Presentation
... basis for the generation of most of the electricity that is produced in the world today. Electromagnetic induction can also be used to change or transform an emf (a voltage). It is used in devices called transformers that increase or decrease the voltage, of an alternating current power supply. ...
... basis for the generation of most of the electricity that is produced in the world today. Electromagnetic induction can also be used to change or transform an emf (a voltage). It is used in devices called transformers that increase or decrease the voltage, of an alternating current power supply. ...
The high voltage (HV) pulse radiation of a discone antenna
... order of hundreds of kV and vary fast rise time , in the order of sub nano second. The paper deals through the response of the discone antenna to the above said pulse. The high voltage scenario with transformer oil medium is shown. Prior to the practical implementation, simulations were carried out ...
... order of hundreds of kV and vary fast rise time , in the order of sub nano second. The paper deals through the response of the discone antenna to the above said pulse. The high voltage scenario with transformer oil medium is shown. Prior to the practical implementation, simulations were carried out ...
proposal and modalities for combined geoscientist examination for
... (Instrumentation) and Mineral Physics to suit the redefined objectives under different missions and for better cadre management. HPC report has also taken into view of the emerging of integrated and multi disciplinary branches of earth sciences. To rationalize the system of recruitment for the post ...
... (Instrumentation) and Mineral Physics to suit the redefined objectives under different missions and for better cadre management. HPC report has also taken into view of the emerging of integrated and multi disciplinary branches of earth sciences. To rationalize the system of recruitment for the post ...
PS25451 EPIC QFN sensor, non-contact, high gain Datasheet
... Plessey Semiconductors Electric Potential Integrated Circuit (EPIC) product line targets a range of applications. The PS25451 is an ultra high impedance non-contact solid state electric potential sensor. It can be used to detect field disturbance due to the movement of a near-by object. This functio ...
... Plessey Semiconductors Electric Potential Integrated Circuit (EPIC) product line targets a range of applications. The PS25451 is an ultra high impedance non-contact solid state electric potential sensor. It can be used to detect field disturbance due to the movement of a near-by object. This functio ...
Dear Mr
... shown in the schematic S1 and S2. These shunts are connected to Armature winding of Drive motor where supply voltage is 750 V or 550 V DC depending on the usage. These are also used for excitation current measurements for generator under testing. The voltage available at shunt is of the order of 750 ...
... shown in the schematic S1 and S2. These shunts are connected to Armature winding of Drive motor where supply voltage is 750 V or 550 V DC depending on the usage. These are also used for excitation current measurements for generator under testing. The voltage available at shunt is of the order of 750 ...
Interconnection Application/Agreement - Part 1
... the proposed facility on the EDC’s electrical distribution system at the time of the initial application. Often times the equipment for which this information is needed hasn’t been specified. The type information necessary may be conveyed during a scoping meeting or other correspondence early on dur ...
... the proposed facility on the EDC’s electrical distribution system at the time of the initial application. Often times the equipment for which this information is needed hasn’t been specified. The type information necessary may be conveyed during a scoping meeting or other correspondence early on dur ...
Pulse Generator HM8035
... "WIDTH>PERIOD" indicator signals the operator that a nonrealizable ratio of pulse width to repetition rate has been entered. The output signal is available with either positive or negative polarity at two individual outputs, which are each independently adjustable from 0.8 to 5Vpp. Some applications ...
... "WIDTH>PERIOD" indicator signals the operator that a nonrealizable ratio of pulse width to repetition rate has been entered. The output signal is available with either positive or negative polarity at two individual outputs, which are each independently adjustable from 0.8 to 5Vpp. Some applications ...
2Pro AC Devices Provide Overcurrent Overvoltage
... current condition the unprotected MOV will first fall to low impedance of a few Ohms, but due to the high amount of energy it is likely to rupture rather than protect. If there are devices used on the AC line return path that limit current flow these may also overheat due to the failure of the MOV. ...
... current condition the unprotected MOV will first fall to low impedance of a few Ohms, but due to the high amount of energy it is likely to rupture rather than protect. If there are devices used on the AC line return path that limit current flow these may also overheat due to the failure of the MOV. ...
CLUSTER Engineering and Technical CONCENTRATION Industrial
... demonstrate how to connect a dual-voltage three-phase induction motor for operation, and reverse rotation. identify the types of electric motors commonly used in industrial applications. explain the purpose and application of an electrical coil. demonstrate the application of maintained and momentar ...
... demonstrate how to connect a dual-voltage three-phase induction motor for operation, and reverse rotation. identify the types of electric motors commonly used in industrial applications. explain the purpose and application of an electrical coil. demonstrate the application of maintained and momentar ...
Electromagnetic compatibility
Electromagnetic compatibility (EMC) is the branch of electrical sciences which studies the unintentional generation, propagation and reception of electromagnetic energy with reference to the unwanted effects (electromagnetic interference, or EMI) that such energy may induce. The goal of EMC is the correct operation, in the same electromagnetic environment, of different equipment which use electromagnetic phenomena, and the avoidance of any interference effects.In order to achieve this, EMC pursues two different kinds of issues. Emission issues are related to the unwanted generation of electromagnetic energy by some source, and to the countermeasures which should be taken in order to reduce such generation and to avoid the escape of any remaining energies into the external environment. Susceptibility or immunity issues, in contrast, refer to the correct operation of electrical equipment, referred to as the victim, in the presence of unplanned electromagnetic disturbances.Interference mitigation and hence electromagnetic compatibility is achieved by addressing both emission and susceptibility issues, i.e., quieting the sources of interference and hardening the potential victims. The coupling path between source and victim may also be separately addressed to increase its attenuation.