
Functional Testing
... signals may simply remain unchanged at a 1 or 0 level during a cycle, they may change once during the cycle, or they may be required to pulse to a valid logic state for a specified period of time. The signal formats below enable the proper signal generation required to correctly control any digital ...
... signals may simply remain unchanged at a 1 or 0 level during a cycle, they may change once during the cycle, or they may be required to pulse to a valid logic state for a specified period of time. The signal formats below enable the proper signal generation required to correctly control any digital ...
Investigation Of Factors Affecting The Sustainability Of Arcs
... This exception does not direct workers to wear arc rated PPE for protection. It implies that there is no arc flash hazard because arc faults would either self-extinguish on such circuits or have insufficient incident energy to cause burns or ignite clothing. Note also that NFPA70E includes circuits ...
... This exception does not direct workers to wear arc rated PPE for protection. It implies that there is no arc flash hazard because arc faults would either self-extinguish on such circuits or have insufficient incident energy to cause burns or ignite clothing. Note also that NFPA70E includes circuits ...
PXIe-4302/4303 RM-4302 User Guide and RM
... This product was tested and complies with the regulatory requirements and limits for electromagnetic compatibility (EMC) stated in the product specifications. These requirements and limits provide reasonable protection against harmful interference when the product is operated in the intended operati ...
... This product was tested and complies with the regulatory requirements and limits for electromagnetic compatibility (EMC) stated in the product specifications. These requirements and limits provide reasonable protection against harmful interference when the product is operated in the intended operati ...
ADDC02808PB 28 V, 200 W Pulsed DC/DC Converter with Integral
... available to synchronize multiple units to one switching frequency. This feature is particularly useful in eliminating beat frequencies which may cause increased output ripple on paralleled units. A current share pin (ISHARE) is available which permits paralleled units to share current typically wit ...
... available to synchronize multiple units to one switching frequency. This feature is particularly useful in eliminating beat frequencies which may cause increased output ripple on paralleled units. A current share pin (ISHARE) is available which permits paralleled units to share current typically wit ...
AN109 - Interfacing RF I/Q Modulators with Popular D/A Converters
... LT1565-31 is set by applying a DC voltage at Pin 3. See Figure 10 for details. Noise may also be an issue with the use of active devices in the baseband circuit. Any active device will have an output noise level that is higher than that of a passive circuit. Take Figure 10 showing the circuit coupli ...
... LT1565-31 is set by applying a DC voltage at Pin 3. See Figure 10 for details. Noise may also be an issue with the use of active devices in the baseband circuit. Any active device will have an output noise level that is higher than that of a passive circuit. Take Figure 10 showing the circuit coupli ...
NTP75N03L09, NTB75N03L09 Power MOSFET 75 Amps
... “Typical” parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. ...
... “Typical” parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. ...
Optional Standby Systems - Adams Electric Cooperative
... Use of portable generators is classified into two types of systems — separately derived system and nonseparately derived system. A separately derived system is defined by the Code as: A premises wiring system whose power is derived from a source of electric energy or equipment other than a service. ...
... Use of portable generators is classified into two types of systems — separately derived system and nonseparately derived system. A separately derived system is defined by the Code as: A premises wiring system whose power is derived from a source of electric energy or equipment other than a service. ...
Non-electrical equipment.
... cold water pipe near the equipment if the extension was installed before August 13, 2007. Note: When any element of this branch circuit is replaced, the entire branch circuit shall use an equipment grounding conductor that complies with all other provisions of paragraph 304(g). ...
... cold water pipe near the equipment if the extension was installed before August 13, 2007. Note: When any element of this branch circuit is replaced, the entire branch circuit shall use an equipment grounding conductor that complies with all other provisions of paragraph 304(g). ...
Guidelines for the Design, Installation, Operation
... If wires are accessible to wildlife, they may damage the electrical insulation resulting in an exposed conductor. ...
... If wires are accessible to wildlife, they may damage the electrical insulation resulting in an exposed conductor. ...
PowerPoint 簡報
... c) Where a mains flexible cord is provided by the manufacturer this shall be 1m long,or if excess of 1m,the excess cable is folded back and forth as far as possible so as to form a bundle not exceeding 0.4m in length. d) Where a mains cable is specified in the manufacture’s installation instructions ...
... c) Where a mains flexible cord is provided by the manufacturer this shall be 1m long,or if excess of 1m,the excess cable is folded back and forth as far as possible so as to form a bundle not exceeding 0.4m in length. d) Where a mains cable is specified in the manufacture’s installation instructions ...
SURGELOGIC™ TVSS Surge Protective Devices
... • Thermal Fusing • 200kA Short Circuit Current Rating ...
... • Thermal Fusing • 200kA Short Circuit Current Rating ...
Electromagnetic compatibility

Electromagnetic compatibility (EMC) is the branch of electrical sciences which studies the unintentional generation, propagation and reception of electromagnetic energy with reference to the unwanted effects (electromagnetic interference, or EMI) that such energy may induce. The goal of EMC is the correct operation, in the same electromagnetic environment, of different equipment which use electromagnetic phenomena, and the avoidance of any interference effects.In order to achieve this, EMC pursues two different kinds of issues. Emission issues are related to the unwanted generation of electromagnetic energy by some source, and to the countermeasures which should be taken in order to reduce such generation and to avoid the escape of any remaining energies into the external environment. Susceptibility or immunity issues, in contrast, refer to the correct operation of electrical equipment, referred to as the victim, in the presence of unplanned electromagnetic disturbances.Interference mitigation and hence electromagnetic compatibility is achieved by addressing both emission and susceptibility issues, i.e., quieting the sources of interference and hardening the potential victims. The coupling path between source and victim may also be separately addressed to increase its attenuation.