EL2075C
... so that this ‘‘extra’’ bandwidth in low-gain applications does not come at the expense of stability. As seen in the typical performance curves, the EL2075 in a gain of a 10 only exhibits 1.5 dB of peaking with a 100X load. ...
... so that this ‘‘extra’’ bandwidth in low-gain applications does not come at the expense of stability. As seen in the typical performance curves, the EL2075 in a gain of a 10 only exhibits 1.5 dB of peaking with a 100X load. ...
Connect
... 1) The creation of current IA through loop A produces a a magnetic field in the volume surrounding loop A. The energy stored in this field is proportional to IA . 2) The area of loop B intersects magnetic flux from the magnetic field surrounding loop A. The quantity of ...
... 1) The creation of current IA through loop A produces a a magnetic field in the volume surrounding loop A. The energy stored in this field is proportional to IA . 2) The area of loop B intersects magnetic flux from the magnetic field surrounding loop A. The quantity of ...
Feb 2001 New UltraFast Comparators: Rail-to-Rail Inputs and 2.4V Operation Allow Use on Low Supplies
... The new LT1711 family of UltraFast comparators has fully differential railto-rail inputs and outputs and operates on supplies as low as 2.4V, allowing unfettered application on low voltages. The LT1711 (single) and LT1712 (dual) are specified at 4.5ns of propagation delay and 100MHz toggle frequency ...
... The new LT1711 family of UltraFast comparators has fully differential railto-rail inputs and outputs and operates on supplies as low as 2.4V, allowing unfettered application on low voltages. The LT1711 (single) and LT1712 (dual) are specified at 4.5ns of propagation delay and 100MHz toggle frequency ...
TDA2050 - Hobbielektronika.hu
... - Set the voltage supply at the maximum operating value; - Apply a input signal in the form of a 1KHz tone burst of 1 sec duration: the repetition period of the signal pulses is 60 sec; - The output voltage is measured 1 sec from the start of the pulse; - Increase the input voltage until the output ...
... - Set the voltage supply at the maximum operating value; - Apply a input signal in the form of a 1KHz tone burst of 1 sec duration: the repetition period of the signal pulses is 60 sec; - The output voltage is measured 1 sec from the start of the pulse; - Increase the input voltage until the output ...
Analog Devices Welcomes Hittite Microwave Corporation
... noise phase-locked loop applications for inputs from 10 to 1300 MHz. Its combination of high frequency of operation along with its ultra low phase noise floor make possible synthesizers with wide loop bandwidth and low N resulting in fast switching and very low phase noise. When used in conjunction ...
... noise phase-locked loop applications for inputs from 10 to 1300 MHz. Its combination of high frequency of operation along with its ultra low phase noise floor make possible synthesizers with wide loop bandwidth and low N resulting in fast switching and very low phase noise. When used in conjunction ...
MATHEMATICAL MODELLING OF THE LC-LADDER AND CAPACITIVE SHUNT-SHUNT FEEDBACK LNA TOPOLOGY
... area of research for many years. While LNA design techniques in narrowband applications have been researched for some time, wideband techniques have received more thorough investigation in the last few years as well; especially since the approval of the application of ultra-wideband (UWB) technology ...
... area of research for many years. While LNA design techniques in narrowband applications have been researched for some time, wideband techniques have received more thorough investigation in the last few years as well; especially since the approval of the application of ultra-wideband (UWB) technology ...
ENEE417 Final Lab Report: Power Amplifier Design
... audio power amplifier. A power amplifier circuit is used to increase the performance of the sound source, thus making it louder. In general, the purpose of an amplifier is to take an input signal and make it stronger or increase its amplitude. So a fairly high-quality audio amplifier takes in a smal ...
... audio power amplifier. A power amplifier circuit is used to increase the performance of the sound source, thus making it louder. In general, the purpose of an amplifier is to take an input signal and make it stronger or increase its amplitude. So a fairly high-quality audio amplifier takes in a smal ...
OP275 - Analog Devices
... The OP275 is the first amplifier to feature the Butler Amplifier front end. This new front end design combines both bipolar and JFET transistors to attain amplifiers with the accuracy and low noise performance of bipolar transistors, and the speed and sound quality of JFETs. Total Harmonic Distortio ...
... The OP275 is the first amplifier to feature the Butler Amplifier front end. This new front end design combines both bipolar and JFET transistors to attain amplifiers with the accuracy and low noise performance of bipolar transistors, and the speed and sound quality of JFETs. Total Harmonic Distortio ...
Untitled - Standard Audio
... the amount of reverberation applied to the signal. With the control fully counter clockwise no reverb is applied. As you rotate the control clockwise the reverb increases. 9. Lamp: This lamp illuminates when the amplifier is turned on. 10. On/Off Switch: Use this switch to turn the amplifier on and ...
... the amount of reverberation applied to the signal. With the control fully counter clockwise no reverb is applied. As you rotate the control clockwise the reverb increases. 9. Lamp: This lamp illuminates when the amplifier is turned on. 10. On/Off Switch: Use this switch to turn the amplifier on and ...
F. (Francesco) Maddalena
... Q SV (w ) / Zinw Where SV(w) is the spectral density of the voltage noise, Zin the input impedance and w the frequency ...
... Q SV (w ) / Zinw Where SV(w) is the spectral density of the voltage noise, Zin the input impedance and w the frequency ...
Untitled - Carhifi
... more, and is thus more flexible. But that’s the point: the three-channel amp has the not-to-besniffed-at advantage of being designed specifically for one single application – to power a front system and one or more subwoofers. For this reason the subwoofer channel in the A5 is on the one hand also s ...
... more, and is thus more flexible. But that’s the point: the three-channel amp has the not-to-besniffed-at advantage of being designed specifically for one single application – to power a front system and one or more subwoofers. For this reason the subwoofer channel in the A5 is on the one hand also s ...
Valve RF amplifier
A valve RF amplifier (UK and Aus.) or tube amplifier (U.S.), is a device for electrically amplifying the power of an electrical radio frequency signal.Low to medium power valve amplifiers for frequencies below the microwaves were largely replaced by solid state amplifiers during the 1960s and 1970s, initially for receivers and low power stages of transmitters, transmitter output stages switching to transistors somewhat later. Specially constructed valves are still in use for very high power transmitters, although rarely in new designs.