Physics 481 - Physics @ UIC
... Check the actual resistor values with the DMM to be sure. Make a note if the measured values are within the tolerance from the ones specified. Now use the 5 V power supply on the breadboard to apply a voltage to the divider. Use the DMM to measure the voltage across both resistors as well as each re ...
... Check the actual resistor values with the DMM to be sure. Make a note if the measured values are within the tolerance from the ones specified. Now use the 5 V power supply on the breadboard to apply a voltage to the divider. Use the DMM to measure the voltage across both resistors as well as each re ...
L6452
... the latter has a built - in aluminium resistor, whose value changes slightly with the temperature. The temperature determination is done by injecting a constant current in the resistor, and measuring the voltage drop across it. Since high - end printers have two heads, it must also be possible to sw ...
... the latter has a built - in aluminium resistor, whose value changes slightly with the temperature. The temperature determination is done by injecting a constant current in the resistor, and measuring the voltage drop across it. Since high - end printers have two heads, it must also be possible to sw ...
Monobloc Power Amplifier Stealth Max Users' Manual
... Biasing the output tubes________ The Stealth Max is designed to run the KT88 output tubes at a cathode (combined plate and screen grid) current of 60 mA per tube. With a plate voltage of 500 V, the plate dissipation is about 25 W for each tube (the KT88 is rated for 35 W). The correct bias conditio ...
... Biasing the output tubes________ The Stealth Max is designed to run the KT88 output tubes at a cathode (combined plate and screen grid) current of 60 mA per tube. With a plate voltage of 500 V, the plate dissipation is about 25 W for each tube (the KT88 is rated for 35 W). The correct bias conditio ...
MAX8515 - Maxim Integrated
... Low-cost, low-dropout linear regulators can be designed with the MAX8515A/MAX8515 and an external NPN transistor for cost-conscious applications that do not require overcurrent, short-circuit, or overtemperature protection. The MAX8515/MAX8515A are available in space-saving 5-pin SC70 and SOT23 pack ...
... Low-cost, low-dropout linear regulators can be designed with the MAX8515A/MAX8515 and an external NPN transistor for cost-conscious applications that do not require overcurrent, short-circuit, or overtemperature protection. The MAX8515/MAX8515A are available in space-saving 5-pin SC70 and SOT23 pack ...
EUP2983 White LED Driver For Buck-Boost Application
... White LED Driver For Buck-Boost Application DESCRIPTION ...
... White LED Driver For Buck-Boost Application DESCRIPTION ...
PART B UNIT I (i). State and prove Demorgan`s law (6) (EI May 2007
... ii. Draw and explain the circuit diagram of CMOS with NAND gates. (6) ...
... ii. Draw and explain the circuit diagram of CMOS with NAND gates. (6) ...
Alternating Current
... 3. The voltage V applied across a circuit element is given by V = (20 V)(sin(100t) The current flowing through the element is given by I = (2 A)sin(100t) Determine the electrical power delivered to the element at time t = 2.0 ms. Ans : 13.8 W 4. A alternating voltage V is given by V = (12 V)(sin(1 ...
... 3. The voltage V applied across a circuit element is given by V = (20 V)(sin(100t) The current flowing through the element is given by I = (2 A)sin(100t) Determine the electrical power delivered to the element at time t = 2.0 ms. Ans : 13.8 W 4. A alternating voltage V is given by V = (12 V)(sin(1 ...
Comparative Study of 4-Bit ALU using CMOS and BiCMOS for
... Unfortunately, reducing the power supply voltage reduces power, but when the supply voltage is near to threshold voltage, the delay increases drastically [2]. This problem in CMOS can be overcome by using BiCMOS technology. BiCMOS technology marries both CMOS and bipolar (BJT) structure on the same ...
... Unfortunately, reducing the power supply voltage reduces power, but when the supply voltage is near to threshold voltage, the delay increases drastically [2]. This problem in CMOS can be overcome by using BiCMOS technology. BiCMOS technology marries both CMOS and bipolar (BJT) structure on the same ...
ADP3309 数据手册DataSheet 下载
... ADP3309 is stable with a wide range of capacitor values, types, and ESR (anyCAP). A capacitor as low as 0.47 μF is all that is needed for stability. However, larger capacitors can be used if high output current surges are anticipated. The ADP3309 is stable with extremely low ESR capacitors (ESR ≈ 0) ...
... ADP3309 is stable with a wide range of capacitor values, types, and ESR (anyCAP). A capacitor as low as 0.47 μF is all that is needed for stability. However, larger capacitors can be used if high output current surges are anticipated. The ADP3309 is stable with extremely low ESR capacitors (ESR ≈ 0) ...
Transistor–transistor logic
Transistor–transistor logic (TTL) is a class of digital circuits built from bipolar junction transistors (BJT) and resistors. It is called transistor–transistor logic because both the logic gating function (e.g., AND) and the amplifying function are performed by transistors (contrast with RTL and DTL).TTL is notable for being a widespread integrated circuit (IC) family used in many applications such as computers, industrial controls, test equipment and instrumentation, consumer electronics, synthesizers, etc. The designation TTL is sometimes used to mean TTL-compatible logic levels, even when not associated directly with TTL integrated circuits, for example as a label on the inputs and outputs of electronic instruments.After their introduction in integrated circuit form in 1963 by Sylvania, TTL integrated circuits were manufactured by several semiconductor companies, with the 7400 series (also called 74xx) by Texas Instruments becoming particularly popular. TTL manufacturers offered a wide range of logic gate, flip-flops, counters, and other circuits. Several variations from the original bipolar TTL concept were developed, giving circuits with higher speed or lower power dissipation to allow optimization of a design. TTL circuits simplified design of systems compared to earlier logic families, offering superior speed to resistor–transistor logic (RTL) and easier design layout than emitter-coupled logic (ECL). The design of the input and outputs of TTL gates allowed many elements to be interconnected.TTL became the foundation of computers and other digital electronics. Even after much larger scale integrated circuits made multiple-circuit-board processors obsolete, TTL devices still found extensive use as the ""glue"" logic interfacing more densely integrated components. TTL devices were originally made in ceramic and plastic dual-in-line (DIP) packages, and flat-pack form. TTL chips are now also made in surface-mount packages. Successors to the original bipolar TTL logic often are interchangeable in function with the original circuits, but with improved speed or lower power dissipation.