RF5602 3.0V TO 5.0V, 2.3GHz TO 2.7GHz LINEAR POWER AMPLIFIER Features
... power up. If function is not desired, pin may be connected to VREG. First stage input bias voltage. This pin requires a regulated supply to maintain nominal bias current. Second stage input bias voltage. This pin requires a regulated supply to maintain nominal bias current. Third stage input bias vo ...
... power up. If function is not desired, pin may be connected to VREG. First stage input bias voltage. This pin requires a regulated supply to maintain nominal bias current. Second stage input bias voltage. This pin requires a regulated supply to maintain nominal bias current. Third stage input bias vo ...
EMI Suppression with Ferrites
... Design Tradeoffs & Comparisons •For the control of EMI, desire good filter performance at low cost over the WIDE range 10 kHz-40 GHz!! •To get high performance from traditional L-C-L filtering, need many L’s and C’s, but this can lead to ugly high frequency resonances •Adding lossless energy storage ...
... Design Tradeoffs & Comparisons •For the control of EMI, desire good filter performance at low cost over the WIDE range 10 kHz-40 GHz!! •To get high performance from traditional L-C-L filtering, need many L’s and C’s, but this can lead to ugly high frequency resonances •Adding lossless energy storage ...
Line Reactors - Advanced Industry Support, Inc.
... continuously to compensate for capacitor tolerance and aging. It must also be rated to handle fifth harmonic current of a magnitude equal to 15% of the capacitor fundamental current rating. The nameplate must indicate the rated fundamental and harmonic currents and frequencies. Reactors must be copp ...
... continuously to compensate for capacitor tolerance and aging. It must also be rated to handle fifth harmonic current of a magnitude equal to 15% of the capacitor fundamental current rating. The nameplate must indicate the rated fundamental and harmonic currents and frequencies. Reactors must be copp ...
User Manual - Motortronics
... objects. Install on nonflammable objects such as metal surfaces. If several inverters are placed in the same control panel, provide adequate ventilation to keep the temperature below 40°C (104°F) to avoid overheating or fire. When removing or installing the digital operator, turn off the power first ...
... objects. Install on nonflammable objects such as metal surfaces. If several inverters are placed in the same control panel, provide adequate ventilation to keep the temperature below 40°C (104°F) to avoid overheating or fire. When removing or installing the digital operator, turn off the power first ...
MAX512/MAX513 Low-Cost, Triple, 8-Bit Voltage-Output DACs with Serial Interface _______________General Description
... Reference Inputs and DAC Output Range The voltage at REF_ sets the full-scale output of the DACs. The input impedance of the REF_ inputs is code dependent. The lowest value, approximately 12kΩ for REFC (8kΩ for REFAB), occurs when the input code is 01010101 (55hex). The maximum value of infinity occ ...
... Reference Inputs and DAC Output Range The voltage at REF_ sets the full-scale output of the DACs. The input impedance of the REF_ inputs is code dependent. The lowest value, approximately 12kΩ for REFC (8kΩ for REFAB), occurs when the input code is 01010101 (55hex). The maximum value of infinity occ ...
AAT3686 数据资料DataSheet下载
... The adapter charge input constant current level can be programmed up to 1.5A for rapid charging applications. In the absence of a high current adapter input source, the AAT3686 can be powered from a USB port VBUS supply. Depending on the USB port type, the AAT3686 constant charge current can be exte ...
... The adapter charge input constant current level can be programmed up to 1.5A for rapid charging applications. In the absence of a high current adapter input source, the AAT3686 can be powered from a USB port VBUS supply. Depending on the USB port type, the AAT3686 constant charge current can be exte ...
Outline - 正修科技大學
... impedance. Following that, the strip width should be minimized to decrease the overall dimension, as well as to suppress higher-order modes. However, a smaller strip width leads to higher losses. 2) Power-handling capability in microstrip line is relatively low. To increase peak power, the thickness ...
... impedance. Following that, the strip width should be minimized to decrease the overall dimension, as well as to suppress higher-order modes. However, a smaller strip width leads to higher losses. 2) Power-handling capability in microstrip line is relatively low. To increase peak power, the thickness ...
owner`s manual - Systematics, Inc.
... This unit is intended for use in situations where there is a direct pipeline from an unfrozen, high pressure pipeline to an open faucet. It may be used on hot water heating systems. However, the design of these systems presents problems which may make the Icebreaker’s use ineffective. 1. Because the ...
... This unit is intended for use in situations where there is a direct pipeline from an unfrozen, high pressure pipeline to an open faucet. It may be used on hot water heating systems. However, the design of these systems presents problems which may make the Icebreaker’s use ineffective. 1. Because the ...
A DC Motor Controller Using The ZILOG Z86E06 MCU Application
... devices configured in an “H” pattern (see Figure 1). In the center of the “H” is the motor itself. To drive the motor in the forward direction, current flows through Q1 and Q4. To turn the motor in the reverse direction, Q1 and Q4 are turned off, and Q2 and Q3 are energized. External logic is needed ...
... devices configured in an “H” pattern (see Figure 1). In the center of the “H” is the motor itself. To drive the motor in the forward direction, current flows through Q1 and Q4. To turn the motor in the reverse direction, Q1 and Q4 are turned off, and Q2 and Q3 are energized. External logic is needed ...
LTC4060 - Standalone Linear NiMH/NiCd Fast Battery Charger
... which is above the specified maximum operating junction temperature. Continuous operation above the specified maximum operation temperature may result in device degradation or failure. Operating junction temperature TJ (in °C) is calculated from the ambient temperature TA and the average power dissi ...
... which is above the specified maximum operating junction temperature. Continuous operation above the specified maximum operation temperature may result in device degradation or failure. Operating junction temperature TJ (in °C) is calculated from the ambient temperature TA and the average power dissi ...
5 Configuration
... Thyristor control............................................................................................................... Subordinate control loop ................................................................................................. Cycle time ..................................... ...
... Thyristor control............................................................................................................... Subordinate control loop ................................................................................................. Cycle time ..................................... ...
Timer and switching relay
... The time elapse can be interrupted any number of times. Even during the voltage interruption, the immediate contact remains in the operating position. If the preselected time is attained. The latch pin is released and the timed contact is activated. Impulse triggering: To activate the zero voltage-p ...
... The time elapse can be interrupted any number of times. Even during the voltage interruption, the immediate contact remains in the operating position. If the preselected time is attained. The latch pin is released and the timed contact is activated. Impulse triggering: To activate the zero voltage-p ...
Valve RF amplifier
A valve RF amplifier (UK and Aus.) or tube amplifier (U.S.), is a device for electrically amplifying the power of an electrical radio frequency signal.Low to medium power valve amplifiers for frequencies below the microwaves were largely replaced by solid state amplifiers during the 1960s and 1970s, initially for receivers and low power stages of transmitters, transmitter output stages switching to transistors somewhat later. Specially constructed valves are still in use for very high power transmitters, although rarely in new designs.