Design of a high performance CMOS charge pump for phase
... a rail-to-rail operational amplifier is an ideal choice. The railto-rail operational amplifier shown in Fig. 5 is used in the proposed CP structure. The couples of input transistors are composed by a pair of NMOS devices and a pair of PMOS devices, so as to achieve a wider range of input voltage. Th ...
... a rail-to-rail operational amplifier is an ideal choice. The railto-rail operational amplifier shown in Fig. 5 is used in the proposed CP structure. The couples of input transistors are composed by a pair of NMOS devices and a pair of PMOS devices, so as to achieve a wider range of input voltage. Th ...
FEATURES APPLICATIONS DESCRIPTION
... These pins are used to sense the inductor phase current. Inductor current can be sensed with an external current sense resistor or by using an external R-C circuit and the inductor's DC resistance. The traces for these signals must be connected directly at the current sense element. See Layout Guide ...
... These pins are used to sense the inductor phase current. Inductor current can be sensed with an external current sense resistor or by using an external R-C circuit and the inductor's DC resistance. The traces for these signals must be connected directly at the current sense element. See Layout Guide ...
to this file: /unr15-25w
... which is similar to that achieved by pulling the On/Off Control low, the output voltage quickly drops as the output capacitors discharge into the load. Since there is no longer any output current, the overcurrent detection circuit is released, allowing the soft-start circuit to recharge and the conv ...
... which is similar to that achieved by pulling the On/Off Control low, the output voltage quickly drops as the output capacitors discharge into the load. Since there is no longer any output current, the overcurrent detection circuit is released, allowing the soft-start circuit to recharge and the conv ...
MSC1210-DAQ-EVM Guide
... It is important to operate this EVM within the analog input voltage range of 0V to 3.3V. The output voltage range is 3.3V. The EVM derives power from the RS232 port. Exceeding the specified input range may cause unexpected operation and/or irreversible damage to the EVM. If there are questions conce ...
... It is important to operate this EVM within the analog input voltage range of 0V to 3.3V. The output voltage range is 3.3V. The EVM derives power from the RS232 port. Exceeding the specified input range may cause unexpected operation and/or irreversible damage to the EVM. If there are questions conce ...
LP2985LV-N Micropower 150 mA Low-Noise Low-Dropout Regulator in SOT-23 and
... This could cause problems if a 2.2 µF capacitor were used on the output since it will drop down to approximately 1 µF at high ambient temperatures (which could cause the LP2985LV-N to oscillate). If Z5U or Y5V capacitors are used on the output, a minimum capacitance value of 4.7 µF must be observed. ...
... This could cause problems if a 2.2 µF capacitor were used on the output since it will drop down to approximately 1 µF at high ambient temperatures (which could cause the LP2985LV-N to oscillate). If Z5U or Y5V capacitors are used on the output, a minimum capacitance value of 4.7 µF must be observed. ...
STLC3055N
... generate the negative battery by means of an on chip DC/DC converter controller that drives an external MOS switch. The battery level is properly adjusted depending on the operating mode. A useful characteristic for these applications is the integrated ringing generator. The control interface is a p ...
... generate the negative battery by means of an on chip DC/DC converter controller that drives an external MOS switch. The battery level is properly adjusted depending on the operating mode. A useful characteristic for these applications is the integrated ringing generator. The control interface is a p ...
Honors_Physics_-_Parallel_Circuits_Lab
... 5. In a parallel circuit if a coulomb was traveling through, do you think they would encounter MORE or LESS resistance than a series circuit and WHY? ...
... 5. In a parallel circuit if a coulomb was traveling through, do you think they would encounter MORE or LESS resistance than a series circuit and WHY? ...
OPA699: Wideband, High Gain Voltage Limiting Amplifier (Rev. B)
... (6) I VH (VH bias current) is negative, and IVL (VL bias current) is positive, under these conditions. See Note 3 and Figures 2 and 12. (7) Limiter feedthrough is the ratio of the output magnitude to the sinewave added to V H (or V L) when VIN = 0. (8) VH slew rate conditions are: VIN = VCM +0.4V, G ...
... (6) I VH (VH bias current) is negative, and IVL (VL bias current) is positive, under these conditions. See Note 3 and Figures 2 and 12. (7) Limiter feedthrough is the ratio of the output magnitude to the sinewave added to V H (or V L) when VIN = 0. (8) VH slew rate conditions are: VIN = VCM +0.4V, G ...
SN75196 数据资料 dataSheet 下载
... Low-level output current, IOL (Receiver) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 mA Continuous total power dissipation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . See Dissipation Rating Table Electrostat ...
... Low-level output current, IOL (Receiver) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 mA Continuous total power dissipation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . See Dissipation Rating Table Electrostat ...
MAX9010–MAX9013 SC70, 5ns, Low-Power, Single-Supply, Precision TTL Comparators General Description
... Note 4: Although Common-Mode Input Voltage Range is restricted to -0.2V ≤ VCM ≤ (VCC - 1.9V), either or both inputs can go to either absolute maximum voltage limit, i.e., from -0.3V to (VCC + 0.3V), without damage. The comparator will make a correct (and fast) logic decision provided that at least o ...
... Note 4: Although Common-Mode Input Voltage Range is restricted to -0.2V ≤ VCM ≤ (VCC - 1.9V), either or both inputs can go to either absolute maximum voltage limit, i.e., from -0.3V to (VCC + 0.3V), without damage. The comparator will make a correct (and fast) logic decision provided that at least o ...
LT1246/LT1247 - 1MHz Off-Line Current Mode PWM and DC/DC
... RS In certain applications such as high power regulators it may be desirable to limit the maximum threshold voltage to less than 1V in order to limit the power dissipated in the sense resistor or to limit the short-circuit current of the regulator circuit. This can be accomplished by clamping the ou ...
... RS In certain applications such as high power regulators it may be desirable to limit the maximum threshold voltage to less than 1V in order to limit the power dissipated in the sense resistor or to limit the short-circuit current of the regulator circuit. This can be accomplished by clamping the ou ...
