![LT3796/LT3796-1 - 100V Constant-Current and Constant](http://s1.studyres.com/store/data/001023642_1-443d3834c2ce14827673014348edb7d5-300x300.png)
K40 RTTY Module Guide
... your transceiver and switches to ground when active. This usually goes to the key input but check your transceiver’s manual to be sure. The K40 KEY output is used to frequency shift key your transceiver in FSK mode. If your transceiver has a direct FSK input it’s the easiest way to go. Use Table 1.1 ...
... your transceiver and switches to ground when active. This usually goes to the key input but check your transceiver’s manual to be sure. The K40 KEY output is used to frequency shift key your transceiver in FSK mode. If your transceiver has a direct FSK input it’s the easiest way to go. Use Table 1.1 ...
Sound Reproduction By Wave Field Synthesis
... most current stereophonic configuration: the two-channel stereophony. The sound reproduction method using the stereophonic principle is based on the binaural principle. This enables to localize a sound source, due to the analysis done by the brain of the two different signals received by both ears. ...
... most current stereophonic configuration: the two-channel stereophony. The sound reproduction method using the stereophonic principle is based on the binaural principle. This enables to localize a sound source, due to the analysis done by the brain of the two different signals received by both ears. ...
Performance of Transmission Lines
... A transmission line has *three constants R, L and C distributed uniformly along the whole length of the line. The resistance and inductance form the series impedance. The capacitance existing between conductors for 1-phase line or from a conductor to neutral for a 3-phase line forms a shunt path thr ...
... A transmission line has *three constants R, L and C distributed uniformly along the whole length of the line. The resistance and inductance form the series impedance. The capacitance existing between conductors for 1-phase line or from a conductor to neutral for a 3-phase line forms a shunt path thr ...
The SR560 (manual - Stanford Research Systems
... and listen-only RS-232 interface lines are provided for instrument control. Digital noise is eliminated by shutting down the microprocessor's oscillator except during the short time required to alter the instrument's configuration, either through a front-panel pushbutton or through an RS232 command. ...
... and listen-only RS-232 interface lines are provided for instrument control. Digital noise is eliminated by shutting down the microprocessor's oscillator except during the short time required to alter the instrument's configuration, either through a front-panel pushbutton or through an RS232 command. ...
Dynaudio Professional BM14S II manual.indd
... be combined in the BM14S II and routed accordingly. This To connect LFE/Slave input of the following subwoofer. This one now becomes the slave. allows the BM14S II to reproduce both the LFE channel 1. Connect the first subwoofer as described before. 4. Set the Mode switch of the second subwoofer ...
... be combined in the BM14S II and routed accordingly. This To connect LFE/Slave input of the following subwoofer. This one now becomes the slave. allows the BM14S II to reproduce both the LFE channel 1. Connect the first subwoofer as described before. 4. Set the Mode switch of the second subwoofer ...
ADM691A 数据手册DataSheet 下载
... low. The reset voltage threshold is 4.65 V (ADM691A/ ADM800L) or 4.4 V (ADM693A/ADM800M). On power-up RESET will remain low for 200 milliseconds after VCC rises above the appropriate reset threshold. This allows time for the power supply and microprocessor to stabilize. On powerdown, the RESET outpu ...
... low. The reset voltage threshold is 4.65 V (ADM691A/ ADM800L) or 4.4 V (ADM693A/ADM800M). On power-up RESET will remain low for 200 milliseconds after VCC rises above the appropriate reset threshold. This allows time for the power supply and microprocessor to stabilize. On powerdown, the RESET outpu ...
Slide 1
... A BJT consists of three differently doped semiconductor regions, the emitter region, the base region and the collector region. – These regions are, respectively, p type, n type and p type in a PNP transistor ( - and n type, p type and n type in a NPN transistor). – Each semiconductor region is conne ...
... A BJT consists of three differently doped semiconductor regions, the emitter region, the base region and the collector region. – These regions are, respectively, p type, n type and p type in a PNP transistor ( - and n type, p type and n type in a NPN transistor). – Each semiconductor region is conne ...
Construction and Evaluation of a Fast Switching Trigger Circuit for a
... Junction Transistor (BJT), Insulated Gate Bipolar Transistor (IGBT), 1:53 gain pulsed transformer and a triggered spark gap. The qualitative response of each component is assessed with respect to its response and relaxation time. The overall delay time between electronic input and this 6.7kV pulse i ...
... Junction Transistor (BJT), Insulated Gate Bipolar Transistor (IGBT), 1:53 gain pulsed transformer and a triggered spark gap. The qualitative response of each component is assessed with respect to its response and relaxation time. The overall delay time between electronic input and this 6.7kV pulse i ...
Digitally Isolated 2-Channel, Wide AC/DC Binary Input Module (Rev
... The binary inputs sense a change of the state of the external device. When these external devices are located in a harsh industrial environments (either outdoor or indoor), their contacts can be exposed to various types of contamination. Normally, there is a thin film of insulating sulfidation, oxid ...
... The binary inputs sense a change of the state of the external device. When these external devices are located in a harsh industrial environments (either outdoor or indoor), their contacts can be exposed to various types of contamination. Normally, there is a thin film of insulating sulfidation, oxid ...
18-Bit, 1.5 LSB INL, 250 kSPS PulSAR Differential ADC in MSOP/QFN AD7691
... Reference Input Voltage. The REF range is from 0.5 V to VDD. It is referred to the GND pin. This pin should be decoupled closely to the pin with a 10 μF capacitor. Power Supply. Differential Positive Analog Input. Referenced to IN−. The input range for IN+ is between 0 V and VREF, centered about VRE ...
... Reference Input Voltage. The REF range is from 0.5 V to VDD. It is referred to the GND pin. This pin should be decoupled closely to the pin with a 10 μF capacitor. Power Supply. Differential Positive Analog Input. Referenced to IN−. The input range for IN+ is between 0 V and VREF, centered about VRE ...
OKY T/3, T/5-W5 Series
... If the overcurrent condition still exists, the restart current will be removed and then tried again. This short current pulse prevents overheating and damaging the converter. Once the fault is removed, the converter immediately recovers normal operation. ...
... If the overcurrent condition still exists, the restart current will be removed and then tried again. This short current pulse prevents overheating and damaging the converter. Once the fault is removed, the converter immediately recovers normal operation. ...