![Slic-dc](http://s1.studyres.com/store/data/001860921_1-7b2a3d601478097e8e874e9baca06a4e-300x300.png)
Topology Selection: Input
... – This helped greatly with the frequency response of the amplifier but did not remove the RHPZ – Resulted in bigger compensation capacitor because now the miller capacitance is in series with the CDS of the cascode device, reducing the effective capacitance – Zero nulling resistor was added to remov ...
... – This helped greatly with the frequency response of the amplifier but did not remove the RHPZ – Resulted in bigger compensation capacitor because now the miller capacitance is in series with the CDS of the cascode device, reducing the effective capacitance – Zero nulling resistor was added to remov ...
R and X in Series
... must be dropped across RE. This determines how much current must flow through RE and thus through RC. That sets the DC bias of the collector. Note how the base and collector currents were figured out without concern for the b of the transistor. This design is much more temperature-stable than the si ...
... must be dropped across RE. This determines how much current must flow through RE and thus through RC. That sets the DC bias of the collector. Note how the base and collector currents were figured out without concern for the b of the transistor. This design is much more temperature-stable than the si ...
High Definition Stereo Headphone Amplifier Ear+ Purist HD Ear+ HD300
... tubes, which were made in the United Kingdom, probably in the 1960s. These are low noise versions of the earlier EF36 and EF37 tubes and were the prototype for the EF86 miniature audio pentode. The 6J7 (metal) and 6J7G are electrically equivalent and can be substituted in the HD300. The 1620 is a sp ...
... tubes, which were made in the United Kingdom, probably in the 1960s. These are low noise versions of the earlier EF36 and EF37 tubes and were the prototype for the EF86 miniature audio pentode. The 6J7 (metal) and 6J7G are electrically equivalent and can be substituted in the HD300. The 1620 is a sp ...
Technical Notes
... pullup resistor that can be enabled or disabled, as well as a simultaneous analog and digital input. In fact, when you designate a Core 110f’s GPIO input as “raw” in Q-SYS Designer, two control pins appear: one analog and one digital. You may use either one or both simultaneously. They respectively ...
... pullup resistor that can be enabled or disabled, as well as a simultaneous analog and digital input. In fact, when you designate a Core 110f’s GPIO input as “raw” in Q-SYS Designer, two control pins appear: one analog and one digital. You may use either one or both simultaneously. They respectively ...
L3 Ohms_law
... Connect the circuit as shown in Figure 1. Identify the Resistor provided using the resistor colour code and ohmmeter. Set the d.c. supply voltage initially to zero volts. Adjust the supply voltage so that the resistance draws a current of 1 mA. Read the potential difference across the resistance R w ...
... Connect the circuit as shown in Figure 1. Identify the Resistor provided using the resistor colour code and ohmmeter. Set the d.c. supply voltage initially to zero volts. Adjust the supply voltage so that the resistance draws a current of 1 mA. Read the potential difference across the resistance R w ...
Transistor–transistor logic
![](https://commons.wikimedia.org/wiki/Special:FilePath/68k_ttl.jpg?width=300)
Transistor–transistor logic (TTL) is a class of digital circuits built from bipolar junction transistors (BJT) and resistors. It is called transistor–transistor logic because both the logic gating function (e.g., AND) and the amplifying function are performed by transistors (contrast with RTL and DTL).TTL is notable for being a widespread integrated circuit (IC) family used in many applications such as computers, industrial controls, test equipment and instrumentation, consumer electronics, synthesizers, etc. The designation TTL is sometimes used to mean TTL-compatible logic levels, even when not associated directly with TTL integrated circuits, for example as a label on the inputs and outputs of electronic instruments.After their introduction in integrated circuit form in 1963 by Sylvania, TTL integrated circuits were manufactured by several semiconductor companies, with the 7400 series (also called 74xx) by Texas Instruments becoming particularly popular. TTL manufacturers offered a wide range of logic gate, flip-flops, counters, and other circuits. Several variations from the original bipolar TTL concept were developed, giving circuits with higher speed or lower power dissipation to allow optimization of a design. TTL circuits simplified design of systems compared to earlier logic families, offering superior speed to resistor–transistor logic (RTL) and easier design layout than emitter-coupled logic (ECL). The design of the input and outputs of TTL gates allowed many elements to be interconnected.TTL became the foundation of computers and other digital electronics. Even after much larger scale integrated circuits made multiple-circuit-board processors obsolete, TTL devices still found extensive use as the ""glue"" logic interfacing more densely integrated components. TTL devices were originally made in ceramic and plastic dual-in-line (DIP) packages, and flat-pack form. TTL chips are now also made in surface-mount packages. Successors to the original bipolar TTL logic often are interchangeable in function with the original circuits, but with improved speed or lower power dissipation.