FEATURES 2.5V ULTRA-PRECISION 1:4 LVDS Precision Edge FANOUT BUFFER/TRANSLATOR
... LVDS Differential (Outputs): Normally terminated with 100Ω across the pair (Q, /Q). See “LVDS Outputs” section, Figure 2a. Unused outputs should be terminated with a 100Ω resistor across each pair. ...
... LVDS Differential (Outputs): Normally terminated with 100Ω across the pair (Q, /Q). See “LVDS Outputs” section, Figure 2a. Unused outputs should be terminated with a 100Ω resistor across each pair. ...
A 3 BITS DISCRETE PURE LINEAR ANALOG PREPROCESSING FOLDING
... The target of a folding A/D converter is to form the residue signal with simple analog circuits, thereby obviating the need for the coarse quantizer, the DAC, and the subtracter of subranging ADC. In such an implementation (figure 1a), the low dynamic-range residue signal generated by the analog fol ...
... The target of a folding A/D converter is to form the residue signal with simple analog circuits, thereby obviating the need for the coarse quantizer, the DAC, and the subtracter of subranging ADC. In such an implementation (figure 1a), the low dynamic-range residue signal generated by the analog fol ...
S8VK-G (15/30/60/120/240/480-W Models)
... 100 to 240 VAC (85 to 264 VAC) • DC input can be available: 90 to 350 VDC • Possible for 2 phases input usage. • Wide operation temperature range: –40 to 70 °C • Power Boost function at 120% ...
... 100 to 240 VAC (85 to 264 VAC) • DC input can be available: 90 to 350 VDC • Possible for 2 phases input usage. • Wide operation temperature range: –40 to 70 °C • Power Boost function at 120% ...
FEATURES DESCRIPTION D
... This integrated circuit can be damaged by ESD. Texas Instruments recommends that all integrated circuits be handled with appropriate precautions. Failure to observe proper handling and installation procedures can cause damage. ESD damage can range from subtle performance degradation to complete devi ...
... This integrated circuit can be damaged by ESD. Texas Instruments recommends that all integrated circuits be handled with appropriate precautions. Failure to observe proper handling and installation procedures can cause damage. ESD damage can range from subtle performance degradation to complete devi ...
www.BDTIC.com/TI Implications of Slow or Floating CMOS Inputs SCBA004C
... With increased speed, logic devices have become more sensitive to slow input edge rates. A slow input edge rate, coupled with the noise generated on the power rails when the output switches, can cause excessive output errors or oscillations. Similar situations can occur if an unused input is left fl ...
... With increased speed, logic devices have become more sensitive to slow input edge rates. A slow input edge rate, coupled with the noise generated on the power rails when the output switches, can cause excessive output errors or oscillations. Similar situations can occur if an unused input is left fl ...
OPA2677 Dual, Wideband, High Output Current Operational Amplifier FEATURES
... NOTES: (1) Stresses above these ratings may cause permanent damage. Exposure to absolute maximum conditions for extended periods may degrade device reliability. (2) Pins 2 and 6 on SO-8 and HSOP-8 packages, and pins 2 and 11 on QFN-16 package > 500V HBM. ...
... NOTES: (1) Stresses above these ratings may cause permanent damage. Exposure to absolute maximum conditions for extended periods may degrade device reliability. (2) Pins 2 and 6 on SO-8 and HSOP-8 packages, and pins 2 and 11 on QFN-16 package > 500V HBM. ...
Per unit Calculation and Modeling of Apparatus
... For a synchronous machine positive and negative sequence impedances cannot be equal. In case of a synchronous machine, negative sequence currents create a rotating mmf in opposite direction to the rotor mmf. Double frequency emf and currents are induced in rotor. Negative sequence impedance is 70-95 ...
... For a synchronous machine positive and negative sequence impedances cannot be equal. In case of a synchronous machine, negative sequence currents create a rotating mmf in opposite direction to the rotor mmf. Double frequency emf and currents are induced in rotor. Negative sequence impedance is 70-95 ...
MAX3804 12.5Gbps Settable Receive Equalizer General Description Features
... The MAX3804 equalizer is intended for use at the receive end of an FR-4 PC board transmission line, typically up to 30in of differential 6-mil stripline or microstrip. It is specifically designed to mitigate intersymbol interference caused by the frequencydependent path loss of FR-4 transmission lin ...
... The MAX3804 equalizer is intended for use at the receive end of an FR-4 PC board transmission line, typically up to 30in of differential 6-mil stripline or microstrip. It is specifically designed to mitigate intersymbol interference caused by the frequencydependent path loss of FR-4 transmission lin ...
ADL5315 数据手册DataSheet 下载
... temperature and is independent of input current. When using SREF to set the input voltage, a capacitor should be placed between SREF and ground to filter noise from SREF as well as improve power supply rejection over frequency. A value of 2.2 nF, for example, combined with the 20 kΩ output resistanc ...
... temperature and is independent of input current. When using SREF to set the input voltage, a capacitor should be placed between SREF and ground to filter noise from SREF as well as improve power supply rejection over frequency. A value of 2.2 nF, for example, combined with the 20 kΩ output resistanc ...
BUF602 数据资料 dataSheet 下载
... Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. All trademarks are the property of their respective owners. ...
... Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. All trademarks are the property of their respective owners. ...
