
MAX8869 1A, Microcap, Low-Dropout, Linear Regulator General Description
... The MAX8869 features a 4A current limit when the output voltage is in regulation. When the output voltage drops by 8% below its nominal, the current limit folds back to 1.7A. The output can be shorted to ground for an indefinite period of time without damaging the device. Avoid continuous output cur ...
... The MAX8869 features a 4A current limit when the output voltage is in regulation. When the output voltage drops by 8% below its nominal, the current limit folds back to 1.7A. The output can be shorted to ground for an indefinite period of time without damaging the device. Avoid continuous output cur ...
FAN23SV60 TinyBuck™ 10 A Integrated Synchronous Buck Regulator F AN2
... Switching frequency and over-current protection can be programmed to provide a flexible solution for various applications. Output over-voltage, undervoltage, over-current, and thermal shutdown protections help prevent damage to the device during fault conditions. After thermal shutdown is activated, ...
... Switching frequency and over-current protection can be programmed to provide a flexible solution for various applications. Output over-voltage, undervoltage, over-current, and thermal shutdown protections help prevent damage to the device during fault conditions. After thermal shutdown is activated, ...
7872A Data Sheet 08_29_12 Rev 2.fm
... Maxwell Technologies’ 7872A high-speed 14-bit ADC microcircuit features a greater than 100 krad (Si) total dose tolerance; depending upon orbit. The 7872A consists of a track/ hold amplifier, successive-approximation ADC, 3V buried Zener reference and versatile interface logic. It features a selfcon ...
... Maxwell Technologies’ 7872A high-speed 14-bit ADC microcircuit features a greater than 100 krad (Si) total dose tolerance; depending upon orbit. The 7872A consists of a track/ hold amplifier, successive-approximation ADC, 3V buried Zener reference and versatile interface logic. It features a selfcon ...
PDF
... comparison between the leakage current of the OFF Transistors and the switching current of the ON transistors of the pull down network to control the PMOS keeper transistor,yielding reduction of the contention between keeper transistor and the pull down network from which previously proposed techniq ...
... comparison between the leakage current of the OFF Transistors and the switching current of the ON transistors of the pull down network to control the PMOS keeper transistor,yielding reduction of the contention between keeper transistor and the pull down network from which previously proposed techniq ...
LTC1540 - Nanopower Comparator with Reference
... The internal bandgap reference has a voltage of 1.182V referenced to V –. The reference accuracy is ±2.0% from 0°C to 70°C. It can source up to 1mA and sink up to 10µA with a 5V supply. The reference can drive a bypass capacitor of up to 0.01µF without oscillation and by inserting a series resistor, ...
... The internal bandgap reference has a voltage of 1.182V referenced to V –. The reference accuracy is ±2.0% from 0°C to 70°C. It can source up to 1mA and sink up to 10µA with a 5V supply. The reference can drive a bypass capacitor of up to 0.01µF without oscillation and by inserting a series resistor, ...
USB 4-Channel, 24-bit Universal Analog Input Device
... Do not mix hazardous voltage circuits and human-accessible circuits on the same device. Make sure that devices and circuits connected to the USB-2404-UI are properly insulated from human contact. When device terminals are hazardous voltage LIVE (>42.4Vpk/60 VDC), ensure that devices and circuits con ...
... Do not mix hazardous voltage circuits and human-accessible circuits on the same device. Make sure that devices and circuits connected to the USB-2404-UI are properly insulated from human contact. When device terminals are hazardous voltage LIVE (>42.4Vpk/60 VDC), ensure that devices and circuits con ...
Action PAK ®
... counters (DTL, TTL, CMOS). The AP7501 can be used to drive electromechanical counters when connected to an external AC or DC power source. In the AP7501, the DPDT relay contacts are pulsed (closed) for only a short duration (100 milliseconds) for compatibility with standard electromechanical counter ...
... counters (DTL, TTL, CMOS). The AP7501 can be used to drive electromechanical counters when connected to an external AC or DC power source. In the AP7501, the DPDT relay contacts are pulsed (closed) for only a short duration (100 milliseconds) for compatibility with standard electromechanical counter ...
Chapter 4 Powerpoint
... SANs (Storage Area Networks) • A SAN is a network of storage devices that communicate directly with each other and with other ...
... SANs (Storage Area Networks) • A SAN is a network of storage devices that communicate directly with each other and with other ...
BDTIC www.BDTIC.com/infineon TLE4966-3K
... Instruments®, PowerPAD™, C62x™, C55x™, VLYNQ™, Telogy Software™, TMS320C62x™, Code Composer Studio™, SSI™ of Texas Instruments Incorporated. Bluetooth® of Bluetooth SIG, Inc. IrDA® of the Infrared Data Association. Java™, SunOS™, Solaris™ of Sun Microsystems, Inc. Philips®, I2C-Bus® of Koninklijke P ...
... Instruments®, PowerPAD™, C62x™, C55x™, VLYNQ™, Telogy Software™, TMS320C62x™, Code Composer Studio™, SSI™ of Texas Instruments Incorporated. Bluetooth® of Bluetooth SIG, Inc. IrDA® of the Infrared Data Association. Java™, SunOS™, Solaris™ of Sun Microsystems, Inc. Philips®, I2C-Bus® of Koninklijke P ...
TPA2000D2 数据资料 dataSheet 下载
... sensitive circuit is greater than 1 MHz. This is good for circuits that just have to pass FCC and CE because FCC and CE only test radiated emissions greater than 30 MHz. If choosing a ferrite bead, choose one with high impedance at high frequencies, but very low impedance at low frequencies. Use an ...
... sensitive circuit is greater than 1 MHz. This is good for circuits that just have to pass FCC and CE because FCC and CE only test radiated emissions greater than 30 MHz. If choosing a ferrite bead, choose one with high impedance at high frequencies, but very low impedance at low frequencies. Use an ...