PSM05S93E5-A
... Input drive is High-active type. There is a minimum 3.3kΩ pull-down resistor in the input circuit of IC. To prevent malfunction, the wiring of each input should be as short as possible. When using RC coupling circuit, make sure the input signal level meet the turn-on and turn-off threshold voltage. ...
... Input drive is High-active type. There is a minimum 3.3kΩ pull-down resistor in the input circuit of IC. To prevent malfunction, the wiring of each input should be as short as possible. When using RC coupling circuit, make sure the input signal level meet the turn-on and turn-off threshold voltage. ...
ANNEXURE 1 Technical Specifications for Radio Frequency (RF
... quotation.It shall be duly certified by them, along with supporting documents. Evaluation of the bids will be based on this table. Datasheet from OEM (original equipment manufacturer) shall also include optimum input, output impedances and other relevant parameters for RF amplifier design. ...
... quotation.It shall be duly certified by them, along with supporting documents. Evaluation of the bids will be based on this table. Datasheet from OEM (original equipment manufacturer) shall also include optimum input, output impedances and other relevant parameters for RF amplifier design. ...
Bad_sample_OldMathEqn
... switching means (102a, 102b, 102c, 102d) for controlling the application of electrical power to the first output connection,- at least one floating full bridge circuit (110, 310, 312, 2100, 2104, 2106, 2110), wherein each floating full bridge circuit comprises a capacitor (116) adapted for powering ...
... switching means (102a, 102b, 102c, 102d) for controlling the application of electrical power to the first output connection,- at least one floating full bridge circuit (110, 310, 312, 2100, 2104, 2106, 2110), wherein each floating full bridge circuit comprises a capacitor (116) adapted for powering ...
MAX1698/MAX1698A High-Efficiency Step-Up Current Regulator for LEDs General Description
... low, 300mV current-sense threshold. In the standard configuration, a feedback resistor, RFB, sets the current through the primary chain of LEDs. Additional chains of matching LEDs can be added with an equivalent resistor. In matched LED arrays, the secondary chain currents closely track the primary ...
... low, 300mV current-sense threshold. In the standard configuration, a feedback resistor, RFB, sets the current through the primary chain of LEDs. Additional chains of matching LEDs can be added with an equivalent resistor. In matched LED arrays, the secondary chain currents closely track the primary ...
pn junction diode
... nook and cranny of our existence as does electronics. The p-n junction is at the heart of this technology. Most electronics is silicon based, that is, the devices are made of silicon. Silicon wafers are subjected to special procedures which result in what is called p-type silicon material and n-type ...
... nook and cranny of our existence as does electronics. The p-n junction is at the heart of this technology. Most electronics is silicon based, that is, the devices are made of silicon. Silicon wafers are subjected to special procedures which result in what is called p-type silicon material and n-type ...
exam_01_solution_ake..
... In order to effectively and quickly write the waveform in terms of singularity functions, break it up into pieces and write an equation for each piece. The r(t) represents a ramp. The 2 in front of it is the slope of the ramp, 1/0.5. A positive slope is represented by a positive constant and in cont ...
... In order to effectively and quickly write the waveform in terms of singularity functions, break it up into pieces and write an equation for each piece. The r(t) represents a ramp. The 2 in front of it is the slope of the ramp, 1/0.5. A positive slope is represented by a positive constant and in cont ...
SGM9125 5-Channel, 5th Order, Standard Definition Video Filter
... and buffering SDTV signals in front of video decoder or behind video encoder. For example, SGM9125 can replace five passive LC filters and five amplifier drivers in set-top box and DVD player, this solution can help you save PCB size and production cost, it also improves video signal performance com ...
... and buffering SDTV signals in front of video decoder or behind video encoder. For example, SGM9125 can replace five passive LC filters and five amplifier drivers in set-top box and DVD player, this solution can help you save PCB size and production cost, it also improves video signal performance com ...
Bipolar Transistor -12V -1A VCE(sat);-240mV(max.) PNP Single CPH3
... rise to smoke or fire, or accidents that could cause damage to other property. When designing equipment, adopt safety measures so that these kinds of accidents or events cannot occur. Such measures include but are not limited to protective circuits and error prevention circuits for safe design, redu ...
... rise to smoke or fire, or accidents that could cause damage to other property. When designing equipment, adopt safety measures so that these kinds of accidents or events cannot occur. Such measures include but are not limited to protective circuits and error prevention circuits for safe design, redu ...
12A02MH 数据资料DataSheet下载
... rise to smoke or fire, or accidents that could cause damage to other property. When designing equipment, adopt safety measures so that these kinds of accidents or events cannot occur. Such measures include but are not limited to protective circuits and error prevention circuits for safe design, redu ...
... rise to smoke or fire, or accidents that could cause damage to other property. When designing equipment, adopt safety measures so that these kinds of accidents or events cannot occur. Such measures include but are not limited to protective circuits and error prevention circuits for safe design, redu ...
Power Diodes - Dr. Imtiaz Hussain
... – Severe over voltage / over current may be caused by a diode switching at different points in the circuit using the diode. – Voltage and current exist simultaneously during switching operation of a diode. Therefore, every switching of the diode is associated with some energy loss. At high switching ...
... – Severe over voltage / over current may be caused by a diode switching at different points in the circuit using the diode. – Voltage and current exist simultaneously during switching operation of a diode. Therefore, every switching of the diode is associated with some energy loss. At high switching ...
3-Phase Power Factor Correction, Using Vienna
... frequency below 50 KHz. 6. Any malfunction in control circuit does not manifest itself in short circuit of output or PFC front end. 7. Sinusoidal input currents with Power Factor = 0.997, THD<5% and overall efficiency > 97% are obtainable with current designs. As can be seen, Vienna Rectifier is the ...
... frequency below 50 KHz. 6. Any malfunction in control circuit does not manifest itself in short circuit of output or PFC front end. 7. Sinusoidal input currents with Power Factor = 0.997, THD<5% and overall efficiency > 97% are obtainable with current designs. As can be seen, Vienna Rectifier is the ...
MJD112
... Information in this document is provided solely in connection with ST products. STMicroelectronics NV and its subsidiaries (“ST”) reserve the right to make changes, corrections, modifications or improvements, to this document, and the products and services described herein at any time, without notic ...
... Information in this document is provided solely in connection with ST products. STMicroelectronics NV and its subsidiaries (“ST”) reserve the right to make changes, corrections, modifications or improvements, to this document, and the products and services described herein at any time, without notic ...
Buck converter
A buck converter is a voltage step down and current step up converter.The simplest way to reduce the voltage of a DC supply is to use a linear regulator (such as a 7805), but linear regulators waste energy as they operate by dissipating excess power as heat. Buck converters, on the other hand, can be remarkably efficient (95% or higher for integrated circuits), making them useful for tasks such as converting the main voltage in a computer (12V in a desktop, 12-24V in a laptop) down to the 0.8-1.8V needed by the processor.