File
... In an electronic circuit, a combination of high voltage (+5V) and low voltage (0V) is usually used to represent a binary number. For example, a binary number 1010 is represented by ...
... In an electronic circuit, a combination of high voltage (+5V) and low voltage (0V) is usually used to represent a binary number. For example, a binary number 1010 is represented by ...
DC Thyristor 6CV Charger Datasheet DC Thyristor 6CV Charger
... Dale Power Solutions Ltd reserves the right to make changes in specification without notice or liability. All information is subject to Dale Power Solutions own data & is considered accurate at time of publishing. ...
... Dale Power Solutions Ltd reserves the right to make changes in specification without notice or liability. All information is subject to Dale Power Solutions own data & is considered accurate at time of publishing. ...
Electrical Interface of Logic Devices
... higher current or voltage requirements. • In digital electronics, transistors are used as switches. For the example below, a logic high will turn it on; a low will turn it off. V Bias ...
... higher current or voltage requirements. • In digital electronics, transistors are used as switches. For the example below, a logic high will turn it on; a low will turn it off. V Bias ...
PHOTOELECTRIC BEAM SENSOR
... ＊Automatic Gain Control circuit loaded ＊Wide adjustment (horizontally±90ﾟ,vertically±10ﾟ) ＊Two different colors housing (Black/White) ...
... ＊Automatic Gain Control circuit loaded ＊Wide adjustment (horizontally±90ﾟ,vertically±10ﾟ) ＊Two different colors housing (Black/White) ...
AIC3412
... The AIC3412 is a synchronous step-up DC/DC converter. That is base on constant Off Time/PSM controller topology. The IC enters PSM mode automatically at light load, the goal is to improve efficiency and reduce quiescent current. The AIC3412 provide a complete power supply solution for products power ...
... The AIC3412 is a synchronous step-up DC/DC converter. That is base on constant Off Time/PSM controller topology. The IC enters PSM mode automatically at light load, the goal is to improve efficiency and reduce quiescent current. The AIC3412 provide a complete power supply solution for products power ...
electric current
... • Ampere (A or amps) - unit used to measure the amount of charge that flows in a given time ...
... • Ampere (A or amps) - unit used to measure the amount of charge that flows in a given time ...
tripping signal switch 2co, 250vac/4a, snap-on
... • The contact material and construction are particularly suitable for low voltages • Function of the two change-over contacts switched to trigger signal contact (electrical signals triggering) • Test button for contact function "electric tripping " ...
... • The contact material and construction are particularly suitable for low voltages • Function of the two change-over contacts switched to trigger signal contact (electrical signals triggering) • Test button for contact function "electric tripping " ...
Check full description
... Please note that the package does not contain lithium battery and USB charger. These can be ordered separately. This product is in conformity with all provisions of Directive EMC 2004/108/EMC and it complies with relevant European ...
... Please note that the package does not contain lithium battery and USB charger. These can be ordered separately. This product is in conformity with all provisions of Directive EMC 2004/108/EMC and it complies with relevant European ...
AN-1215 APPLICATION NOTE
... The AD5370 is a 40-channel, 16-bit DAC available both in 64-lead LFCSP and 64-lead LQFP packages. The AD5370 has two reference input pins. VREF0 is the reference pin for DAC channels VOUT0 to VOUT7. VREF1 is the reference pin for DAC channels VOUT8 to VOUT39. Figure 1 shows a typical configuration f ...
... The AD5370 is a 40-channel, 16-bit DAC available both in 64-lead LFCSP and 64-lead LQFP packages. The AD5370 has two reference input pins. VREF0 is the reference pin for DAC channels VOUT0 to VOUT7. VREF1 is the reference pin for DAC channels VOUT8 to VOUT39. Figure 1 shows a typical configuration f ...
- Muhazam
... • If the displaced electron is freely moving: ELECTRODYNAMIC phenomenon • If the displaced electron is tied-up into material: ELECTROSTATIC phenomenon • What we want to learn in this course is electrodynamic phenomenon ...
... • If the displaced electron is freely moving: ELECTRODYNAMIC phenomenon • If the displaced electron is tied-up into material: ELECTROSTATIC phenomenon • What we want to learn in this course is electrodynamic phenomenon ...
Input Isolation Module
... The Input Isolation Module can be set up with two unipolar inputs or with a single bi-polar input. It provides increased front end surge protection using multiple stages of MOVs, inductors, and Tranzorbs. The Input Isolation Module consists of a plastic, DIN rail-mountable module with two internal c ...
... The Input Isolation Module can be set up with two unipolar inputs or with a single bi-polar input. It provides increased front end surge protection using multiple stages of MOVs, inductors, and Tranzorbs. The Input Isolation Module consists of a plastic, DIN rail-mountable module with two internal c ...
Opto-isolator
In electronics, an opto-isolator, also called an optocoupler, photocoupler, or optical isolator, is a component that transfers electrical signals between two isolated circuits by using light. Opto-isolators prevent high voltages from affecting the system receiving the signal. Commercially available opto-isolators withstand input-to-output voltages up to 10 kV and voltage transients with speeds up to 10 kV/μs.A common type of opto-isolator consists of an LED and a phototransistor in the same opaque package. Other types of source-sensor combinations include LED-photodiode, LED-LASCR, and lamp-photoresistor pairs. Usually opto-isolators transfer digital (on-off) signals, but some techniques allow them to be used with analog signals.