High PSR Low Drop-out Voltage Regulator (LDO)
... respectively of pass element and β is the result of voltage divider feedback network. As discussed previously in section II-B the performance of the error amplifier is directly correlated with the PSSR of the LDO system. The intuitive mode analysis of P SRR helps in the definition of error amplifier ...
... respectively of pass element and β is the result of voltage divider feedback network. As discussed previously in section II-B the performance of the error amplifier is directly correlated with the PSSR of the LDO system. The intuitive mode analysis of P SRR helps in the definition of error amplifier ...
Gate and Base Circuits and Protection
... Fast switch-on MOSFET switching circuit ........................................................ 237 Totem pole gate drive circuit with pulse-edge shaping...................................... 238 The waveform of the base current for a BJT base drive .................................... 239 (a) Circ ...
... Fast switch-on MOSFET switching circuit ........................................................ 237 Totem pole gate drive circuit with pulse-edge shaping...................................... 238 The waveform of the base current for a BJT base drive .................................... 239 (a) Circ ...
Design Considerations, Testing and Applications Assistance Form
... It is also often necessary to construct load lines to determine reflection waveforms in line driving applications. The input and output characteristics graphs of section 3 (Figs. 2-4, 2-7 and 2-8) can be very useful for this purpose. OUTPUT RISE AND FALL TIMES provide important information in determ ...
... It is also often necessary to construct load lines to determine reflection waveforms in line driving applications. The input and output characteristics graphs of section 3 (Figs. 2-4, 2-7 and 2-8) can be very useful for this purpose. OUTPUT RISE AND FALL TIMES provide important information in determ ...
Wideband, Low-Distortion Fully Differential Amplifiers (Rev. D)
... This is the point where distortion starts to substantially increase. Thermal management of the final PCB should strive to keep the junction temperature at or below 125°C for best performance and ...
... This is the point where distortion starts to substantially increase. Thermal management of the final PCB should strive to keep the junction temperature at or below 125°C for best performance and ...
Surface Mount RF Schottky Barrier Diodes Technical Data HSMS-282x Series
... the fewest possible processing steps to minimize variations in diode characteristics. Statistical data on the consistency of this product, in terms of SPICE parameters, is available from Agilent. ...
... the fewest possible processing steps to minimize variations in diode characteristics. Statistical data on the consistency of this product, in terms of SPICE parameters, is available from Agilent. ...
SN74LV4046A High-Speed CMOS Logic Phase
... and a comparator input are common to each comparator as shown in the Functional Block Diagram. The signal input can be directly coupled to large voltage signals, or indirectly coupled (with a series capacitor) to small voltage signals. A self-bias input circuit keeps small voltage signals within the ...
... and a comparator input are common to each comparator as shown in the Functional Block Diagram. The signal input can be directly coupled to large voltage signals, or indirectly coupled (with a series capacitor) to small voltage signals. A self-bias input circuit keeps small voltage signals within the ...
Grounding of AC generators and switching the neutral
... Power topic #6005 | Page on a 3-phase 4-wire system. System grounding, in other words, describes the practice of grounding one conductor of an AC power system. Equipment grounding refers to the bonding and grounding of all non-current carrying (during normal operation) metal conduit, equipment en ...
... Power topic #6005 | Page on a 3-phase 4-wire system. System grounding, in other words, describes the practice of grounding one conductor of an AC power system. Equipment grounding refers to the bonding and grounding of all non-current carrying (during normal operation) metal conduit, equipment en ...
AD8651
... distortion, rail-to-rail CMOS operational amplifiers that run from a single-supply voltage of 2.7 V to 5.5 V. The AD865x family is made up of rail-to-rail input and output amplifiers with a gain bandwidth of 50 MHz and a typical voltage offset of 100 μV across common mode from a 5 V supply. It also ...
... distortion, rail-to-rail CMOS operational amplifiers that run from a single-supply voltage of 2.7 V to 5.5 V. The AD865x family is made up of rail-to-rail input and output amplifiers with a gain bandwidth of 50 MHz and a typical voltage offset of 100 μV across common mode from a 5 V supply. It also ...
Analog Dialogue Volume 43, Number 2, 2009
... Generator/synchronizer, network clock .................................AD9548 Isolators, digital, 4-channel, 5-kV ......................................................... ..................................................ADuM4400/ADuM4401/ADuM4402 Microcontroller, precision analog, two 24-bit ADC ...
... Generator/synchronizer, network clock .................................AD9548 Isolators, digital, 4-channel, 5-kV ......................................................... ..................................................ADuM4400/ADuM4401/ADuM4402 Microcontroller, precision analog, two 24-bit ADC ...
