10-Bit, 40MHz, Current/Voltage-Output DACs General Description Features
... The MAX5181 is a 10-bit, current-output digital-to-analog converter (DAC) designed for superior performance in signal reconstruction or arbitrary waveform generation applications requiring analog signal reconstruction with low distortion and low-power operation. The MAX5184 provides equal specificat ...
... The MAX5181 is a 10-bit, current-output digital-to-analog converter (DAC) designed for superior performance in signal reconstruction or arbitrary waveform generation applications requiring analog signal reconstruction with low distortion and low-power operation. The MAX5184 provides equal specificat ...
Effects of Power Supply Resonances in Onset Studies of
... Based on the discussion of Sec. III.A, the voltage measurement across the FSBT must be made as closely as possible to the signal source, which is the thruster electrodes. We chose the new location of our voltage measurement to be 7.5 cm behind the upstream end of the thrust chamber, at the axial loc ...
... Based on the discussion of Sec. III.A, the voltage measurement across the FSBT must be made as closely as possible to the signal source, which is the thruster electrodes. We chose the new location of our voltage measurement to be 7.5 cm behind the upstream end of the thrust chamber, at the axial loc ...
50-mA, 24-V, 3.2-μA Supply Current Low
... Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. These are stress ratings only, which do not imply functional operation of the device at these or any other conditions beyond those indicated under Recommended Operating Conditions. Exposure to absol ...
... Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. These are stress ratings only, which do not imply functional operation of the device at these or any other conditions beyond those indicated under Recommended Operating Conditions. Exposure to absol ...
2139000 - ESCIES
... The range of frequencies within which the gain of the amplifier is not more than 3dB below the value of the midband gain. Midband gain is the gain at a specified frequency or the average gain over a specified frequency range. ...
... The range of frequencies within which the gain of the amplifier is not more than 3dB below the value of the midband gain. Midband gain is the gain at a specified frequency or the average gain over a specified frequency range. ...
SMP18 Octal Sample-and-Hold with Multiplexed Input
... range but have limited current sinking capability near VSS. In split supply operation, symmetrical output swings can be obtained by restricting the output range to 2 V from either supply. ...
... range but have limited current sinking capability near VSS. In split supply operation, symmetrical output swings can be obtained by restricting the output range to 2 V from either supply. ...
Circuit Theoretic Classification of Parallel Connected
... The output of any converter is normally expected to provide regulated voltage or current. Thus, an appropriate model for a converter (seen at output terminals) is either a voltage source or a current source. Two basic laws must be obeyed when connecting sources together. First, Kirchhoff’s voltage l ...
... The output of any converter is normally expected to provide regulated voltage or current. Thus, an appropriate model for a converter (seen at output terminals) is either a voltage source or a current source. Two basic laws must be obeyed when connecting sources together. First, Kirchhoff’s voltage l ...
The electric field
... CT-4 - The electric charge per unit area is +for infinite plate 1 and –for infinite plate 2.The magnitude of the electric field associated with plate 1 is and the electric field lines for this plate are as shown. When the two are placed parallel to one another, the magnitude of the elec ...
... CT-4 - The electric charge per unit area is +for infinite plate 1 and –for infinite plate 2.The magnitude of the electric field associated with plate 1 is and the electric field lines for this plate are as shown. When the two are placed parallel to one another, the magnitude of the elec ...
Primary-Side Sensing Takes Complexity out of Isolated Flyback
... through the flyback switching node waveform. During the switch off-period, the diode delivers the current to the output, and the output voltage is thus reflected to the primary-side of the flyback transformer (or the switch node). The magnitude of the switch node voltage is the summation of the inpu ...
... through the flyback switching node waveform. During the switch off-period, the diode delivers the current to the output, and the output voltage is thus reflected to the primary-side of the flyback transformer (or the switch node). The magnitude of the switch node voltage is the summation of the inpu ...
The LEDset (Gen2)
... meet this demand for greater adaptability by supporting a wide power and current range and by their future-proof design, which makes them ready for coming LED generations. Purpose of this application guide: The purpose of this application guide is to provide basic technical information on the LEDset ...
... meet this demand for greater adaptability by supporting a wide power and current range and by their future-proof design, which makes them ready for coming LED generations. Purpose of this application guide: The purpose of this application guide is to provide basic technical information on the LEDset ...
DIY – Dive-computer PC Interface
... pads are already on the PCBs of a few (maybe many more) standard USB-to-serial interfaces. The first step is to program the EEPROM. The EEPROM used in this project is a 24C02 serial (I2C) EEPROM in SMD format. The EEPROM can be programmed with any EEPROM programmer hardware and software that support ...
... pads are already on the PCBs of a few (maybe many more) standard USB-to-serial interfaces. The first step is to program the EEPROM. The EEPROM used in this project is a 24C02 serial (I2C) EEPROM in SMD format. The EEPROM can be programmed with any EEPROM programmer hardware and software that support ...
Illumination Utilization of Electrical Energ 6TH SEMESTER
... Uses of Instrument Transformer It is used for the following two as: 1. To insulate the high voltage circuit from the measuring circuit in order to protect the measuring instruments from burning 2. To make it possible to measure the high voltage with low range voltmeter and high current with low ran ...
... Uses of Instrument Transformer It is used for the following two as: 1. To insulate the high voltage circuit from the measuring circuit in order to protect the measuring instruments from burning 2. To make it possible to measure the high voltage with low range voltmeter and high current with low ran ...
Week 4-AC - khurramkamal
... ■ We can add the two phasors any way possible. That includes doing it graphically by hand, breaking the phasors into components and summing the real and imaginary components - as we did above - or any other way you can imagine to sum two vector-like quantities. ...
... ■ We can add the two phasors any way possible. That includes doing it graphically by hand, breaking the phasors into components and summing the real and imaginary components - as we did above - or any other way you can imagine to sum two vector-like quantities. ...
EE32828833
... D-STATCOM is employed at distribution level or at load side also behaves as shunt active filter. It works as the IEEE-519 standard limit. Since the electrical power distribution system it is very important to balance the supply and demand of active and reactive power in the electrical power system. ...
... D-STATCOM is employed at distribution level or at load side also behaves as shunt active filter. It works as the IEEE-519 standard limit. Since the electrical power distribution system it is very important to balance the supply and demand of active and reactive power in the electrical power system. ...
Capacitive Sensor
... Can be neglected, as long as there is no exertion of force to the measurement system. On request the sensor heads can be made of non-magnetic material, like Titanium. Radioactive radiation has no influence on measurements performed by capacitive sensors. Appropriate insulation materials guarantee lo ...
... Can be neglected, as long as there is no exertion of force to the measurement system. On request the sensor heads can be made of non-magnetic material, like Titanium. Radioactive radiation has no influence on measurements performed by capacitive sensors. Appropriate insulation materials guarantee lo ...