Evaluates: MAX16834 MAX16834 Evaluation Kit General Description Features
... optional step-up/step-down (buck-boost) operation. The MAX16834 EV kit operates from a DC supply voltage of 7V to 28V and requires up to 5A. The MAX16834 EV kit circuit is configured to deliver up to 1A of current into series LEDs with a maximum forward voltage of 28V. The MAX16834 EV kit features t ...
... optional step-up/step-down (buck-boost) operation. The MAX16834 EV kit operates from a DC supply voltage of 7V to 28V and requires up to 5A. The MAX16834 EV kit circuit is configured to deliver up to 1A of current into series LEDs with a maximum forward voltage of 28V. The MAX16834 EV kit features t ...
SN75150 数据资料 dataSheet 下载
... Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant ...
... Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant ...
Electrostatic trapping of single conducting nanoparticles between
... close to the electrodes. Upon applying a voltage ~V! one will polarize conducting particles in the vicinity of the electrodes. Due to the field gradient near the nm-size gap the polarized particles will be attracted to the region between the electrodes, in the same way as any dipole is attracted to ...
... close to the electrodes. Upon applying a voltage ~V! one will polarize conducting particles in the vicinity of the electrodes. Due to the field gradient near the nm-size gap the polarized particles will be attracted to the region between the electrodes, in the same way as any dipole is attracted to ...
Instructions for SLO-SYN® MICRO SERIES Translator Oscillator
... motion control applications. In some cases, these applications produce electromagnetic interference (EMI, or electrical “noise”) that may cause inappropriate operation of the microprocessor logic used in the Micro Series product, or in any other computer-type equipment in the user’s system. This gui ...
... motion control applications. In some cases, these applications produce electromagnetic interference (EMI, or electrical “noise”) that may cause inappropriate operation of the microprocessor logic used in the Micro Series product, or in any other computer-type equipment in the user’s system. This gui ...
Features Mechanical Data
... Diodes Incorporated products are specifically not authorized for use as critical components in life support devices or systems without the express written approval of the Chief Executive Officer of Diodes Incorporated. As used herein: A. Life support devices or systems are devices or systems which: ...
... Diodes Incorporated products are specifically not authorized for use as critical components in life support devices or systems without the express written approval of the Chief Executive Officer of Diodes Incorporated. As used herein: A. Life support devices or systems are devices or systems which: ...
Motor Drive Lecture 1#C
... • The gears are used to amplify the torque on load side at lower speed compared to the motor speed • The motors are designed to run at high speeds because it has been found that the higher the speed, the lower is the volume and size of the motor ...
... • The gears are used to amplify the torque on load side at lower speed compared to the motor speed • The motors are designed to run at high speeds because it has been found that the higher the speed, the lower is the volume and size of the motor ...
ZXLD1360 Description Pin Assignments
... 1. ZXLD1360 will operate at higher frequencies but due to propagation delays accuracy will be affected. 2.100% brightness corresponds to VADJ = VADJ(nom) = VREF (~1.25V). Driving the ADJ pin above VREF will increase the VSENSE threshold and output current proportionally. ...
... 1. ZXLD1360 will operate at higher frequencies but due to propagation delays accuracy will be affected. 2.100% brightness corresponds to VADJ = VADJ(nom) = VREF (~1.25V). Driving the ADJ pin above VREF will increase the VSENSE threshold and output current proportionally. ...
Sep 1992 Design Techniques for Electrostatic Discharge Protection
... A practical implementation is shown in Figure 12. Gain limiting is provided by two Schottky diodes, which maintain the output at approximately +11dBm— sufficient to directly drive +7 or +10dBm diode-ring mixers. Output-stage clipping is not recommended as a means of gain limiting, as this increases ...
... A practical implementation is shown in Figure 12. Gain limiting is provided by two Schottky diodes, which maintain the output at approximately +11dBm— sufficient to directly drive +7 or +10dBm diode-ring mixers. Output-stage clipping is not recommended as a means of gain limiting, as this increases ...
Ram Racing - Colorado State University College of Engineering
... Estimation of sensed parameters (done automatically by BMS) ...
... Estimation of sensed parameters (done automatically by BMS) ...
Industrial Automation System
... voltage and current requirements of the load. Keep in mind that some loads (such as motor) draw more current when first turned on than they do not at steady state. Relay Application: The relay can be used to open and close high-voltage or high-current circuits with relatively little voltage and curr ...
... voltage and current requirements of the load. Keep in mind that some loads (such as motor) draw more current when first turned on than they do not at steady state. Relay Application: The relay can be used to open and close high-voltage or high-current circuits with relatively little voltage and curr ...
Design of Power and Delay Efficient 32 Bit X 32 Bit Multi
... and parallel processing.3) Look Up Table is like a storage element used to store voltage required for multiplication.4) Frequency scaling unit (FSU) which provides required frequency for the multiplication 5) voltage and frequency management unit (VFMU) which is receives user requirement and control ...
... and parallel processing.3) Look Up Table is like a storage element used to store voltage required for multiplication.4) Frequency scaling unit (FSU) which provides required frequency for the multiplication 5) voltage and frequency management unit (VFMU) which is receives user requirement and control ...
AAT3663 数据资料DataSheet下载
... Charge current programming pin. Connect a resistor between this pin and GND to program the constant fast charge current. IC ground connection. Connect this pin to power ground. Battery temperature sense input. Connect the Li-Ion battery pack NTC resistor terminal to this pin. Battery voltage sense p ...
... Charge current programming pin. Connect a resistor between this pin and GND to program the constant fast charge current. IC ground connection. Connect this pin to power ground. Battery temperature sense input. Connect the Li-Ion battery pack NTC resistor terminal to this pin. Battery voltage sense p ...
Surge arrestors John VA7JW outlines coaxial in
... The Surge Arrestors described in these notes are economy devices installed in series with a coaxial feed line to protect radio equipment from damage induced by lightning. There are many devices available ranging in sophistication, features, protection and cost. The two types studied here are basic, ...
... The Surge Arrestors described in these notes are economy devices installed in series with a coaxial feed line to protect radio equipment from damage induced by lightning. There are many devices available ranging in sophistication, features, protection and cost. The two types studied here are basic, ...
Documentation
... the design. Noise generate in this input stage gets amplified with each additional stage that follows. Furthermore, bandwidth achieved in the input stage gets compromised with the introduction of additional capacitance and resistance from other stages. Choosing this stage was most probably the most ...
... the design. Noise generate in this input stage gets amplified with each additional stage that follows. Furthermore, bandwidth achieved in the input stage gets compromised with the introduction of additional capacitance and resistance from other stages. Choosing this stage was most probably the most ...
