92 % typical efficiency • Input voltage range: 240 – 430
... n modules - n * 6 kVA. In the case of Max. Power 2, some of the modules may be operating over their nominal power. Functioning above the maximum power is however acceptable since the overcurrent protection only activates at an output current of ~27.5 A, however this is only possible when operating a ...
... n modules - n * 6 kVA. In the case of Max. Power 2, some of the modules may be operating over their nominal power. Functioning above the maximum power is however acceptable since the overcurrent protection only activates at an output current of ~27.5 A, however this is only possible when operating a ...
AN-5023 LVDS Compatibility with RS422 and RS485 Interface Standards AN-
... The LVDS interface circuit is not intended for direct interoperation with other interface technologies, like RS-422, RS-485, or even Positive Emitter Coupled Logic (PECL). Under certain conditions, inter-operation of LVDS with other interface circuits mentioned above may be possible but may require ...
... The LVDS interface circuit is not intended for direct interoperation with other interface technologies, like RS-422, RS-485, or even Positive Emitter Coupled Logic (PECL). Under certain conditions, inter-operation of LVDS with other interface circuits mentioned above may be possible but may require ...
The Oscilloscope Watch
... oscilloscope’s analog section and the battery monitor can be turned off when not needed. Figure 6 shows the load sharing system. This circuit was designed using Microchip’s application note AN1149. The power from the USB should supply the system load and charge the battery. When the USB power source ...
... oscilloscope’s analog section and the battery monitor can be turned off when not needed. Figure 6 shows the load sharing system. This circuit was designed using Microchip’s application note AN1149. The power from the USB should supply the system load and charge the battery. When the USB power source ...
What is an electric shock?
... Although the FELV part of a circuit uses an extra-low voltage, it is not adequately protected from accidental contact with higher voltages in other parts of the circuit. Therefore the protection requirements for the higher voltage have to be applied to the entire circuit. Examples for FELV circuits ...
... Although the FELV part of a circuit uses an extra-low voltage, it is not adequately protected from accidental contact with higher voltages in other parts of the circuit. Therefore the protection requirements for the higher voltage have to be applied to the entire circuit. Examples for FELV circuits ...
Evaluates: MAX1795/MAX1796/MAX1797 MAX1797 Evaluation Kit General Description Features
... step-up DC-DC converter for portable hand-held devices. Unlike typical boost circuits, the MAX1797 output is completely disconnected from the input in shutdown. The EV kit accepts a positive input voltage between 0.7V and VOUT and converts it to a 3.3V output for currents up to 500mA. The EV kit pro ...
... step-up DC-DC converter for portable hand-held devices. Unlike typical boost circuits, the MAX1797 output is completely disconnected from the input in shutdown. The EV kit accepts a positive input voltage between 0.7V and VOUT and converts it to a 3.3V output for currents up to 500mA. The EV kit pro ...
Protection components
... the position of the permanent magnet allows adjustment of the pick up value from 30% to 125 % of nominal value and adjustable drop out from 40% to 85% of pick-up value. Time delay can also be provided as an option. The mobile armature pivots without friction providing reliable operation and the perm ...
... the position of the permanent magnet allows adjustment of the pick up value from 30% to 125 % of nominal value and adjustable drop out from 40% to 85% of pick-up value. Time delay can also be provided as an option. The mobile armature pivots without friction providing reliable operation and the perm ...
A Simplified Active Input EMI Filter of Common-mode Voltage Cancellation
... Nowadays, the broader use of power electronic based loads (rectifiers, inverter, motor control systems, etc) has led to a growth of power pollution and conducted electromagnetic emissions also have been produced because of the nonlinear voltage or current characteristics of these loads. So that, the ...
... Nowadays, the broader use of power electronic based loads (rectifiers, inverter, motor control systems, etc) has led to a growth of power pollution and conducted electromagnetic emissions also have been produced because of the nonlinear voltage or current characteristics of these loads. So that, the ...
Chapter 6
... Properties of Inductors II • Like the ideal capacitor, the ideal inductor does not dissipate energy stored in it. • Energy stored will be returned to the circuit later • In reality, inductors do have internal resistance due to the wiring used to make them. • A real inductor thus has a winding resis ...
... Properties of Inductors II • Like the ideal capacitor, the ideal inductor does not dissipate energy stored in it. • Energy stored will be returned to the circuit later • In reality, inductors do have internal resistance due to the wiring used to make them. • A real inductor thus has a winding resis ...
Brake By Wire - ja505 - electronic automotive
... silicon switch with very low onstate resistance. It is configured as a high-side switch used to replace electro-mechanical relays, fuses, and discrete devices in power management applications. This silicon device is designed for harsh environments, and it includesself-recovery features. ...
... silicon switch with very low onstate resistance. It is configured as a high-side switch used to replace electro-mechanical relays, fuses, and discrete devices in power management applications. This silicon device is designed for harsh environments, and it includesself-recovery features. ...
Snap-Trol 183 Nema 1 Instruction Manual
... to corrosive contaminants, water, heavy dust, or restricted air flow. The maximum allowable ambient at full rated output is 120 degrees F (50 degrees C). 4.1 Wiring WARNING: Do not connect power to the drive until it has been confirmed that the drive nameplate voltage and incoming AC voltage are the ...
... to corrosive contaminants, water, heavy dust, or restricted air flow. The maximum allowable ambient at full rated output is 120 degrees F (50 degrees C). 4.1 Wiring WARNING: Do not connect power to the drive until it has been confirmed that the drive nameplate voltage and incoming AC voltage are the ...
KB2517721780
... inverter provides the total active power flow. For highpower medium voltage NPC, there are advantages to using latching devices such IGCTs rather than IGBTs, due to their lower losses and higher voltage blocking capability [23], [25], [27], imposing a restriction on the switching frequency. In this ...
... inverter provides the total active power flow. For highpower medium voltage NPC, there are advantages to using latching devices such IGCTs rather than IGBTs, due to their lower losses and higher voltage blocking capability [23], [25], [27], imposing a restriction on the switching frequency. In this ...
HF3034
... The EMD-4000 is a bulk resistance-type humidity sensor based on the impedance change of a thin-film polymer due to water vapour absorption. The polymer is deposited on Bismuth alloy terminals, which are set on a ceramic substrate. The sensor is excited by a low voltage alternating current and the im ...
... The EMD-4000 is a bulk resistance-type humidity sensor based on the impedance change of a thin-film polymer due to water vapour absorption. The polymer is deposited on Bismuth alloy terminals, which are set on a ceramic substrate. The sensor is excited by a low voltage alternating current and the im ...
