Click here to Paper Template
... The output of sample and hold circuit (Vr1+, Vr2+, Vr1-, Vr2-,) are concerted to current with the voltage to current converter shown in Figure 6 (a). The circuit consists of differential inputs that are connected to differential outputs from S/H Vrx+ and Vrx-. The differential input controls the out ...
... The output of sample and hold circuit (Vr1+, Vr2+, Vr1-, Vr2-,) are concerted to current with the voltage to current converter shown in Figure 6 (a). The circuit consists of differential inputs that are connected to differential outputs from S/H Vrx+ and Vrx-. The differential input controls the out ...
9- and 11-Channel, Muxed Input LCD Reference Buffers AD8509/AD8511
... that are used to select between two different reference voltages set up by an external resistor ladder. Input bias currents are orders of magnitude less than competitive parts. This allows very large resistor ladders to be used to save supply current. A guaranteed value of 50 nA is much higher than ...
... that are used to select between two different reference voltages set up by an external resistor ladder. Input bias currents are orders of magnitude less than competitive parts. This allows very large resistor ladders to be used to save supply current. A guaranteed value of 50 nA is much higher than ...
LM723QML Voltage Regulator (Rev. A)
... Figure 18. Positive Voltage Regulator - (External NPN Pass Transistor) Table 5. Positive Voltage Regulator - (External NPN Pass Transistor) ...
... Figure 18. Positive Voltage Regulator - (External NPN Pass Transistor) Table 5. Positive Voltage Regulator - (External NPN Pass Transistor) ...
MAX2644 2.4GHz SiGe, High IP3 Low-Noise Amplifier General Description
... Table 2. MAX2644 Typical Scattering Parameters (RBIAS = 1.2kΩ, VCC = +3.0V, TA = +25°C.) FREQ. (MHz) ...
... Table 2. MAX2644 Typical Scattering Parameters (RBIAS = 1.2kΩ, VCC = +3.0V, TA = +25°C.) FREQ. (MHz) ...
introduction
... The above figure shows a VFC-FVC arrangement for transmitting analog information in isolated form. VI is usually a transducer signal that is amplified by Instrumentation amplifier. VFC converts VI to train of current pulses for LED, the phototransistor reconstructs the pulse train at the receiving e ...
... The above figure shows a VFC-FVC arrangement for transmitting analog information in isolated form. VI is usually a transducer signal that is amplified by Instrumentation amplifier. VFC converts VI to train of current pulses for LED, the phototransistor reconstructs the pulse train at the receiving e ...
MAX870/MAX871 Switched-Capacitor Voltage Inverters General Description Features
... In the circuit of Figure 6, capacitors C1 and C2 form the inverter, while C3 and C4 form the doubler. C1 and C3 are the pump capacitors; C2 and C4 are the reservoir capacitors. Because both the inverter and doubler use part of the charge-pump circuit, loading either output causes both outputs to dec ...
... In the circuit of Figure 6, capacitors C1 and C2 form the inverter, while C3 and C4 form the doubler. C1 and C3 are the pump capacitors; C2 and C4 are the reservoir capacitors. Because both the inverter and doubler use part of the charge-pump circuit, loading either output causes both outputs to dec ...
Ultra-Precision CML AnyGate with Internal Input and Output
... 4. The device is not guaranteed to function outside its operating ratings. 5. Due to the limited drive capability use for input of the same package only. 6. Package thermal resistance assumes exposed pad is soldered (or equivalent) to the devices most negative potential on the PCB. ΨJB uses 4-layer ...
... 4. The device is not guaranteed to function outside its operating ratings. 5. Due to the limited drive capability use for input of the same package only. 6. Package thermal resistance assumes exposed pad is soldered (or equivalent) to the devices most negative potential on the PCB. ΨJB uses 4-layer ...
AN113 - Power Conversion, Measurement and Pulse Circuits
... output. Feedback to the regulator stabilizes the loop and the RC at the VC pin provides frequency compensation. The 100k path from L1 bootstraps Q1’s gate drive to about 10V, ensuring saturation.3 The output connected 300Ω-diode combination provides short-circuit protection by shutting down the LT11 ...
... output. Feedback to the regulator stabilizes the loop and the RC at the VC pin provides frequency compensation. The 100k path from L1 bootstraps Q1’s gate drive to about 10V, ensuring saturation.3 The output connected 300Ω-diode combination provides short-circuit protection by shutting down the LT11 ...
multisim
... 1. Construct a three-input combinational circuit for f = m (2, 4, 5, 7) with the aid of Multisim. Show and explain all the steps in details. 2. Design a four-input combinational circuit for f = m (0, 2, 4, 6, 9, 12, 14) with the aid of Multisim. Show and explain all the steps in details. 3. AB repre ...
... 1. Construct a three-input combinational circuit for f = m (2, 4, 5, 7) with the aid of Multisim. Show and explain all the steps in details. 2. Design a four-input combinational circuit for f = m (0, 2, 4, 6, 9, 12, 14) with the aid of Multisim. Show and explain all the steps in details. 3. AB repre ...
INA133 数据资料 dataSheet 下载
... The information provided herein is believed to be reliable; however, BURR-BROWN assumes no responsibility for inaccuracies or omissions. BURR-BROWN assumes no responsibility for the use of this information, and all use of such information shall be entirely at the user’s own risk. Prices and specific ...
... The information provided herein is believed to be reliable; however, BURR-BROWN assumes no responsibility for inaccuracies or omissions. BURR-BROWN assumes no responsibility for the use of this information, and all use of such information shall be entirely at the user’s own risk. Prices and specific ...
AMS2905 数据手册DataSheet 下载
... Note 1: Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. For guaranteed specifications and test conditions, see the Electrical Characteristics. The guaranteed specifications apply only for the test conditions listed. Note 2: Line and Load regulation are guarantee ...
... Note 1: Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. For guaranteed specifications and test conditions, see the Electrical Characteristics. The guaranteed specifications apply only for the test conditions listed. Note 2: Line and Load regulation are guarantee ...
45 An OR Operation In this example an OR operation is used in
... this example the timer has been set for 5 seconds. When S1 is closed, TR1 begins timing. When 5 seconds have elapsed, TR1 will close its associated normally open TR1 contacts, illuminating pilot light PL1. When S1 is open, deenergizing TR1, the TR1 contacts open, immediately extinguishing PL1. This ...
... this example the timer has been set for 5 seconds. When S1 is closed, TR1 begins timing. When 5 seconds have elapsed, TR1 will close its associated normally open TR1 contacts, illuminating pilot light PL1. When S1 is open, deenergizing TR1, the TR1 contacts open, immediately extinguishing PL1. This ...
