Bipolar Junction Transistor (BJT) Modeling
... 1. Simulate the output characteristics (IC versus VCE) of an NPN BJT (2N3904) using PSpice. In so doing, apply a fixed base current IB, i.e., a current source, and sweep the collector voltage from 0 to 10V while the emitter remains grounded. Use the following 5 values for the base current IB: 2µA, 4 ...
... 1. Simulate the output characteristics (IC versus VCE) of an NPN BJT (2N3904) using PSpice. In so doing, apply a fixed base current IB, i.e., a current source, and sweep the collector voltage from 0 to 10V while the emitter remains grounded. Use the following 5 values for the base current IB: 2µA, 4 ...
AN2759
... D1, C1 and C3 constitute a charge pump circuit, which generates the supply voltage for the high-side integrated MOSFETs. Due to voltage and current switching at relatively high frequency, these components are connected through short paths in order to minimize induced noise on other circuitries. R1, ...
... D1, C1 and C3 constitute a charge pump circuit, which generates the supply voltage for the high-side integrated MOSFETs. Due to voltage and current switching at relatively high frequency, these components are connected through short paths in order to minimize induced noise on other circuitries. R1, ...
MSE15
... voltage across load resistor is zero. It indicates that A. diode is open circuited B. diode is short circuited C. resistor is open circuited D. diode is either short circuited or open circuited ...
... voltage across load resistor is zero. It indicates that A. diode is open circuited B. diode is short circuited C. resistor is open circuited D. diode is either short circuited or open circuited ...
Evaluates: MAX5025–MAX5028 MAX5026 Evaluation Kit General Description Features
... output voltage from a +3V to +11V input source. It delivers up to 6mA output current, depending on the input voltage. The MAX5026 is a constant-frequency, pulse-width-modulating (PWM), current-mode step-up voltage converter with an internal power switch that operates at 500kHz. This EV kit demonstra ...
... output voltage from a +3V to +11V input source. It delivers up to 6mA output current, depending on the input voltage. The MAX5026 is a constant-frequency, pulse-width-modulating (PWM), current-mode step-up voltage converter with an internal power switch that operates at 500kHz. This EV kit demonstra ...
Bio/Gas Sensor Characterizer
... The Bio/Gas Sensor Characterizer provides the user a limited ability to expand or otherwise change the setup to suit test requirements, localized entirely within the test circuit. Signal gain may be adjusted (3.6x to 10x) by setting the 20 kilo-ohm pot at R8. In the future, when hardy (projected lif ...
... The Bio/Gas Sensor Characterizer provides the user a limited ability to expand or otherwise change the setup to suit test requirements, localized entirely within the test circuit. Signal gain may be adjusted (3.6x to 10x) by setting the 20 kilo-ohm pot at R8. In the future, when hardy (projected lif ...
interface ASD-NIB Analog Signal & Discrete Non-Incendive Barrier
... This module provides isolation for a circuit on the load side of the module to be rated as non-incendive, and is to be used on digital inputs or outputs. The DNIB allows the use of non-rated wiring to end devices in Class 1, Zone 2 / Division 2 areas, subject to the allowances of the ...
... This module provides isolation for a circuit on the load side of the module to be rated as non-incendive, and is to be used on digital inputs or outputs. The DNIB allows the use of non-rated wiring to end devices in Class 1, Zone 2 / Division 2 areas, subject to the allowances of the ...
BDTIC Adjustable Linear Low Dropout LED Driver TLE4309
... by protecting from overcurrent and overtemperature The PWM/EN input permits LED brightness regulation by pulse width modulation. Setting the pin to “low” switches off the IC entirely. Due to the high impedance of the PWM/EN input, the TLE4309 can be used as a protected high side switch. Protection c ...
... by protecting from overcurrent and overtemperature The PWM/EN input permits LED brightness regulation by pulse width modulation. Setting the pin to “low” switches off the IC entirely. Due to the high impedance of the PWM/EN input, the TLE4309 can be used as a protected high side switch. Protection c ...
Interconnection Study Report for 10 MW of Wind Generation
... MRO 2007 Series 2009 summer peak model was used to perform the analysis. The 69 kV system connected to Maple River is not part of the standard MRO models, information provided by MPC was used to model the 69 kV system in this region. The loads along the 69 kV line from Maple River to Averill were mo ...
... MRO 2007 Series 2009 summer peak model was used to perform the analysis. The 69 kV system connected to Maple River is not part of the standard MRO models, information provided by MPC was used to model the 69 kV system in this region. The loads along the 69 kV line from Maple River to Averill were mo ...
PFT-301CM 30 kV Portable AC Hipot
... Models below 100 kVac are single piece units with a shielded cable output for fast and easy test setup. The PFT-103CM, PFT-303CM, PFT-503CM, and PFT-1003CM are compensated enabling testing of 3 kVA loads with a power draw of 1.5 kVA and operate from a conventional electrical source*. In addition, th ...
