AND8129/DA 30 W Power Supply Operating in
... turns a MOSFET ON until its current grows−up to the setpoint to turn it off and then waits until the core reset is detected (usually via an auxiliary winding) to reactivate this transistor. As a result, the controller does not include any standalone clock but only detects the presence of events cond ...
... turns a MOSFET ON until its current grows−up to the setpoint to turn it off and then waits until the core reset is detected (usually via an auxiliary winding) to reactivate this transistor. As a result, the controller does not include any standalone clock but only detects the presence of events cond ...
An Introduction to Electric Power Systems
... well separated from each other, to prevent arcing (sparks) and injury or people or animals. • Why use such high voltages? Using very high voltages on the transmission lines reduces the amount of energy wasted heating up the wires. ...
... well separated from each other, to prevent arcing (sparks) and injury or people or animals. • Why use such high voltages? Using very high voltages on the transmission lines reduces the amount of energy wasted heating up the wires. ...
MODEL 62000P SERIES Programmable DC Power Supply Key Features:
... power supplies provide the same rated current at all output voltages, however, the 62000P provides greater current at lower output voltages. This means both low voltage/high current and high voltage/low current UUTs can be tested using a single supply avoiding the for multiple supplies saving cost a ...
... power supplies provide the same rated current at all output voltages, however, the 62000P provides greater current at lower output voltages. This means both low voltage/high current and high voltage/low current UUTs can be tested using a single supply avoiding the for multiple supplies saving cost a ...
MAX742 Switch-Mode Regulator with +5V to ±12V or ±15V Dual Output _______________General Description
... smallest inductors (where E = 1/2 LI2 is minimum) are realized when operating at the crossover point between continuous and discontinuous modes. Lowering the inductor value further still results in discontinuous current even at full load, which minimizes the output capacitor size required for AC sta ...
... smallest inductors (where E = 1/2 LI2 is minimum) are realized when operating at the crossover point between continuous and discontinuous modes. Lowering the inductor value further still results in discontinuous current even at full load, which minimizes the output capacitor size required for AC sta ...
How can I reduce my standby power consumption?
... consume very little power as long as the input voltage is a definite logic '1' or logic '0'. If they are allowed to float, with no tie to a specific voltage, they will often oscillate spontaneously or sit at a voltage which is neither a definite '1' nor a '0'. In each of these cases, the extra curre ...
... consume very little power as long as the input voltage is a definite logic '1' or logic '0'. If they are allowed to float, with no tie to a specific voltage, they will often oscillate spontaneously or sit at a voltage which is neither a definite '1' nor a '0'. In each of these cases, the extra curre ...
DTMG Rev E
... Display : 3 digits (example : 9.99 mA) Resolution : 3 digits (example : 999 points for Imax = 9.99 mA) Breakdown detection “DELTATEST” detector adjusted for ∆I = 10% of the full scale ± 10% with 10 µsec. ± 20%. Total insensitivity to current due to the resistance and the capacitance of the devic ...
... Display : 3 digits (example : 9.99 mA) Resolution : 3 digits (example : 999 points for Imax = 9.99 mA) Breakdown detection “DELTATEST” detector adjusted for ∆I = 10% of the full scale ± 10% with 10 µsec. ± 20%. Total insensitivity to current due to the resistance and the capacitance of the devic ...
70100009_Product_Information_MI03-X1-80
... components 2A Current controlled output for safety relevant components ...
... components 2A Current controlled output for safety relevant components ...
LM79M05 - Experimentalists Anonymous
... The LM79MXX series of 3-terminal regulators is available with fixed output voltages of −5V, −12V, and −15V. These devices need only one external component — a compensation capacitor at the output. The LM79MXX series is packaged in the TO-220 power package, and is capable of supplying 0.5A of output ...
... The LM79MXX series of 3-terminal regulators is available with fixed output voltages of −5V, −12V, and −15V. These devices need only one external component — a compensation capacitor at the output. The LM79MXX series is packaged in the TO-220 power package, and is capable of supplying 0.5A of output ...
Buck converter
A buck converter is a voltage step down and current step up converter.The simplest way to reduce the voltage of a DC supply is to use a linear regulator (such as a 7805), but linear regulators waste energy as they operate by dissipating excess power as heat. Buck converters, on the other hand, can be remarkably efficient (95% or higher for integrated circuits), making them useful for tasks such as converting the main voltage in a computer (12V in a desktop, 12-24V in a laptop) down to the 0.8-1.8V needed by the processor.