Current-voltage model of LED light sources - VBN
... typically done using three control loops, each controlling different diode color [3]. As red diode is the main contributor for the X tristimulus value color control loop for X controls the red diode. Similarly the Y and Z control loops controls the green and blue diode, respectively. The intensity o ...
... typically done using three control loops, each controlling different diode color [3]. As red diode is the main contributor for the X tristimulus value color control loop for X controls the red diode. Similarly the Y and Z control loops controls the green and blue diode, respectively. The intensity o ...
AN2009-06 MIPAQ™ sense
... Due to technical requirements components may contain dangerous substances. For information on the types in question please contact your nearest Infineon Technologies Office. Infineon Technologies Components may only be used in life-support devices or systems with the express written approval of Infi ...
... Due to technical requirements components may contain dangerous substances. For information on the types in question please contact your nearest Infineon Technologies Office. Infineon Technologies Components may only be used in life-support devices or systems with the express written approval of Infi ...
AN1709 APPLICATION NOTE EMC DESIGN GUIDE FOR ST MICROCONTROLLERS
... DLU Test methodology and characterization: Electro-Static Discharges (one positive then one negative test) are applied to each pin of 3 samples when the microcontroller is running to assess the latch-up performance in dynamic mode. Power supplies are set to the typical values, the oscillator is conn ...
... DLU Test methodology and characterization: Electro-Static Discharges (one positive then one negative test) are applied to each pin of 3 samples when the microcontroller is running to assess the latch-up performance in dynamic mode. Power supplies are set to the typical values, the oscillator is conn ...
FTB 723-1 Equipment Reference Manual P/N
... every practical safety precaution, exercise extreme caution at all times when you expose circuits and components, and when you operate, maintain, or service this equipment. ...
... every practical safety precaution, exercise extreme caution at all times when you expose circuits and components, and when you operate, maintain, or service this equipment. ...
Bates
... Coefficient of Resistance Hot Resistance and Superconductivity There is often a great difference in the amount of resistance a wire has when hot in normal operations and when cold without its normal load current. For example, a typical 100-W incandescent light bulb has a hot resistance of 144 ...
... Coefficient of Resistance Hot Resistance and Superconductivity There is often a great difference in the amount of resistance a wire has when hot in normal operations and when cold without its normal load current. For example, a typical 100-W incandescent light bulb has a hot resistance of 144 ...
Evaluates: MAX1932 MAX1932 Evaluation Kit General Description Features
... pins supplying the CLK_P, CS_P, DIN_P (5V signals), and loopback signal. The CS, SCLK, and DIN pads on the EV kit’s bottom edge are VCC levelshifted signals from the MAX1841 translator. Both signal locations can be used for monitoring. For instructions on selecting the feedback resistors for other o ...
... pins supplying the CLK_P, CS_P, DIN_P (5V signals), and loopback signal. The CS, SCLK, and DIN pads on the EV kit’s bottom edge are VCC levelshifted signals from the MAX1841 translator. Both signal locations can be used for monitoring. For instructions on selecting the feedback resistors for other o ...
AD9631
... The maximum power that can be safely dissipated by these devices is limited by the associated rise in junction temperature. The maximum safe junction temperature for plastic encapsulated devices is determined by the glass transition temperature of the plastic, approximately 150ⴗC. Exceeding this lim ...
... The maximum power that can be safely dissipated by these devices is limited by the associated rise in junction temperature. The maximum safe junction temperature for plastic encapsulated devices is determined by the glass transition temperature of the plastic, approximately 150ⴗC. Exceeding this lim ...
Robust damping of interarea oscillations with unified power
... which can guarantee robust performance and robust stability, despite uncertainty in plant parameter variations, has been applied in power systems to damp out lowfrequency oscillations [5-7]. Normally, the problem is formulated as a weighted mixed-sensitivity design and solved by a Riccati approach. ...
... which can guarantee robust performance and robust stability, despite uncertainty in plant parameter variations, has been applied in power systems to damp out lowfrequency oscillations [5-7]. Normally, the problem is formulated as a weighted mixed-sensitivity design and solved by a Riccati approach. ...
G201 STEP MOTOR DRIVE
... motor’s rated phase current. An unregulated power supply may be used as long as the voltage stays between the limits; keep the ripple voltage to 10% or less for best results. The drive has a 2 second power-on reset time before the motor is energized. CAUTION! Power supply voltage in excess of 80 VDC ...
... motor’s rated phase current. An unregulated power supply may be used as long as the voltage stays between the limits; keep the ripple voltage to 10% or less for best results. The drive has a 2 second power-on reset time before the motor is energized. CAUTION! Power supply voltage in excess of 80 VDC ...
$doc.title
... impedance of the CMOS input stage, makes the TLC2652 and TLC2652A an ideal choice for low-level signal processing applications such as strain gauges, thermocouples, and other transducer amplifiers. For applications that NC − No internal connection require extremely low noise and higher usable bandwi ...
... impedance of the CMOS input stage, makes the TLC2652 and TLC2652A an ideal choice for low-level signal processing applications such as strain gauges, thermocouples, and other transducer amplifiers. For applications that NC − No internal connection require extremely low noise and higher usable bandwi ...
SLI-80 - Cary Audio
... VENTILATION: Slots and openings in the cabinet create ventilation to protect the component from overheating. These openings on the top and bottom panels must remain unobstructed. Allow at least 6 inches (16cm) of clearance above the unit and an opening behind the unit for airflow. Do not place the u ...
... VENTILATION: Slots and openings in the cabinet create ventilation to protect the component from overheating. These openings on the top and bottom panels must remain unobstructed. Allow at least 6 inches (16cm) of clearance above the unit and an opening behind the unit for airflow. Do not place the u ...
1 Purpose and scope 2 Power supply systems
... d) For the supply of facilities that is critical for the traction of trains, no residual current disconnectors shall be used. e) For the supply of facilities that do not influence the traction of trains automatic disconnection in fault condition shall be installed according to [NEK 400] or in other ...
... d) For the supply of facilities that is critical for the traction of trains, no residual current disconnectors shall be used. e) For the supply of facilities that do not influence the traction of trains automatic disconnection in fault condition shall be installed according to [NEK 400] or in other ...
Buck converter
A buck converter is a voltage step down and current step up converter.The simplest way to reduce the voltage of a DC supply is to use a linear regulator (such as a 7805), but linear regulators waste energy as they operate by dissipating excess power as heat. Buck converters, on the other hand, can be remarkably efficient (95% or higher for integrated circuits), making them useful for tasks such as converting the main voltage in a computer (12V in a desktop, 12-24V in a laptop) down to the 0.8-1.8V needed by the processor.