Sub-uHz MOSFET 1/f noise measurements
... Fig. 2 shows the standard deviation of DI0 against a for 60 days of data. We use a ¼ 2.4 since, as shown in the Figure, this choice minimises the standard deviation of DI0 . The existence of a unique minimum indicates that our assumption of a linear dependence of drain current on temperature is corr ...
... Fig. 2 shows the standard deviation of DI0 against a for 60 days of data. We use a ¼ 2.4 since, as shown in the Figure, this choice minimises the standard deviation of DI0 . The existence of a unique minimum indicates that our assumption of a linear dependence of drain current on temperature is corr ...
poster
... require RF power levels of ~ 1 MW per cavity to produce a measurable amount of cooling. Peak power levels of this magnitude, in this frequency band require conventional high power vacuum tube technology, triodes and tetrodes. Four chains of three amplifiers will each produce a final stage RF pulse p ...
... require RF power levels of ~ 1 MW per cavity to produce a measurable amount of cooling. Peak power levels of this magnitude, in this frequency band require conventional high power vacuum tube technology, triodes and tetrodes. Four chains of three amplifiers will each produce a final stage RF pulse p ...
Liebert® PSA
... The Liebert PSA is an economical, environmentally-friendly line-interactive UPS that offers full- featured power protection for small office computers and electronic equipment. Liebert Multilink software automatically powers down your computer in the event of an extended power outage. It also has fu ...
... The Liebert PSA is an economical, environmentally-friendly line-interactive UPS that offers full- featured power protection for small office computers and electronic equipment. Liebert Multilink software automatically powers down your computer in the event of an extended power outage. It also has fu ...
SICAM-Q200
... monitoring and recording with magnitude and time stamp (duration) Rapid voltage changes (RVC) Limit value violations Waveform capture of triggered events of voltage and current. Up to 10 seconds records must be possible. ...
... monitoring and recording with magnitude and time stamp (duration) Rapid voltage changes (RVC) Limit value violations Waveform capture of triggered events of voltage and current. Up to 10 seconds records must be possible. ...
T 973 7-Channel Power Amplifier
... Individual gain adjustment for each channel promotes easy, accurate system configuration, as does the T 973’s integral 12V trigger turn-on response. This multi-channel amplifier delivers its output via heavy-duty “five-way” connectors. Ruggedness and in-system reliability are critical to successful ...
... Individual gain adjustment for each channel promotes easy, accurate system configuration, as does the T 973’s integral 12V trigger turn-on response. This multi-channel amplifier delivers its output via heavy-duty “five-way” connectors. Ruggedness and in-system reliability are critical to successful ...
the WS-G5487-C Datasheet
... voltage defined as the full 16 bit value (0 – 65535) with LSB equal to 100 µVolt, yielding a total range of 0 to +6.55 Volts. Transceiver TX bias current, internally measured, represented as a 16 bit unsigned integer with the current defined as the full 16 bit value (0 – 65535) with LSB equal to 2 µ ...
... voltage defined as the full 16 bit value (0 – 65535) with LSB equal to 100 µVolt, yielding a total range of 0 to +6.55 Volts. Transceiver TX bias current, internally measured, represented as a 16 bit unsigned integer with the current defined as the full 16 bit value (0 – 65535) with LSB equal to 2 µ ...
Shunt reactive power compensation
... substation can raise voltage when the load is high. The shunt capacitor banks can be permanently connected to the bus (fixed capacitor bank) or can be switched as needed. Switching can be based on time, if load variation is predictable, or can be based on voltage, power factor, or line current. Gene ...
... substation can raise voltage when the load is high. The shunt capacitor banks can be permanently connected to the bus (fixed capacitor bank) or can be switched as needed. Switching can be based on time, if load variation is predictable, or can be based on voltage, power factor, or line current. Gene ...
Synchronous Motor
... The Synchronous-Motor Power Equation • VTIacosθi = -(VTEf/Xs)sinδ • VTIacosθi = power input per phase = Pin,1Φ • -(VTEf/Xs)sinδ = magnet power per phase developed by a cylindrical-rotor motor (a function of Ef and δ) • Pin,1Φ = -(VTEf/Xs)sinδ is the synchronousmachine power equation • For three pha ...
... The Synchronous-Motor Power Equation • VTIacosθi = -(VTEf/Xs)sinδ • VTIacosθi = power input per phase = Pin,1Φ • -(VTEf/Xs)sinδ = magnet power per phase developed by a cylindrical-rotor motor (a function of Ef and δ) • Pin,1Φ = -(VTEf/Xs)sinδ is the synchronousmachine power equation • For three pha ...
Investigating the Transistor: A hands on activity.
... Investigating the Transistor: A hands on activity. You will be • assembling a one transistor amplifier circuit, • making it operational, then • taking measurements to determine the Current Gain and Voltage Gain and finally, if time, • Observing the operation with low frequency AC. ...
... Investigating the Transistor: A hands on activity. You will be • assembling a one transistor amplifier circuit, • making it operational, then • taking measurements to determine the Current Gain and Voltage Gain and finally, if time, • Observing the operation with low frequency AC. ...
EENG 457 Power System Analysis I
... (a) the instantaneous power. (b) the real and reactive power delivered by the source. (c) the power factor at the terminals of the source. 2. A voltage source v(t ) 100cos(100 t 60 ) V is connected to an impedance Z 5.030 . (a) Determine the expressions for the current and the instantaneous ...
... (a) the instantaneous power. (b) the real and reactive power delivered by the source. (c) the power factor at the terminals of the source. 2. A voltage source v(t ) 100cos(100 t 60 ) V is connected to an impedance Z 5.030 . (a) Determine the expressions for the current and the instantaneous ...