HMC788ALP2E
... [1] Reference this number when ordering complete evaluation PCB [2] Circuit Board Material: Rogers 4350 ...
... [1] Reference this number when ordering complete evaluation PCB [2] Circuit Board Material: Rogers 4350 ...
HMC361S8G 数据资料DataSheet下载
... Divide-by-2 Static Dividers with InGaP GaAs HBT technology in 8 lead surface mount plastic packages. This device operates from DC (with a square wave input) to 10 GHz input frequency with a single +5V DC supply. The low additive SSB phase noise of -148 dBc/Hz at 100 kHz offset helps the user maintai ...
... Divide-by-2 Static Dividers with InGaP GaAs HBT technology in 8 lead surface mount plastic packages. This device operates from DC (with a square wave input) to 10 GHz input frequency with a single +5V DC supply. The low additive SSB phase noise of -148 dBc/Hz at 100 kHz offset helps the user maintai ...
HMC549MS8G / 549MS8GE
... and Digital Television receivers operating between 40 and 960 MHz. This high dynamic range LNA has been optimized to provide 3.5 dB noise figure and +27 dBm output IP3 from a single supply of +5.0V @ 120 mA. The outputs of this LNA are extremely well balanced, and can be used to drive a differential ...
... and Digital Television receivers operating between 40 and 960 MHz. This high dynamic range LNA has been optimized to provide 3.5 dB noise figure and +27 dBm output IP3 from a single supply of +5.0V @ 120 mA. The outputs of this LNA are extremely well balanced, and can be used to drive a differential ...
Analog Devices HMC903 Datasheet
... The HMC903 is a self-biased GaAs MMIC Low Noise Amplifier which operates between 6 and 18 GHz. This LNA provides 19 dB of small signal gain, 1.6 dB noise figure, and output IP3 of 27 dBm, while requiring only 90 mA from a +3.5 V supply. The P1dB output power of 16 dBm enables the LNA to function as ...
... The HMC903 is a self-biased GaAs MMIC Low Noise Amplifier which operates between 6 and 18 GHz. This LNA provides 19 dB of small signal gain, 1.6 dB noise figure, and output IP3 of 27 dBm, while requiring only 90 mA from a +3.5 V supply. The P1dB output power of 16 dBm enables the LNA to function as ...
Analog Devices Welcomes Hittite Microwave
... These pins are DC coupled and matched to 50 Ohm. Blocking capacitors are required if RF line potential is not equal to 0V. ...
... These pins are DC coupled and matched to 50 Ohm. Blocking capacitors are required if RF line potential is not equal to 0V. ...
Analog Devices Welcomes Hittite Microwave Corporation
... Wideband Amplifier housed in a leadless 4x4 mm plastic surface mount package. The amplifier operates between 1 and 11 GHz, providing up to 16.5 dB of small signal gain, 1.5 dB noise figure, and output IP3 of +30 dBm, while requiring only 55 mA from a +5V supply. The P1dB output power of up to +18 dB ...
... Wideband Amplifier housed in a leadless 4x4 mm plastic surface mount package. The amplifier operates between 1 and 11 GHz, providing up to 16.5 dB of small signal gain, 1.5 dB noise figure, and output IP3 of +30 dBm, while requiring only 55 mA from a +5V supply. The P1dB output power of up to +18 dB ...
guiding microwaves along a Lecher line
... (a) so that the multimeter displays maximum received signal. Slide the shorting jumper (c) on the Lecher line, and insert the Lecher line in the vertical bores of the PVC body (d). Adjust the height of the Lecher line according to the height of the high-frequency diode (see experiment P3.7.4.1) in t ...
... (a) so that the multimeter displays maximum received signal. Slide the shorting jumper (c) on the Lecher line, and insert the Lecher line in the vertical bores of the PVC body (d). Adjust the height of the Lecher line according to the height of the high-frequency diode (see experiment P3.7.4.1) in t ...
Microwave
Microwaves are a form of electromagnetic radiation with wavelengths ranging from as long as one meter to as short as one millimeter; with frequencies between 300 MHz (100 cm) and 300 GHz (0.1 cm). This broad definition includes both UHF and EHF (millimeter waves), and various sources use different boundaries. In all cases, microwave includes the entire SHF band (3 to 30 GHz, or 10 to 1 cm) at minimum, with RF engineering often restricting the range between 1 and 100 GHz (300 and 3 mm).The prefix micro- in microwave is not meant to suggest a wavelength in the micrometer range. It indicates that microwaves are ""small"", compared to waves used in typical radio broadcasting, in that they have shorter wavelengths. The boundaries between far infrared, terahertz radiation, microwaves, and ultra-high-frequency radio waves are fairly arbitrary and are used variously between different fields of study.Beginning at about 40 GHz, the atmosphere becomes less transparent to microwaves, at lower frequencies to absorption from water vapor and at higher frequencies from oxygen. A spectral band structure causes absorption peaks at specific frequencies (see graph at right). Above 100 GHz, the absorption of electromagnetic radiation by Earth's atmosphere is so great that it is in effect opaque, until the atmosphere becomes transparent again in the so-called infrared and optical window frequency ranges.The term microwave also has a more technical meaning in electromagnetics and circuit theory. Apparatus and techniques may be described qualitatively as ""microwave"" when the frequencies used are high enough that wavelengths of signals are roughly the same as the dimensions of the equipment, so that lumped-element circuit theory is inaccurate. As a consequence, practical microwave technique tends to move away from the discrete resistors, capacitors, and inductors used with lower-frequency radio waves. Instead, distributed circuit elements and transmission-line theory are more useful methods for design and analysis. Open-wire and coaxial transmission lines used at lower frequencies are replaced by waveguides and stripline, and lumped-element tuned circuits are replaced by cavity resonators or resonant lines. In turn, at even higher frequencies, where the wavelength of the electromagnetic waves becomes small in comparison to the size of the structures used to process them, microwave techniques become inadequate, and the methods of optics are used.