Application Note 9017 Manufacturing Technology of a Small Capacity Inverter CONTENTS
... capacities over 10[A], it is best not to use this method because accuracy falls for lower resistance levels. Noise, similar to the operating frequency, appears on the detection signal in normal inverter operation. In this case, the amplitude of noise is relatively large because the voltage across th ...
... capacities over 10[A], it is best not to use this method because accuracy falls for lower resistance levels. Noise, similar to the operating frequency, appears on the detection signal in normal inverter operation. In this case, the amplitude of noise is relatively large because the voltage across th ...
AD7839 数据手册DataSheet 下载
... outputs are switched to the externally set potential on the relevant DUTGND pin. The contents of input registers and DAC registers A to H are not affected when the CLR pin is taken low. When CLR is brought back high, the DAC outputs revert to their original outputs as determined by the data in their ...
... outputs are switched to the externally set potential on the relevant DUTGND pin. The contents of input registers and DAC registers A to H are not affected when the CLR pin is taken low. When CLR is brought back high, the DAC outputs revert to their original outputs as determined by the data in their ...
AN2640
... 10-bit A/D Converter with 7 channels and the possibility to use an amplifier (fixed gain 8) between the input and converter ...
... 10-bit A/D Converter with 7 channels and the possibility to use an amplifier (fixed gain 8) between the input and converter ...
Op-Amp Circuits
... The op-amp has two inputs, an inverting input (-) and a non-inverting input (+), and one output. The output goes positive when the non-inverting input (+) goes more positive than the inverting (-) input, and vice versa. The symbols + and – do not mean that that you have to keep one positive with ...
... The op-amp has two inputs, an inverting input (-) and a non-inverting input (+), and one output. The output goes positive when the non-inverting input (+) goes more positive than the inverting (-) input, and vice versa. The symbols + and – do not mean that that you have to keep one positive with ...
REF191 数据手册DataSheet 下载
... The REF19x series precision band gap voltage references use a patented temperature drift curvature correction circuit and laser trimming of highly stable, thin-film resistors to achieve a very low temperature coefficient and high initial accuracy. The REF19x series is made up of micropower, low drop ...
... The REF19x series precision band gap voltage references use a patented temperature drift curvature correction circuit and laser trimming of highly stable, thin-film resistors to achieve a very low temperature coefficient and high initial accuracy. The REF19x series is made up of micropower, low drop ...
SP339 数据资料DataSheet下载
... may be necessary for accurate RS-485/422 communication, but must be removed when the lines are used for RS-232. SP339 provides an elegant solution to this problem by integrating the termination resistor and switching control, and allowing it to be switched in and out of the circuit with a single pin ...
... may be necessary for accurate RS-485/422 communication, but must be removed when the lines are used for RS-232. SP339 provides an elegant solution to this problem by integrating the termination resistor and switching control, and allowing it to be switched in and out of the circuit with a single pin ...
Charles Proteus Steinmetz
... C 3 j4 5∠53.13°, then C* 3 j4 5∠53.13°. Calculators for AC Analysis The analysis of ac circuits involves a considerable amount of complex number arithmetic; thus, you will need a calculator that can work easily with complex numbers. There are several inexpensive calculators on the marke ...
... C 3 j4 5∠53.13°, then C* 3 j4 5∠53.13°. Calculators for AC Analysis The analysis of ac circuits involves a considerable amount of complex number arithmetic; thus, you will need a calculator that can work easily with complex numbers. There are several inexpensive calculators on the marke ...
Low-Dropout 0.5-A Negative Linear Regulator
... VOUTS to VOUT gives the proper output voltage with respect to ground. The UCC284–ADJ can be programmed for any output voltage between –1.25 V and –15 V. This is easily accomplished with the addition of an external resistor divider connected between GND and VOUT with VOUTS connected to the center tap ...
... VOUTS to VOUT gives the proper output voltage with respect to ground. The UCC284–ADJ can be programmed for any output voltage between –1.25 V and –15 V. This is easily accomplished with the addition of an external resistor divider connected between GND and VOUT with VOUTS connected to the center tap ...
100 MHz to 6 GHz TruPwr™ Detector ADL5500
... and +85°C vs. +25°C Linear Reference, Frequency 2700 MHz, Supply 5.0 V ...
... and +85°C vs. +25°C Linear Reference, Frequency 2700 MHz, Supply 5.0 V ...
Accurate Extraction of Noise Source Impedance of a SMPS under
... of the inserted components must be much larger or smaller than the noise source impedances [14] [15]. Hence, the accuracy deteriorates if these conditions are not met. Moreover, it only provides the magnitude information of the noise source impedance and the phase information can only be estimated w ...
... of the inserted components must be much larger or smaller than the noise source impedances [14] [15]. Hence, the accuracy deteriorates if these conditions are not met. Moreover, it only provides the magnitude information of the noise source impedance and the phase information can only be estimated w ...
