34
Storage Temperature
-65 to +150 °C
Operating Temperature
-40 to +85 °C
ESD Sensitivity (HBM)
Class 1A
Note: VCO will operate over full voltage range shown above.
ELECTROSTATIC SENSITIVE DEVICE
OBSERVE HANDLING PRECAUTIONS
Outline Drawing
VCOS & PLOs - SMT
11
Typical Supply Current vs. Vcc
NOTES:
1. LEADFRAME MATERIAL: COPPER ALLOY
2. DIMENSIONS ARE IN INCHES [MILLIMETERS]
3. LEAD SPACING TOLERANCE IS NON-CUMULATIVE.
4. PAD BURR LENGTH SHALL BE 0.15mm MAXIMUM.
PAD BURR HEIGHT SHALL BE 0.05mm MAXIMUM.
5. PACKAGE WARP SHALL NOT EXCEED 0.05mm.
6. ALL GROUND LEADS AND GROUND PADDLE MUST BE
SOLDERED TO PCB RF GROUND.
7. REFER TO HITTITE APPLICATION NOT FOR SUGGESTED
LAND PATTERN.
Package Information
Part Number
Package Body Material
Lead Finish
MSL Rating
HMC431LP4
Low Stress Injection Molded Plastic
Sn/Pb Solder
MSL1
HMC431LP4E
RoHS-compliant Low Stress Injection Molded Plastic
100% matte Sn
MSL1
Package Marking [3]
[1]
H431
XXXX
[2]
H431
XXXX
[1] Max peak reflow temperature of 235 °C
[2] Max peak reflow temperature of 260 °C
[3] 4-Digit lot number XXXX
11 - 86
For price, delivery, and to place orders, please contact Hittite Microwave Corporation:
20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373
Order On-line at www.hittite.com
HMC431LP4 / 431LP4E
v04.1106
MMIC VCO w/ BUFFER
AMPLIFIER, 5.5 - 6.1 GHz
Pin Descriptions
Function
Description
1 - 14, 17 - 19,
21, 23, 24
N/C
No Connection
15
GND
This pin must be connected to RF & DC ground.
16
RFOUT
RF output (AC coupled)
20
Vcc
Supply Voltage Vcc= 3V
22
VTUNE
Control Voltage Input. Modulation port bandwidth
dependent on drive source impedance.
GND
Package bottom has an exposed metal paddle that
must be RF & DC grounded.
Interface Schematic
For price, delivery, and to place orders, please contact Hittite Microwave Corporation:
20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373
Order On-line at www.hittite.com
11
VCOS & PLOs - SMT
Pin Number
11 - 87
HMC431LP4 / 431LP4E
v04.1106
MMIC VCO w/ BUFFER
AMPLIFIER, 5.5 - 6.1 GHz
Evaluation PCB
VCOS & PLOs - SMT
11
List of Materials for Evaluation PCB 105706 [1]
Item
Description
J1 - J2
PCB Mount SMA RF Connector
J3 - J4
DC Pin
C1
4.7 μF Tantalum Capacitor
C2
10,000 pF Capacitor, 0603 Pkg.
U1
HMC431LP4 / HMC431LP4E VCO
PCB [2]
105667 Eval Board
[1] Reference this number when ordering complete evaluation PCB
[2] Circuit Board Material: Rogers 4350
11 - 88
The circuit board used in the final application should
use RF circuit design techniques. Signal lines
should have 50 ohm impedance while the package
ground leads and exposed paddle should be connected directly to the ground plane similar to that
shown. A sufficient number of via holes should be
used to connect the top and bottom ground planes.
The evaluation circuit board shown is available from
Hittite upon request.
For price, delivery, and to place orders, please contact Hittite Microwave Corporation:
20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373
Order On-line at www.hittite.com
HMC431LP4 / 431LP4E
v04.1106
MMIC VCO w/ BUFFER
AMPLIFIER, 5.5 - 6.1 GHz
Notes:
VCOS & PLOs - SMT
11
For price, delivery, and to place orders, please contact Hittite Microwave Corporation:
20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373
Order On-line at www.hittite.com
11 - 89