Circuit Protection Devices
... allow without opening. The current rating of a fuse is always indicated on the fuse. To select the proper fuse, you must know the normal operating current of the circuit. If you wish to protect the circuit from overloads (excessive current), select a fuse rated at 125 percent of the normal circuit c ...
... allow without opening. The current rating of a fuse is always indicated on the fuse. To select the proper fuse, you must know the normal operating current of the circuit. If you wish to protect the circuit from overloads (excessive current), select a fuse rated at 125 percent of the normal circuit c ...
On-chip phase noise measurement, design study in 65 nm CMOS technology
... Author(s) Daniyal Haider. Abstract Jitter is generally defined as a time deviation of the clock waveform from its desired position. The deviation which occurs can be on the leading or lagging side and it can be bounded (deterministic) or unbounded (random). Jitter is a critical specification in the ...
... Author(s) Daniyal Haider. Abstract Jitter is generally defined as a time deviation of the clock waveform from its desired position. The deviation which occurs can be on the leading or lagging side and it can be bounded (deterministic) or unbounded (random). Jitter is a critical specification in the ...
Tube Stages for DACs.. - PEARL
... toggle on or off a Switch which will switch on or off a current of 2mA. With all Bits’ at Zero all switches will be off and the output will be at zero. Switching the MSB on will produce -2mA current and represents basically "digital silence". Switching all other 15 Switches on will add another -2mA ...
... toggle on or off a Switch which will switch on or off a current of 2mA. With all Bits’ at Zero all switches will be off and the output will be at zero. Switching the MSB on will produce -2mA current and represents basically "digital silence". Switching all other 15 Switches on will add another -2mA ...
Avoid Generator and System Damage Due to a Slow Synchronizing
... direction with respect to the reference VSYSTEM and the speed of which is referred to as generator “slip.” Because the circuit breaker takes a finite time to be physically closed after close initiation, the device or operator initiating the close must anticipate the close condition. Depending on the ...
... direction with respect to the reference VSYSTEM and the speed of which is referred to as generator “slip.” Because the circuit breaker takes a finite time to be physically closed after close initiation, the device or operator initiating the close must anticipate the close condition. Depending on the ...
Sepam™ Series 40 Protective Relays
... WARNING indicates a potentially hazardous situation which, if not avoided, could result in death, serious injury or property damage. ...
... WARNING indicates a potentially hazardous situation which, if not avoided, could result in death, serious injury or property damage. ...
+3.0V to+5.5V, 1µA, RS-232/RS-485/422 Multiprotocol Transceivers General Description Features
... All devices incorporate a proprietary low-dropout transmitter output stage and an on-board dual charge pump to allow RS-232 and RS-485/422 compliant performance from a +3V to +5.5V supply. The receivers feature true fail-safe circuitry that guarantees a logichigh receiver output when the receiver in ...
... All devices incorporate a proprietary low-dropout transmitter output stage and an on-board dual charge pump to allow RS-232 and RS-485/422 compliant performance from a +3V to +5.5V supply. The receivers feature true fail-safe circuitry that guarantees a logichigh receiver output when the receiver in ...
MAX9322 LVECL/LVPECL 1:15 Differential Divide-by-1/Divide-by-2 Clock Driver General Description
... reproduces or divides one of two differential input clocks at 15 differential outputs. An input multiplexer selects from one of two input clocks with input switching frequency in excess of 1.0GHz. The 15 outputs are arranged in four banks with 2, 3, 4, and 6 outputs, respectively. Each output bank i ...
... reproduces or divides one of two differential input clocks at 15 differential outputs. An input multiplexer selects from one of two input clocks with input switching frequency in excess of 1.0GHz. The 15 outputs are arranged in four banks with 2, 3, 4, and 6 outputs, respectively. Each output bank i ...
Solution Description
... uses solar energy, fuel, and mains as power sources. This document describes the PowerCube 1000 in terms of its position, features, architecture, and system description. This document covers the features of PowerCube 1000 V300R002C00, PowerCube 1000 V300R002C01, PowerCube 1000 V300R002C03, PowerCube ...
... uses solar energy, fuel, and mains as power sources. This document describes the PowerCube 1000 in terms of its position, features, architecture, and system description. This document covers the features of PowerCube 1000 V300R002C00, PowerCube 1000 V300R002C01, PowerCube 1000 V300R002C03, PowerCube ...
[Earl_Gates,_Leo_Chartrand
... Publisher does not warrant or guarantee any of the products described herein or perform any independent analysis in connection with any of the product information contained herein. Publisher does not assume, and expressly disclaims, any obligation to obtain and include information other than that pr ...
... Publisher does not warrant or guarantee any of the products described herein or perform any independent analysis in connection with any of the product information contained herein. Publisher does not assume, and expressly disclaims, any obligation to obtain and include information other than that pr ...
STM690T/S/R
... the reset output. Reset remains asserted as long as MR is low and for trec after MR returns high. This active-low input has an internal pull-up. It can be driven from a TTL or CMOS logic line, or shorted to ground with a switch. Leave open if unused. WDI (Watchdog Input). If WDI remains high or low ...
... the reset output. Reset remains asserted as long as MR is low and for trec after MR returns high. This active-low input has an internal pull-up. It can be driven from a TTL or CMOS logic line, or shorted to ground with a switch. Leave open if unused. WDI (Watchdog Input). If WDI remains high or low ...
Piezo Film Sensors Technical Manual
... detectable signal. Common-mode rejection can be used to isolate either very low frequency mechanical strain from simultaneous pyro-effects or vice-versa. These straight-forward techniques are quite familiar to MSI applications engineers who are available for design assistance. ...
... detectable signal. Common-mode rejection can be used to isolate either very low frequency mechanical strain from simultaneous pyro-effects or vice-versa. These straight-forward techniques are quite familiar to MSI applications engineers who are available for design assistance. ...
LTM4601A/LTM4601A-1 - 12A DC/DC uModules with PLL, Output Tracking and Margining
... above 2V and below INTVCC. See the Applications Information section. TRACK/SS (Pin A9): Output Voltage Tracking and SoftStart Pin. When the module is configured as a master output, then a soft-start capacitor is placed on this pin to ground to control the master ramp rate. A soft-start capacitor can ...
... above 2V and below INTVCC. See the Applications Information section. TRACK/SS (Pin A9): Output Voltage Tracking and SoftStart Pin. When the module is configured as a master output, then a soft-start capacitor is placed on this pin to ground to control the master ramp rate. A soft-start capacitor can ...