MAX14984 Enhanced VGA Port Protector with Monitor General Description
... Note 1: When F1 and F2 are connected to a voltage higher than VCC, some current will be sinked (see the Detailed Description). Note 2: Package thermal resistances were obtained using the method described in JEDEC specification JESD51-7, using a fourlayer board. For detailed information on package t ...
... Note 1: When F1 and F2 are connected to a voltage higher than VCC, some current will be sinked (see the Detailed Description). Note 2: Package thermal resistances were obtained using the method described in JEDEC specification JESD51-7, using a fourlayer board. For detailed information on package t ...
Disconnect Individually Mounted
... d. Switches, with Class L fuse installed, shall be rated for use on systems capable of delivering not more than 200,000 rms symmetrical amperes at 600 VAC maximum. Switches shall have an interrupting rating of 12 times continuous ampere rating at 240, 480, and 600 VAC switches shall be 100% rated de ...
... d. Switches, with Class L fuse installed, shall be rated for use on systems capable of delivering not more than 200,000 rms symmetrical amperes at 600 VAC maximum. Switches shall have an interrupting rating of 12 times continuous ampere rating at 240, 480, and 600 VAC switches shall be 100% rated de ...
DG308A/DG309 Quad, SPST Analog Switches _______________General Description ____________________________Features
... The DG308A/DG309 are quad, single-pole-single-throw (SPST) analog switches. The DG308A is normally open (SPST, NO), while the DG309 is normally closed (SPST, NC). Both parts feature fast switching speeds and low onresistance over the analog range. Other features include a turn-on time under 120ns, a ...
... The DG308A/DG309 are quad, single-pole-single-throw (SPST) analog switches. The DG308A is normally open (SPST, NO), while the DG309 is normally closed (SPST, NC). Both parts feature fast switching speeds and low onresistance over the analog range. Other features include a turn-on time under 120ns, a ...
Introductory Circuit Analysis, Tenth Edition
... 1. Find the electric field strength at a point 2 m from a charge of 4 mC. 2. The electric field strength is 36 newtons/coulomb (N/C) at a point r meters from a charge of 0.064 mC. Find the distance r. SECTION 10.3 Capacitance 3. Find the capacitance of a parallel plate capacitor if 1400 mC of charge ...
... 1. Find the electric field strength at a point 2 m from a charge of 4 mC. 2. The electric field strength is 36 newtons/coulomb (N/C) at a point r meters from a charge of 0.064 mC. Find the distance r. SECTION 10.3 Capacitance 3. Find the capacitance of a parallel plate capacitor if 1400 mC of charge ...
The Basics of Photoelectric Controls
... Modulator so it is energized to "look" whenever the source is turned on. Synchronizing the modulator and demodulator creates a shutter effect that makes the sensor virtually immune to any ambient light conditions. Due to the fact that the modulator and demodulator are electronically tied together, t ...
... Modulator so it is energized to "look" whenever the source is turned on. Synchronizing the modulator and demodulator creates a shutter effect that makes the sensor virtually immune to any ambient light conditions. Due to the fact that the modulator and demodulator are electronically tied together, t ...
A plane can be uniquely determined by three non
... IEDs are typically simple measurement and control devices connected in a tree form to a merging unit, which performs the protection functions and acts as interface to the station bus (Figure 3). The timing requirements for the station and for the process bus are distinct, they dictate the redundancy ...
... IEDs are typically simple measurement and control devices connected in a tree form to a merging unit, which performs the protection functions and acts as interface to the station bus (Figure 3). The timing requirements for the station and for the process bus are distinct, they dictate the redundancy ...
50/30 PTCDF/T2 Operators Manual
... 4. Care must be taken during all soldering operations. It is unsafe to exceed the general specification to which diodes are tested for solder ability. This is 10 + 2 seconds at a temperature of 230°C + 5OC at a point % 6 2 % Z inch from the diode body. This is not as restrictive as it may sound, sin ...
... 4. Care must be taken during all soldering operations. It is unsafe to exceed the general specification to which diodes are tested for solder ability. This is 10 + 2 seconds at a temperature of 230°C + 5OC at a point % 6 2 % Z inch from the diode body. This is not as restrictive as it may sound, sin ...
AN-6203 Applying SG6203 to Control a Synchronous Rectifier of a
... completely released during the subsequent off time. Therefore, the secondary current reduces to zero before the primary switch is turned on. To prevent the discharge of the output capacitor through the conducting synchronous rectifier, the synchronous rectifier must be terminated once the secondary ...
... completely released during the subsequent off time. Therefore, the secondary current reduces to zero before the primary switch is turned on. To prevent the discharge of the output capacitor through the conducting synchronous rectifier, the synchronous rectifier must be terminated once the secondary ...
FSQ211 Green Mode Fairchild Power Switch (FPS ) ⎯
... the load current exceeding a pre-set level due to an unexpected event. In this situation, the protection circuit should be activated to protect the SMPS. However, even when the SMPS is operating normally, the overload protection (OLP) circuit can be activated during the load transition. To avoid thi ...
... the load current exceeding a pre-set level due to an unexpected event. In this situation, the protection circuit should be activated to protect the SMPS. However, even when the SMPS is operating normally, the overload protection (OLP) circuit can be activated during the load transition. To avoid thi ...
Switch
In electrical engineering, a switch is an electrical component that can break an electrical circuit, interrupting the current or diverting it from one conductor to another.The mechanism of a switch may be operated directly by a human operator to control a circuit (for example, a light switch or a keyboard button), may be operated by a moving object such as a door-operated switch, or may be operated by some sensing element for pressure, temperature or flow. A relay is a switch that is operated by electricity. Switches are made to handle a wide range of voltages and currents; very large switches may be used to isolate high-voltage circuits in electrical substations.