* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Download EET 221/3 - UniMAP Portal
History of electric power transmission wikipedia , lookup
Flexible electronics wikipedia , lookup
Audio power wikipedia , lookup
Chirp compression wikipedia , lookup
Spark-gap transmitter wikipedia , lookup
Electronic engineering wikipedia , lookup
Power engineering wikipedia , lookup
Chirp spectrum wikipedia , lookup
Solar micro-inverter wikipedia , lookup
Utility frequency wikipedia , lookup
Voltage optimisation wikipedia , lookup
Electrical substation wikipedia , lookup
Oscilloscope history wikipedia , lookup
Wien bridge oscillator wikipedia , lookup
Alternating current wikipedia , lookup
Variable-frequency drive wikipedia , lookup
Distribution management system wikipedia , lookup
Two-port network wikipedia , lookup
Resistive opto-isolator wikipedia , lookup
Mains electricity wikipedia , lookup
Regenerative circuit wikipedia , lookup
Power inverter wikipedia , lookup
Opto-isolator wikipedia , lookup
Buck converter wikipedia , lookup
Switched-mode power supply wikipedia , lookup
Power Electronics for Energy System (EET424) Laboratory Module EXPERIMENT 6 Pulse Width Modulation (PWM) Circuits for Inverters (Part 2) Another method that we are going to learn in this experiment is the single-pulse width modulation technique. This method is much easier to be made and the circuit is less complex compares to the sinusoidal PWM technique. The modulated wave is a squarewave of low frequency (may be 50Hz or 60Hz) and envelopes the high frequency switching pulses. The effective power to the load can be controlled by varying the duty cycle of the high frequency pulses. Fig 2.0 below shows the block concept of producing the output waveform. Fig 2.0 : Single- PWM concept 1) Open a new document on the PSIM. Draw the circuit as shown in Fig 2.1 below. Fig 2.1 : Single-PWM circuit 2) Set the parameters of VSQ1 as : UNIVERSITI MALAYSIA PERLIS – Exp.6 (Revision 2) 1 Power Electronics for Energy System (EET424) Laboratory Module Name : VSQ1 Vpeak_peak : 5 Frequency : 50 Duty Cycle : 0.5 DC Offset : 0 3) Similarly, set the parameters of VSQ2 as : Name : VSQ2 Vpeak_peak : 2 Frequency :1k Duty Cycle : 0.5 DC Offset : 0 4) After you have completed the circuit, set the simulation control time to : Time step is 10m and Total time is 0.03. 5) Run the program. Then click Simview to observe the respective waveforms. Inside the Data Selection box, click VSQ1 and VSQ2 together and press Add. Then press OK and both of the waveforms will appear on the screen. 6) Then click the Add Screen button at the top menu and another selection will be displayed. Now choose Vs1,s2 and Vs3,s4 together and press Add. A new screen with the waveforms should appear. 7) Neatly draw all of the waveforms on a graph paper and clearly labels them. (5x2m) 8) Save the schematic circuit into your pen-drive. You will need to copy the circuit into your next week’s lab. 9) The effective power to the load can be controlled by varying the duty cycle of the switching frequency. Design a simple circuit using PSIM to give a single output of pulses that the width can be controlled accordingly. Then simulate it to prove that your circuit works well. (Hint : refer to certain section of the circuit in Fig 1.1 (Exp.5) and use DC voltage source). Draw your designed circuit. (5m) 10) Run your circuit and draw the related waveforms to show the output pulses width changes as you use 5 different DC voltage levels (at 0.3V, 1.5V, 4.0V, 6.5V and 7.0V). (Draw the output pulse for each condition between 10ms – 13ms). (4x5m) 11) Determine the width of each pulse (in ms) at different DC voltage levels (VDC1) and fill in as in the table below. VDC1 0.3V 1.5V 4.0V 6.5V 7.0V Pulse width (ms) (5m) UNIVERSITI MALAYSIA PERLIS – Exp.6 (Revision 2) 2 Power Electronics for Energy System (EET424) Laboratory Module 12) Plot a graph of Pulse width agaist VDC1. (4m) 13) From the graph, determine the VDC1 that needs to produce a pulse width output of 0.8ms. (2m) 14) Change VDC1 to 8.0V and observe the output. Is it zero or not ? Please explain why the condition is as such. (2+3m) 15) What is the actual limit voltage that VDC1 needs to be set in order to get the output to be zero ? 16) Please state your conclusion for the whole of this experiment. (2m) (3m) (Total=56m) UNIVERSITI MALAYSIA PERLIS – Exp.6 (Revision 2) 3