![OPA2830](http://s1.studyres.com/store/data/008895568_1-1d113282dfacf387b2e77e29384e2962-300x300.png)
Broadband Impedance Matching for Inductive Interconnect in VLSI
... Work done in [7] and [8] showed an implementation of an embedded film capacitor (EFC) using standard copper clad lamination. A standard dielectric material was used (FR-4) with a dielectric constant 4.6. The capacitor’s effectiveness was compared to that of 16 discrete capacitors in the application ...
... Work done in [7] and [8] showed an implementation of an embedded film capacitor (EFC) using standard copper clad lamination. A standard dielectric material was used (FR-4) with a dielectric constant 4.6. The capacitor’s effectiveness was compared to that of 16 discrete capacitors in the application ...
40-Gb/s Transimpedance Amplifier in 0.18
... by a parallel resonance with Cd and CL. If Ls1 is also employed, the bandwidth can be further enhanced by a series resonance with CL at higher frequencies, which forces more current gmvgs to flow through Ls1 and reach the output terminal. Finally, by introducing one more inductor Ld1, the rest of th ...
... by a parallel resonance with Cd and CL. If Ls1 is also employed, the bandwidth can be further enhanced by a series resonance with CL at higher frequencies, which forces more current gmvgs to flow through Ls1 and reach the output terminal. Finally, by introducing one more inductor Ld1, the rest of th ...
AD8106 数据手册DataSheet 下载
... with 1% settling. With −78 dB of crosstalk and −97 dB isolation (@ 5 MHz), the AD8106/AD8107 are useful in many high speed applications. The differential gain and differential phase of greater than 0.02% and 0.02° respectively, along with 0.1 dB flatness out to 60 MHz, make the AD8106/AD8107 ideal f ...
... with 1% settling. With −78 dB of crosstalk and −97 dB isolation (@ 5 MHz), the AD8106/AD8107 are useful in many high speed applications. The differential gain and differential phase of greater than 0.02% and 0.02° respectively, along with 0.1 dB flatness out to 60 MHz, make the AD8106/AD8107 ideal f ...
SP319
... The RS-232 drivers are inverting transmitters, which accept either TTL or CMOS inputs and output the RS-232 signals with an inverted sense relative to the input logic levels. Typically, the RS-232 output voltage swing is +9V with no load, and +5V minimum with full load. The transmitter outputs are p ...
... The RS-232 drivers are inverting transmitters, which accept either TTL or CMOS inputs and output the RS-232 signals with an inverted sense relative to the input logic levels. Typically, the RS-232 output voltage swing is +9V with no load, and +5V minimum with full load. The transmitter outputs are p ...
Zobel network
![](https://en.wikipedia.org/wiki/Special:FilePath/SB_test_room_1959.jpg?width=300)
For the wave filter invented by Zobel and sometimes named after him see m-derived filters.Zobel networks are a type of filter section based on the image-impedance design principle. They are named after Otto Zobel of Bell Labs, who published a much-referenced paper on image filters in 1923. The distinguishing feature of Zobel networks is that the input impedance is fixed in the design independently of the transfer function. This characteristic is achieved at the expense of a much higher component count compared to other types of filter sections. The impedance would normally be specified to be constant and purely resistive. For this reason, they are also known as constant resistance networks. However, any impedance achievable with discrete components is possible.Zobel networks were formerly widely used in telecommunications to flatten and widen the frequency response of copper land lines, producing a higher-quality line from one originally intended for ordinary telephone use. However, as analogue technology has given way to digital, they are now little used.When used to cancel out the reactive portion of loudspeaker impedance, the design is sometimes called a Boucherot cell. In this case, only half the network is implemented as fixed components, the other half being the real and imaginary components of the loudspeaker impedance. This network is more akin to the power factor correction circuits used in electrical power distribution, hence the association with Boucherot's name.A common circuit form of Zobel networks is in the form of a bridged T. This term is often used to mean a Zobel network, sometimes incorrectly when the circuit implementation is, in fact, something other than a bridged T.Parts of this article or section rely on the reader's knowledge of the complex impedance representation of capacitors and inductors and on knowledge of the frequency domain representation of signals.↑