MAX8581/MAX8582 2.5MHz/1.5MHz Step-Down Converters with 60m Bypass in TDFN for CDMA PA Power
... Supply Voltage Input. 2.7V to 5.5V. Bypass with a 2.2µF ceramic capacitor as close as possible to IN and GND. Active-Low Shutdown Input. Connect to IN or logic-high for normal operation. Connect to GND or logic-low for shutdown mode. High-Power Mode Set Input. Drive HP high to invoke bypass mode. By ...
... Supply Voltage Input. 2.7V to 5.5V. Bypass with a 2.2µF ceramic capacitor as close as possible to IN and GND. Active-Low Shutdown Input. Connect to IN or logic-high for normal operation. Connect to GND or logic-low for shutdown mode. High-Power Mode Set Input. Drive HP high to invoke bypass mode. By ...
ULTRA SLIMPAK G108-0001 ® DC Powered DC Input Limit Alarm
... input signal status. Active DC power is indicated by an illuminated LED. If this LED is off, check DC power and the wiring connection. If the input signal is more than 110% of the full scale range, the LED will flash at 8 Hz. Below 0%, it flashes at 4 Hz. Two red LEDs indicate the relay state for ea ...
... input signal status. Active DC power is indicated by an illuminated LED. If this LED is off, check DC power and the wiring connection. If the input signal is more than 110% of the full scale range, the LED will flash at 8 Hz. Below 0%, it flashes at 4 Hz. Two red LEDs indicate the relay state for ea ...
1.0 Introduction - Electrical and Computer Engineering
... report is far more efficient and less costly then the previously method used. The basic idea of the circuit is to ‘control’ the MOSFET switching and regulate the output of the circuit without the need to do any tedious functions or conversions as can be seen above with the switching from DC-AC-DC. T ...
... report is far more efficient and less costly then the previously method used. The basic idea of the circuit is to ‘control’ the MOSFET switching and regulate the output of the circuit without the need to do any tedious functions or conversions as can be seen above with the switching from DC-AC-DC. T ...
A low-power, blocking-capacitor-free, charge-balanced electrode-stimulator chip with less than 6nA DC error for 1mA full-scale stimulation
... the current transacted across a small series resistor, and feeding back finely discretized charge packets to equilibrate the charge. As mentioned, the success of this technique then depends on the ability to minimize the charge-injection, noise, mismatch, leakage and other sampling errors to achieve ...
... the current transacted across a small series resistor, and feeding back finely discretized charge packets to equilibrate the charge. As mentioned, the success of this technique then depends on the ability to minimize the charge-injection, noise, mismatch, leakage and other sampling errors to achieve ...
HCF4066BEY
... intended for the transmission or multiplexing of analog or digital signals. It is pin for pin compatible with HCF4016B, but exhibits a much lower ON resistance. In addition, the ON resistance is relatively constant over the full input signal range. The HCF4066B consists of four independent bilateral ...
... intended for the transmission or multiplexing of analog or digital signals. It is pin for pin compatible with HCF4016B, but exhibits a much lower ON resistance. In addition, the ON resistance is relatively constant over the full input signal range. The HCF4066B consists of four independent bilateral ...
AN-912 Common Data Transmission Parameters and their Definitions
... power supply voltage applied. This parameter assures that the driver is disabled by an internal circuit at the specified power supply level, even though the enable pin is active. If the driver was enabled, IOS current would be observed, instead of the combined measured current of driver TRI-STATE® l ...
... power supply voltage applied. This parameter assures that the driver is disabled by an internal circuit at the specified power supply level, even though the enable pin is active. If the driver was enabled, IOS current would be observed, instead of the combined measured current of driver TRI-STATE® l ...
Lab #2 Voltage and Current Division
... This is a design problem. Your task is to design a circuit that will deliver 1.5V 5% across a load resistor of 10k. Figure 2.10 demonstrates the problem. The resistors available for use are listed in Figure 2.10. As with most engineering design problems, there are constraints. In this case, your ...
... This is a design problem. Your task is to design a circuit that will deliver 1.5V 5% across a load resistor of 10k. Figure 2.10 demonstrates the problem. The resistors available for use are listed in Figure 2.10. As with most engineering design problems, there are constraints. In this case, your ...
DATASHEET SEARCH SITE | WWW.ALLDATASHEET.COM
... The OPA541 can be used in applications currently using various hybrid power amplifiers, including the OPA501, OPA511, OPA512, and 3573. Of course, the application must be evaluated to assure that the output capability and other performance attributes of the OPA541 meet the necessary requirement. The ...
... The OPA541 can be used in applications currently using various hybrid power amplifiers, including the OPA501, OPA511, OPA512, and 3573. Of course, the application must be evaluated to assure that the output capability and other performance attributes of the OPA541 meet the necessary requirement. The ...
lecture4
... To measure voltage, we use a two-terminal device called a voltmeter. To measure current, we use a two-terminal device called a ammeter. To measure resistance, we use a two-terminal device called a ohmmeter. A multimeter can be setup to function as any of these three devices. In lab, you use a DMM to ...
... To measure voltage, we use a two-terminal device called a voltmeter. To measure current, we use a two-terminal device called a ammeter. To measure resistance, we use a two-terminal device called a ohmmeter. A multimeter can be setup to function as any of these three devices. In lab, you use a DMM to ...
Integrating ADC
An integrating ADC is a type of analog-to-digital converter that converts an unknown input voltage into a digital representation through the use of an integrator. In its most basic implementation, the unknown input voltage is applied to the input of the integrator and allowed to ramp for a fixed time period (the run-up period). Then a known reference voltage of opposite polarity is applied to the integrator and is allowed to ramp until the integrator output returns to zero (the run-down period). The input voltage is computed as a function of the reference voltage, the constant run-up time period, and the measured run-down time period. The run-down time measurement is usually made in units of the converter's clock, so longer integration times allow for higher resolutions. Likewise, the speed of the converter can be improved by sacrificing resolution.Converters of this type can achieve high resolution, but often do so at the expense of speed. For this reason, these converters are not found in audio or signal processing applications. Their use is typically limited to digital voltmeters and other instruments requiring highly accurate measurements.