... Models below 100 kVac are single piece units with a shielded cable output for fast and easy test setup. The PFT-103CM, PFT-303CM, PFT-503CM, and PFT-1003CM are compensated enabling testing of 3 kVA loads with a power draw of 1.5 kVA and operate from a conventional electrical source*. In addition, th ...
RevF_088e
... Note: 25 ohms (50 ohm in parallel with 50 ohms) and 1 uF gives a 6.37 kHz - 3dB point if we bandwidth limit the current probe. Airbus does not want to bandwidth limit the current probe. Jean-Paul needs the first msec to be controlled for SSPCs. Note: Mario suggests a different standardization of the ...
... Note: 25 ohms (50 ohm in parallel with 50 ohms) and 1 uF gives a 6.37 kHz - 3dB point if we bandwidth limit the current probe. Airbus does not want to bandwidth limit the current probe. Jean-Paul needs the first msec to be controlled for SSPCs. Note: Mario suggests a different standardization of the ...
Power Voltage Transformers
... The high voltage primary terminal is made of aluminium alloy or, alternatively, of corrosion protected (tin or silver plated) electrolytic copper. The terminal shape and type are both chosen according to applicable standard and customers’ requirements and practice. Secondary windings terminals, alon ...
... The high voltage primary terminal is made of aluminium alloy or, alternatively, of corrosion protected (tin or silver plated) electrolytic copper. The terminal shape and type are both chosen according to applicable standard and customers’ requirements and practice. Secondary windings terminals, alon ...
Grade 9 Academic Science – Electricity
... equivalent to the product of the current between those two points (I) and the total resistance of all electrical devices present between those two points (R) Any better? In your own words, what does that statement say? ...
... equivalent to the product of the current between those two points (I) and the total resistance of all electrical devices present between those two points (R) Any better? In your own words, what does that statement say? ...
Model 523 - Krohn-Hite Corporation
... production, calibration labs, QA and QC departments, design labs, or any place where an accurate voltage and current source is needed. ...
... production, calibration labs, QA and QC departments, design labs, or any place where an accurate voltage and current source is needed. ...
Ohms Law Lab – Activity
... measured in Volts, or as Joules/Coulomb. Voltage provides the energy in the circuit needed to do work. Resistance is how much current is slowed by a device measured in Ohms. Electrical resistance is needed in a circuit. It allows the energy to be transformed into heat, light, motion, etc. Without re ...
... measured in Volts, or as Joules/Coulomb. Voltage provides the energy in the circuit needed to do work. Resistance is how much current is slowed by a device measured in Ohms. Electrical resistance is needed in a circuit. It allows the energy to be transformed into heat, light, motion, etc. Without re ...
Standard Power Data Sheet IFX21401
... The output voltage VQ is controlled by comparing it to the voltage applied at pin ADJ/EN and driving a PNP pass transistor accordingly. The control loop stability depends on the output capacitor CQ, the load current, the chip temperature and the poles/zeros introduced by the integrated circuit. To e ...
... The output voltage VQ is controlled by comparing it to the voltage applied at pin ADJ/EN and driving a PNP pass transistor accordingly. The control loop stability depends on the output capacitor CQ, the load current, the chip temperature and the poles/zeros introduced by the integrated circuit. To e ...
BAV19 / 20 / 21 Small Signal Diode B A
... support device or system whose failure to perform can the body, or (b) support or sustain life, or (c) whose be reasonably expected to cause the failure of the life failure to perform when properly used in accordance support device or system, or to affect its safety or with instructions for use prov ...
... support device or system whose failure to perform can the body, or (b) support or sustain life, or (c) whose be reasonably expected to cause the failure of the life failure to perform when properly used in accordance support device or system, or to affect its safety or with instructions for use prov ...
TS6001G3-2.5DB Datasheet
... 4) An optional load resistor ≥ 5kΩ and capacitor up to 2200pF can be soldered on the board. Solder the resistor on pads R1 and the capacitor on pads C1. If a load is not desired, leave these pads open and proceed to step 5. 5) Turn on the power supply and check that the digital voltmeter is reading ...
... 4) An optional load resistor ≥ 5kΩ and capacitor up to 2200pF can be soldered on the board. Solder the resistor on pads R1 and the capacitor on pads C1. If a load is not desired, leave these pads open and proceed to step 5. 5) Turn on the power supply and check that the digital voltmeter is reading ...
Voltage regulator
A voltage regulator is designed to automatically maintain a constant voltage level. A voltage regulator may be a simple ""feed-forward"" design or may include negative feedback control loops. It may use an electromechanical mechanism, or electronic components. Depending on the design, it may be used to regulate one or more AC or DC voltages.Electronic voltage regulators are found in devices such as computer power supplies where they stabilize the DC voltages used by the processor and other elements. In automobile alternators and central power station generator plants, voltage regulators control the output of the plant. In an electric power distribution system, voltage regulators may be installed at a substation or along distribution lines so that all customers receive steady voltage independent of how much power is drawn from the line.