data sheet - Resistors
... environment of use. be takenoftouse. avoid potential sources of ionic contamination environment contacting the resistor body, for example, flux applied by Packaging spraying, encapsulation materials or contaminants from the Packaging All MH series of resistors environment use. are supplied tape pack ...
... environment of use. be takenoftouse. avoid potential sources of ionic contamination environment contacting the resistor body, for example, flux applied by Packaging spraying, encapsulation materials or contaminants from the Packaging All MH series of resistors environment use. are supplied tape pack ...
PSS30S71F6
... It is recommended to connect control GND and power GND at only a point N1 (near the terminal of shunt resistor). (2) It is recommended to insert a Zener diode D1(24V/1W) between each pair of control supply terminals to prevent surge destruction. (3) To prevent surge destruction, the wiring between t ...
... It is recommended to connect control GND and power GND at only a point N1 (near the terminal of shunt resistor). (2) It is recommended to insert a Zener diode D1(24V/1W) between each pair of control supply terminals to prevent surge destruction. (3) To prevent surge destruction, the wiring between t ...
UM10392 UBA2024T SO14 13 W demo board User manual
... The UBA2024T circuit is a half-bridge driver IC, which has been set-up to drive a standard PLC-13 W, G24q-2 socket based lamp or similar lamp types with a nominal lamp power of 12.5 W. The total power drawn from the mains is about 13 W at a nominal mains voltage of 230 V (RMS); 50 Hz or 120 V (RMS); ...
... The UBA2024T circuit is a half-bridge driver IC, which has been set-up to drive a standard PLC-13 W, G24q-2 socket based lamp or similar lamp types with a nominal lamp power of 12.5 W. The total power drawn from the mains is about 13 W at a nominal mains voltage of 230 V (RMS); 50 Hz or 120 V (RMS); ...
package ruggedness absolute maximum ratings features description
... Drain-Source Breakdown Drain Leakage Current Gate Leakage Current Power Gain ...
... Drain-Source Breakdown Drain Leakage Current Gate Leakage Current Power Gain ...
File
... Digital Multimeter Introduction • Choosing the right meter Category 1. With the likely hood of working in multiple different category environments always choose a meter that will be safe for working on the HIGHEST category that could potentially be accessed 2. Choose a Steady State Voltage rating t ...
... Digital Multimeter Introduction • Choosing the right meter Category 1. With the likely hood of working in multiple different category environments always choose a meter that will be safe for working on the HIGHEST category that could potentially be accessed 2. Choose a Steady State Voltage rating t ...
How to Select the Frequency Foldback Product Option When
... stages, abrupt changes in the load or in the input voltage may cause significant over or under−shoots. This circuit drastically limits these possible deviations from the regulation point. Safety Protections: NCP1602 features make the PFC stage extremely robust. Among them, we can mention the Brown−O ...
... stages, abrupt changes in the load or in the input voltage may cause significant over or under−shoots. This circuit drastically limits these possible deviations from the regulation point. Safety Protections: NCP1602 features make the PFC stage extremely robust. Among them, we can mention the Brown−O ...
I-V curves (KL)
... In a somewhat more involved manner, PTC-thermistors can be manufactured, e.g. using BaTiO3 . Temperature coefficients of PTCs may in certain temperature intervals become as large as 100% per Kelvin. PTC-components are used e.g. for limiting excess voltage or current, for current stabilisation and hi ...
... In a somewhat more involved manner, PTC-thermistors can be manufactured, e.g. using BaTiO3 . Temperature coefficients of PTCs may in certain temperature intervals become as large as 100% per Kelvin. PTC-components are used e.g. for limiting excess voltage or current, for current stabilisation and hi ...
skynet electronic specification m/n : snp-z106
... The efficiency is higher than 80% typ . while measuring at nominal line and rated load. 4.2 Hold up time The hold up time is longer than 16mS at 115VAC input and rated load , which is measured from the end of the last charging pulse to when the main output drops down to 95% output voltage. 4.3 Prote ...
... The efficiency is higher than 80% typ . while measuring at nominal line and rated load. 4.2 Hold up time The hold up time is longer than 16mS at 115VAC input and rated load , which is measured from the end of the last charging pulse to when the main output drops down to 95% output voltage. 4.3 Prote ...
Wiring - TCS Basys Controls
... • We use “Current Source” Outputs …Current is Pushed from the Controller Back to Ground ...
... • We use “Current Source” Outputs …Current is Pushed from the Controller Back to Ground ...
Comparing Circuit Protection Technologies for 48 V DC in High
... – Current ratings may require multiple MOVs in parallel – Repeated surges cause wear (leaded disc-type packages) and increase leakage – While clamping, voltage rises with surge current (less rigid) ...
... – Current ratings may require multiple MOVs in parallel – Repeated surges cause wear (leaded disc-type packages) and increase leakage – While clamping, voltage rises with surge current (less rigid) ...
MD2310FX
... The MD2310FX is manufactured using planar technology with diffused collector adopting new and enhanced high voltage structure. The MD product series show improved silicon efficiency bringing updated performance to the horizontal deflection stage. ...
... The MD2310FX is manufactured using planar technology with diffused collector adopting new and enhanced high voltage structure. The MD product series show improved silicon efficiency bringing updated performance to the horizontal deflection stage. ...
Electrical ballast
An electrical ballast is a device intended to limit the amount of current in an electric circuit. A familiar and widely used example is the inductive ballast used in fluorescent lamps, to limit the current through the tube, which would otherwise rise to destructive levels due to the tube's negative resistance characteristic.Ballasts vary in design complexity. They can be as simple as a series resistor or inductor, capacitors, or a combination thereof or as complex as electronic ballasts used with fluorescent lamps and high-intensity discharge lamps.