MAX2205–MAX2208 RF Power Detectors in UCSP General Description Features
... detector goes to an op amp in an analog GSM powercontrol scheme, or to an ADC in other systems such as TDMA or discrete-time GSM power control. The MAX2205 has high-input impedance for use with high-value resistive tapping from a CDMA power amplifier. This coupling method is the lowest cost and lowe ...
... detector goes to an op amp in an analog GSM powercontrol scheme, or to an ADC in other systems such as TDMA or discrete-time GSM power control. The MAX2205 has high-input impedance for use with high-value resistive tapping from a CDMA power amplifier. This coupling method is the lowest cost and lowe ...
Basis for Kelvin Contacts
... force contact of the drain and through the source lead. The second set of contacts (sense leads) at the drain and source are connected to a voltage measuring instrument. As there is little current flowing in the sense leads, the voltage drop on the sense connections is minimal. The RDS-ON resistance ...
... force contact of the drain and through the source lead. The second set of contacts (sense leads) at the drain and source are connected to a voltage measuring instrument. As there is little current flowing in the sense leads, the voltage drop on the sense connections is minimal. The RDS-ON resistance ...
NB6N239SMNEVB Evaluation Board User's Manual •
... ON Semiconductor and are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any partic ...
... ON Semiconductor and are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any partic ...
ics843001-21.pdf
... Total Power_MAX (3.465V, with all outputs switching) = 589.05mW + 30mW = 619.05mW 2. Junction Temperature. Junction temperature, Tj, is the temperature at the junction of the bond wire and bond pad and directly affects the reliability of the device. The maximum recommended junction temperature for H ...
... Total Power_MAX (3.465V, with all outputs switching) = 589.05mW + 30mW = 619.05mW 2. Junction Temperature. Junction temperature, Tj, is the temperature at the junction of the bond wire and bond pad and directly affects the reliability of the device. The maximum recommended junction temperature for H ...
PM Synchronous Motor Drive
... The Switching control block is used to limit the inverter commutation frequency to a maximum value specified by the user. When using the average-value inverter, the ab current references are sent to the inverter, as well as switching pulses from a slightly modified Switching control block. ...
... The Switching control block is used to limit the inverter commutation frequency to a maximum value specified by the user. When using the average-value inverter, the ab current references are sent to the inverter, as well as switching pulses from a slightly modified Switching control block. ...
Supplementary information
... directly by replacing the 50 -terminated device by an oscilloscope with 50 input impedance. According to the equivalent circuit in Fig. 3(d) the drive voltage is half the value of the open circuit voltage U0 of the source. Lumped-element device without termination The energy consumption of a non- ...
... directly by replacing the 50 -terminated device by an oscilloscope with 50 input impedance. According to the equivalent circuit in Fig. 3(d) the drive voltage is half the value of the open circuit voltage U0 of the source. Lumped-element device without termination The energy consumption of a non- ...
Evidence of Gate Voltage Oscillations during Short Circuit of
... Previous experimental observations conducted thanks to a 6 kA/1.1 kV Non-Destructive Tester (NDT) [15], lead to conclude that there are three major aspects which play an important role in limiting the short circuit robustness of 1.7 kV /1 kA IGBT modules: a) non-negligible external loop stray induct ...
... Previous experimental observations conducted thanks to a 6 kA/1.1 kV Non-Destructive Tester (NDT) [15], lead to conclude that there are three major aspects which play an important role in limiting the short circuit robustness of 1.7 kV /1 kA IGBT modules: a) non-negligible external loop stray induct ...
326/327 Series - Time Delay Relays - Struthers-Dunn
... Timer / Sensor - Time Delay & Sensor Relays 5 - 25 Amp ...
... Timer / Sensor - Time Delay & Sensor Relays 5 - 25 Amp ...
High Stability, Low Noise, Push-Push VFO
... transformer at the combined source output. The signal produced by two identical Clapp oscillators has equal frequencies but they are forced 180° out-of-phase by the connection of the transistor drains. As an innovation of the circuit, the source capacitors of the two oscillators use the same feedbac ...
... transformer at the combined source output. The signal produced by two identical Clapp oscillators has equal frequencies but they are forced 180° out-of-phase by the connection of the transistor drains. As an innovation of the circuit, the source capacitors of the two oscillators use the same feedbac ...
MP1470 - Monolithic Power System
... from overshooting during startup. When the chip starts, the internal circuit generates a softstart voltage (SS) that ramps up from 0V to 1.2V: When SS falls below the internal reference (REF), SS overrides REF so that the error amplifier uses SS as the reference; when SS exceeds REF, the error ampli ...
... from overshooting during startup. When the chip starts, the internal circuit generates a softstart voltage (SS) that ramps up from 0V to 1.2V: When SS falls below the internal reference (REF), SS overrides REF so that the error amplifier uses SS as the reference; when SS exceeds REF, the error ampli ...
TLV7256 - Texas Instruments
... Multiple Top-Side Markings will be inside parentheses. Only one Top-Side Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation of the previous line and the two combined represent the entire Top-Side Marking for that device. I ...
... Multiple Top-Side Markings will be inside parentheses. Only one Top-Side Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation of the previous line and the two combined represent the entire Top-Side Marking for that device. I ...
Buck converter
A buck converter is a voltage step down and current step up converter.The simplest way to reduce the voltage of a DC supply is to use a linear regulator (such as a 7805), but linear regulators waste energy as they operate by dissipating excess power as heat. Buck converters, on the other hand, can be remarkably efficient (95% or higher for integrated circuits), making them useful for tasks such as converting the main voltage in a computer (12V in a desktop, 12-24V in a laptop) down to the 0.8-1.8V needed by the processor.