Glossary of Terms
... Kirchhoff’s current law: Law that states that the sum of the current entering and the sum of the current leaving a junction are equal. Source: pg 14 of the text Kirchhoff’s voltage law: Law that states that the sum of the voltage drops around a circuit equals the total voltage provided from the sou ...
... Kirchhoff’s current law: Law that states that the sum of the current entering and the sum of the current leaving a junction are equal. Source: pg 14 of the text Kirchhoff’s voltage law: Law that states that the sum of the voltage drops around a circuit equals the total voltage provided from the sou ...
PDF
... minimum scale of zero to the maximum of 0.5, in which the impendence network can execute the step-up dc-dc conversion from the input voltage Vin to the dc-link voltage Vdc. In the practical applications, a higher value of D is required to provide a very high boost factor for the low voltage dc energ ...
... minimum scale of zero to the maximum of 0.5, in which the impendence network can execute the step-up dc-dc conversion from the input voltage Vin to the dc-link voltage Vdc. In the practical applications, a higher value of D is required to provide a very high boost factor for the low voltage dc energ ...
Communication and Sensing Circuits on Cellulose
... electromagnetic waves. In receivers, the captured waves are transduced into oscillating voltage and current that are sent toward the input of the receiver itself. In transmitters, on the contrary, the oscillating voltage and current available at its output are converted into waves by the antenna and ...
... electromagnetic waves. In receivers, the captured waves are transduced into oscillating voltage and current that are sent toward the input of the receiver itself. In transmitters, on the contrary, the oscillating voltage and current available at its output are converted into waves by the antenna and ...
ece2201_lab6_modified
... signal source that will be required to drive a low resistance (1kΩ) load. Determine the value of the small-signal output resistance Rout “looking into” the output node vOUT. (assume = 100). Assume CC is a short at signal frequencies. NOTE: Remember when looking for small signal impedance at a node ...
... signal source that will be required to drive a low resistance (1kΩ) load. Determine the value of the small-signal output resistance Rout “looking into” the output node vOUT. (assume = 100). Assume CC is a short at signal frequencies. NOTE: Remember when looking for small signal impedance at a node ...
LV5980MCGEVB_TEST_PROCEDURE.PDF - 1137 KB
... 4.HICCUP Operating Waveforms (OCP) makes the over-current limiter operation further up the current value of the electronic load. ...
... 4.HICCUP Operating Waveforms (OCP) makes the over-current limiter operation further up the current value of the electronic load. ...
Paper Title (use style: paper title)
... bio-mimetic sonar heads and new methodologies for sonar based applications having nature as source of inspiration. The new sonar heads must have wide frequency bandwidth, e.g. from 50 kHz up to 300 kHz, in order to be able to develop new algorithms for object detection, recognition and navigation. T ...
... bio-mimetic sonar heads and new methodologies for sonar based applications having nature as source of inspiration. The new sonar heads must have wide frequency bandwidth, e.g. from 50 kHz up to 300 kHz, in order to be able to develop new algorithms for object detection, recognition and navigation. T ...
Core Technology Group Application Note 5
... A broad range of systems include components with very low resistance/impedance values such as current meters, force measurement devices, temperature sensors, battery/fuel cells, etc. Such impedance values can be in the range of 0.001 ohm to 0.1 ohm (maybe even smaller). In many cases, it is necessar ...
... A broad range of systems include components with very low resistance/impedance values such as current meters, force measurement devices, temperature sensors, battery/fuel cells, etc. Such impedance values can be in the range of 0.001 ohm to 0.1 ohm (maybe even smaller). In many cases, it is necessar ...
RHD5963 - Aeroflex Microelectronic Solutions
... A license from the Department of Commerce may be required prior to the export of this product from the United States. ...
... A license from the Department of Commerce may be required prior to the export of this product from the United States. ...
Designing With TPS7H3301-SP Double Data Rate (DDR) Termination
... A when going from sinking to sourcing the load, this can only occur if we go from all 0s to all 1s, and this condition stays for longer than the inverse of converter bandwidth. For a linear converter with a bandwidth of 80 kHz, this implies about 12.5 µs, and for the switcher with its bandwidth in t ...
... A when going from sinking to sourcing the load, this can only occur if we go from all 0s to all 1s, and this condition stays for longer than the inverse of converter bandwidth. For a linear converter with a bandwidth of 80 kHz, this implies about 12.5 µs, and for the switcher with its bandwidth in t ...
DATASHEET SEARCH SITE | WWW.ALLDATASHEET.COM
... There is no soldering method that is ideal for all IC packages. Wave soldering is often preferred when through-hole and surface mounted components are mixed on one printed-circuit board. However, wave soldering is not always suitable for surface mounted ICs, or for printed-circuits with high populat ...
... There is no soldering method that is ideal for all IC packages. Wave soldering is often preferred when through-hole and surface mounted components are mixed on one printed-circuit board. However, wave soldering is not always suitable for surface mounted ICs, or for printed-circuits with high populat ...
Standing wave ratio
In radio engineering and telecommunications, standing wave ratio (SWR) is a measure of impedance matching of loads to the characteristic impedance of a transmission line or waveguide. Impedance mismatches result in standing waves along the transmission line, and SWR is defined as the ratio of the partial standing wave's amplitude at an antinode (maximum) to the amplitude at a node (minimum) along the line.The SWR is usually thought of in terms of the maximum and minimum AC voltages along the transmission line, thus called the voltage standing wave ratio or VSWR (sometimes pronounced ""viswar""). For example, the VSWR value 1.2:1 denotes an AC voltage due to standing waves along the transmission line reaching a peak value 1.2 times that of the minimum AC voltage along that line. The SWR can as well be defined as the ratio of the maximum amplitude to minimum amplitude of the transmission line's currents, electric field strength, or the magnetic field strength. Neglecting transmission line loss, these ratios are identical.The power standing wave ratio (PSWR) is defined as the square of the VSWR, however this terminology has no physical relation to actual powers involved in transmission.The SWR can be measured with an instrument called an SWR meter. Since SWR is defined relative to the transmission line's characteristic impedance, the SWR meter must be constructed for that impedance; in practice most transmission lines used in these applications are coaxial cables with an impedance of either 50 or 75 ohms. Checking the SWR is a standard procedure in a radio station, for instance, to verify impedance matching of the antenna to the transmission line (and transmitter). Unlike connecting an impedance analyzer (or ""impedance bridge"") directly to the antenna (or other load), the SWR does not measure the actual impedance of the load, but quantifies the magnitude of the impedance mismatch just performing a measurement on the transmitter side of the transmission line.