LM7805CT - LM7812CT- LM7824CT Positive Voltage Regulators
... GENERAL DESCRIPTION This series of fixed-voltage integrated-circuit voltage regulators is designed for a wide range of applications. These applications include on-card regulation for elimination of noise and distribution problems associated with single-point regulation. Each of these regulators can ...
... GENERAL DESCRIPTION This series of fixed-voltage integrated-circuit voltage regulators is designed for a wide range of applications. These applications include on-card regulation for elimination of noise and distribution problems associated with single-point regulation. Each of these regulators can ...
doc - Seattle Central
... error correction and not used in this section. V+ is connected to supply and V- is connected to “negative supply.” In some circuits this may be a potential lower than ground (perhaps achieved by introducing a second supply), but in this section this pin will be connected to circuit ground. The remai ...
... error correction and not used in this section. V+ is connected to supply and V- is connected to “negative supply.” In some circuits this may be a potential lower than ground (perhaps achieved by introducing a second supply), but in this section this pin will be connected to circuit ground. The remai ...
L298N datasheet
... publication are subject to change without notice. This publication supersedes and replaces all information previously supplied. STMicroelectronics products are not authorized for use as critical components in life support devices or systems without express written approval of STMicroelectronics. The ...
... publication are subject to change without notice. This publication supersedes and replaces all information previously supplied. STMicroelectronics products are not authorized for use as critical components in life support devices or systems without express written approval of STMicroelectronics. The ...
Oscilloscope and High Voltage Probe Facilitage Motor
... In designing the cells, and the system as a whole, care must be taken to minimize the inductance of the power buses connected to the cell output. Excessive inductance can cause “kickback” voltages to occur when an IGBT is rapidly switched off. Even though the effective DC supply voltage for the IGBT ...
... In designing the cells, and the system as a whole, care must be taken to minimize the inductance of the power buses connected to the cell output. Excessive inductance can cause “kickback” voltages to occur when an IGBT is rapidly switched off. Even though the effective DC supply voltage for the IGBT ...
Model 6620A - Krohn
... and 360.00° or ±180°. These two ranges can be manually or automatically selected. ...
... and 360.00° or ±180°. These two ranges can be manually or automatically selected. ...
TRANSPAK T700-0001 ™ Loop Powered Isolator
... The T700-0001 is a loop-powered isolator that accepts a current input (typically 4-20mA). It takes its power source voltage and the output current loop drive (500 Ohm, 10V compliance, max.) from the input current loop. The 1-20mA output current follows the input current signal. Span adjustment is pr ...
... The T700-0001 is a loop-powered isolator that accepts a current input (typically 4-20mA). It takes its power source voltage and the output current loop drive (500 Ohm, 10V compliance, max.) from the input current loop. The 1-20mA output current follows the input current signal. Span adjustment is pr ...
MOSFETs: Linear Model
... the signal is input to the low impedance base and the base-emitter diode is forward biased. • Another device achieved transistor action with the input diode junction reversed biased, and this device is called a "field effect transistor" or a "junction field effect transistor", JFET. • With the rever ...
... the signal is input to the low impedance base and the base-emitter diode is forward biased. • Another device achieved transistor action with the input diode junction reversed biased, and this device is called a "field effect transistor" or a "junction field effect transistor", JFET. • With the rever ...
TL081 OpAmp - U.C.C. Physics Department
... dress, component placement and supply decoupling in order to ensure stability. For example, resistors from the output to an input should be placed with the body close to the input to minimize ‘‘pick-up’’ and maximize the frequency of the feedback pole by minimizing the capacitance from the input to ...
... dress, component placement and supply decoupling in order to ensure stability. For example, resistors from the output to an input should be placed with the body close to the input to minimize ‘‘pick-up’’ and maximize the frequency of the feedback pole by minimizing the capacitance from the input to ...
ASL 3001P - Aelius Semiconductors Pte. Ltd.
... The device is ideal in designs where an analog DC control signal is required to control RF signal levels over a 30 dB amplitude range. The device features excellent I/O return losses. It is ideally suited for use where linear attenuation, fine tuning and very low power consumption are required. The ...
... The device is ideal in designs where an analog DC control signal is required to control RF signal levels over a 30 dB amplitude range. The device features excellent I/O return losses. It is ideally suited for use where linear attenuation, fine tuning and very low power consumption are required. The ...
Schmitt trigger
In electronics a Schmitt trigger is a comparator circuit with hysteresis implemented by applying positive feedback to the noninverting input of a comparator or differential amplifier. It is an active circuit which converts an analog input signal to a digital output signal. The circuit is named a ""trigger"" because the output retains its value until the input changes sufficiently to trigger a change. In the non-inverting configuration, when the input is higher than a chosen threshold, the output is high. When the input is below a different (lower) chosen threshold the output is low, and when the input is between the two levels the output retains its value. This dual threshold action is called hysteresis and implies that the Schmitt trigger possesses memory and can act as a bistable multivibrator (latch or flip-flop). There is a close relation between the two kinds of circuits: a Schmitt trigger can be converted into a latch and a latch can be converted into a Schmitt trigger.Schmitt trigger devices are typically used in signal conditioning applications to remove noise from signals used in digital circuits, particularly mechanical contact bounce. They are also used in closed loop negative feedback configurations to implement relaxation oscillators, used in function generators and switching power supplies.