100 KV from a bike - Apparently Apparel
... YOU CAN GET UP TO 100,000 VOLTS DC CURRENT FROM JUST A BICYCLE GENERATOR. A bike generator gives off alternating current (AC) which can be transformed into High Voltage AC or DC currant, Thru the use of a High Voltage Transformer or a Voltage doubler in this case a voltage multiplier. It's very simp ...
... YOU CAN GET UP TO 100,000 VOLTS DC CURRENT FROM JUST A BICYCLE GENERATOR. A bike generator gives off alternating current (AC) which can be transformed into High Voltage AC or DC currant, Thru the use of a High Voltage Transformer or a Voltage doubler in this case a voltage multiplier. It's very simp ...
Your First Radio (8)+(4)+(15)
... What device increases the low-power output from a handheld transceiver? A voltage divider An RF power amplifier An impedance network A voltage regulator ...
... What device increases the low-power output from a handheld transceiver? A voltage divider An RF power amplifier An impedance network A voltage regulator ...
Ohms Law Ohmic Resistors versus Lightbulbs
... The filaments of light bulbs are made of Tungsten, which is a very good conductor. It heats up easily. Tungsten 0.004403 / C at 20C (i.e. To 20C ) ...
... The filaments of light bulbs are made of Tungsten, which is a very good conductor. It heats up easily. Tungsten 0.004403 / C at 20C (i.e. To 20C ) ...
A77-1 / SMA77-1 Cascadable Amplifier 5 to 600 MHz
... The A77-1 RF amplifier is a discrete hybrid design, which incorporates the use of thin film manufacturing processes for accurate performance and high reliability. The single stage silicon bipolar transistor feedback amplifier design displays impressive performance over a broadband frequency range. A ...
... The A77-1 RF amplifier is a discrete hybrid design, which incorporates the use of thin film manufacturing processes for accurate performance and high reliability. The single stage silicon bipolar transistor feedback amplifier design displays impressive performance over a broadband frequency range. A ...
20091119084719!Filter_Instructions
... where Vo/Vi is the gain. Solve this equation for dB = 1/√2 . Now, find the point on the gain portion of the Bode plot where this occurs. To check your answer, this should correspond to a phase response of -45°. Finally, this circuit should display a gain response which falls off 20dB per decade. Con ...
... where Vo/Vi is the gain. Solve this equation for dB = 1/√2 . Now, find the point on the gain portion of the Bode plot where this occurs. To check your answer, this should correspond to a phase response of -45°. Finally, this circuit should display a gain response which falls off 20dB per decade. Con ...
AP8801 500mA LED STEP-DOWN CONVERTER Description
... The recommended method of driving the CTRL pin and controlling the amplitude of the PWM waveform is to use a small NPN switching transistor. This uses the internal pull-up resistor between the CTRL pin and the internal voltage reference to pull-up CTRL pin when the external transistor is turned off. ...
... The recommended method of driving the CTRL pin and controlling the amplitude of the PWM waveform is to use a small NPN switching transistor. This uses the internal pull-up resistor between the CTRL pin and the internal voltage reference to pull-up CTRL pin when the external transistor is turned off. ...
MAX9129 Quad Bus LVDS Driver with Flow-Through Pinout General Description
... In this example, capacitive loading reduces the characteristic impedance from 120Ω to 54Ω. The load seen by a driver located on a card in the middle of the bus is 27Ω because the driver sees two 54Ω loads in parallel. A typical LVDS driver (rated for a 100Ω load) would not develop a large enough dif ...
... In this example, capacitive loading reduces the characteristic impedance from 120Ω to 54Ω. The load seen by a driver located on a card in the middle of the bus is 27Ω because the driver sees two 54Ω loads in parallel. A typical LVDS driver (rated for a 100Ω load) would not develop a large enough dif ...
Magnetic Latch Solenoid Actuator
... Solenoid Actuator, specially designed for reliable long life service in irrigation systems controlled by Battery Operated Controllers. The BERMAD latching Solenoid Actuator is applicable directly to the valve cover or with a 2-Way Base that enables combining it in variety of 2-way control circuits. ...
... Solenoid Actuator, specially designed for reliable long life service in irrigation systems controlled by Battery Operated Controllers. The BERMAD latching Solenoid Actuator is applicable directly to the valve cover or with a 2-Way Base that enables combining it in variety of 2-way control circuits. ...
Chapter 11
... Adding a Capacitor II • With the same supplied voltage, the current draw is less by adding the capacitor. • Since power companies charge more for larger currents because it leads to larger power losses. • Overall, the power factor correction benefits the power company and the consumer. • By choosin ...
... Adding a Capacitor II • With the same supplied voltage, the current draw is less by adding the capacitor. • Since power companies charge more for larger currents because it leads to larger power losses. • Overall, the power factor correction benefits the power company and the consumer. • By choosin ...
WE 286A - Western Electric
... modulation-distortion as the amplification is varied by varying the control-grid bias. The tube is thus especially suitable for use in circuits employing automatic volume control. A separate base terminal is provided for the suppressor grid making possible the use of the tube in various special circ ...
... modulation-distortion as the amplification is varied by varying the control-grid bias. The tube is thus especially suitable for use in circuits employing automatic volume control. A separate base terminal is provided for the suppressor grid making possible the use of the tube in various special circ ...
LT5571 - 620MHz – 1100MHz High Linearity Direct Quadrature Modulator.
... RFID, GSM, EDGE, CDMA, CDMA2000, and other systems. It may also be configured as an image reject upconverting mixer by applying 90° phase-shifted signals to the I and Q inputs. The high impedance I/Q baseband inputs consist of voltage-to-current converters that in turn drive double-balanced mixers. T ...
... RFID, GSM, EDGE, CDMA, CDMA2000, and other systems. It may also be configured as an image reject upconverting mixer by applying 90° phase-shifted signals to the I and Q inputs. The high impedance I/Q baseband inputs consist of voltage-to-current converters that in turn drive double-balanced mixers. T ...
Switched-mode power supply
A switched-mode power supply (switching-mode power supply, switch-mode power supply, SMPS, or switcher) is an electronic power supply that incorporates a switching regulator to convert electrical power efficiently. Like other power supplies, an SMPS transfers power from a source, like mains power, to a load, such as a personal computer, while converting voltage and current characteristics. Unlike a linear power supply, the pass transistor of a switching-mode supply continually switches between low-dissipation, full-on and full-off states, and spends very little time in the high dissipation transitions, which minimizes wasted energy. Ideally, a switched-mode power supply dissipates no power. Voltage regulation is achieved by varying the ratio of on-to-off time. In contrast, a linear power supply regulates the output voltage by continually dissipating power in the pass transistor. This higher power conversion efficiency is an important advantage of a switched-mode power supply. Switched-mode power supplies may also be substantially smaller and lighter than a linear supply due to the smaller transformer size and weight.Switching regulators are used as replacements for linear regulators when higher efficiency, smaller size or lighter weight are required. They are, however, more complicated; their switching currents can cause electrical noise problems if not carefully suppressed, and simple designs may have a poor power factor.