Sendyne Corp. Impact of Current Measurement Offset Error in SOC
... operation of the battery within the manufacturer’s specifications for Depth of Discharge (DOD). Adherence to such specifications is important for the longevity and health of the battery pack as well as for the fuel consumption of an HEV. Because HEV batteries operate in a narrow SOC window (typicall ...
... operation of the battery within the manufacturer’s specifications for Depth of Discharge (DOD). Adherence to such specifications is important for the longevity and health of the battery pack as well as for the fuel consumption of an HEV. Because HEV batteries operate in a narrow SOC window (typicall ...
LT5511 - High Signal Level Upconverting Mixer.
... Oscillator Signal. They can also be driven single-ended by connecting one to an RF ground through a DC blocking capacitor. For single-ended drive, use LO+ for the signal input, as this results in less interference from unwanted coupling of the LO signal to other pins. These pins are internally biase ...
... Oscillator Signal. They can also be driven single-ended by connecting one to an RF ground through a DC blocking capacitor. For single-ended drive, use LO+ for the signal input, as this results in less interference from unwanted coupling of the LO signal to other pins. These pins are internally biase ...
Power on the move
... PASS switchgear has a modular design that allows several elements to be combined. These elements include the circuit breaker, combined disconnector-earthing switch, outdoor SF6/air bushing, slipover current transformers, voltage transformers, cable entry/exit and surge arresters. All PASS solutions ...
... PASS switchgear has a modular design that allows several elements to be combined. These elements include the circuit breaker, combined disconnector-earthing switch, outdoor SF6/air bushing, slipover current transformers, voltage transformers, cable entry/exit and surge arresters. All PASS solutions ...
2.5MHz, 1.5A Synchronous Step Down Regulator
... regulator solution. The input voltage range is 2.9 to 5.5V with either factory programmed outputs from 1.0 to 3.3V or adjustable output via an external resistor divider. The converter operates at fixed 2.5MHz switching frequency allowing small L/C filtering components. The voltage mode architecture ...
... regulator solution. The input voltage range is 2.9 to 5.5V with either factory programmed outputs from 1.0 to 3.3V or adjustable output via an external resistor divider. The converter operates at fixed 2.5MHz switching frequency allowing small L/C filtering components. The voltage mode architecture ...
TS-64WDS - Communications Specialists
... the CTCSS signal, and the High Pass Filter on the TS-64WDS will not be required. In those cases where the High Pass Filter must be utilized, break the discriminator audio path in the receiver just after the point where the TS-64WDS Discriminator Input was connected. Then install the High Pass Filter ...
... the CTCSS signal, and the High Pass Filter on the TS-64WDS will not be required. In those cases where the High Pass Filter must be utilized, break the discriminator audio path in the receiver just after the point where the TS-64WDS Discriminator Input was connected. Then install the High Pass Filter ...
understanding voltage stability - Sacramento
... reactive power or voltage that could lead to voltage collapse. Although the project attempts to start at a basic level, the reader is expected to understand vectors, power flow, and be familiar with how power system elements are modeled. ...
... reactive power or voltage that could lead to voltage collapse. Although the project attempts to start at a basic level, the reader is expected to understand vectors, power flow, and be familiar with how power system elements are modeled. ...
Power Management for AM18xx/AM17xx Processors
... efficiency across the widest possible range of load currents. For low-noise applications, the I2C interface can be used to force the converters into the fixed-frequency PWM mode. The TPS65070 converters allow using small inductors and capacitors to achieve a small solution size. ...
... efficiency across the widest possible range of load currents. For low-noise applications, the I2C interface can be used to force the converters into the fixed-frequency PWM mode. The TPS65070 converters allow using small inductors and capacitors to achieve a small solution size. ...
1. Features •
... For greater precision on safety mode temporarisations and on line diagnosis, connect a RC dipole. Ex: (Rext = 8.66kΩ and Cext = 1nF) to pin H500 in accordance with opposite figure. It must be connected to ground in case it’s not used. ...
... For greater precision on safety mode temporarisations and on line diagnosis, connect a RC dipole. Ex: (Rext = 8.66kΩ and Cext = 1nF) to pin H500 in accordance with opposite figure. It must be connected to ground in case it’s not used. ...
Table of Contents - Northwest Power and Conservation Council
... measured and recorded. Because the substation is usually at the geographic center of the area served, this temperature will usually suffice. However, if significant microclimates are known to exist, temperature monitoring and recording may also be required at the feeder end-of-line locations, so tha ...
... measured and recorded. Because the substation is usually at the geographic center of the area served, this temperature will usually suffice. However, if significant microclimates are known to exist, temperature monitoring and recording may also be required at the feeder end-of-line locations, so tha ...
MAX4490/MAX4491/MAX4492 Low-Cost, High-Slew-Rate, Rail-to-Rail I/O Op Amps in SC70 General Description
... The MAX4490/MAX4491/MAX4492 CMOS operational amplifiers feature class-AB push-pull output stages that can drive a 100kΩ load to within 1.5mV of either supply rail. Short-circuit output current is typically ±50mA. Figures 1a and 1b show the typical temperature dependence of output source and sink cur ...
... The MAX4490/MAX4491/MAX4492 CMOS operational amplifiers feature class-AB push-pull output stages that can drive a 100kΩ load to within 1.5mV of either supply rail. Short-circuit output current is typically ±50mA. Figures 1a and 1b show the typical temperature dependence of output source and sink cur ...
AD7783 数据手册DataSheet下载
... Table I shows the output rms noise and output peak-to-peak resolution in bits (rounded to the nearest 0.5 LSB) for the two input voltage ranges. The numbers are typical and are generated at a differential input voltage of 0 V. The peak-to-peak resolution figures represent the resolution for which th ...
... Table I shows the output rms noise and output peak-to-peak resolution in bits (rounded to the nearest 0.5 LSB) for the two input voltage ranges. The numbers are typical and are generated at a differential input voltage of 0 V. The peak-to-peak resolution figures represent the resolution for which th ...
Hall Effect Devices
... parallel to the lines of force around the magnet. Hall Effect Devices work best at the poles of the magnet where the flux lines are more concentrated. Package types and price The devices included with this course are the cheapest package types. Similar devices come in different packages. The price v ...
... parallel to the lines of force around the magnet. Hall Effect Devices work best at the poles of the magnet where the flux lines are more concentrated. Package types and price The devices included with this course are the cheapest package types. Similar devices come in different packages. The price v ...
Buck converter
A buck converter is a voltage step down and current step up converter.The simplest way to reduce the voltage of a DC supply is to use a linear regulator (such as a 7805), but linear regulators waste energy as they operate by dissipating excess power as heat. Buck converters, on the other hand, can be remarkably efficient (95% or higher for integrated circuits), making them useful for tasks such as converting the main voltage in a computer (12V in a desktop, 12-24V in a laptop) down to the 0.8-1.8V needed by the processor.