![File](http://s1.studyres.com/store/data/001112581_1-f362cb3ff56aafefd70ff569f9ffd00e-300x300.png)
(CPUfreq/freq)/2) * CPUclockTicTime Why?
... • Call OutputCaptureEX(pin, intervals, count, flags, repeatCount) ...
... • Call OutputCaptureEX(pin, intervals, count, flags, repeatCount) ...
I/O - Renesas e
... The clock is turned off in Single-chip mode and also when it isn’t required for clock synchronization in Extended mode Can be implemented using a switch at the output driver Performs best when the clock control is configured at the source ...
... The clock is turned off in Single-chip mode and also when it isn’t required for clock synchronization in Extended mode Can be implemented using a switch at the output driver Performs best when the clock control is configured at the source ...
ICL7135 Datasheet
... microprocessors. There are 5 negative going STROBE pulses that occur in the center of each of the digit drive pulses and occur once and only once for each measurement cycle starting 101 clock pulses after the end of the full measurement cycle. Digit 5 (MSD) goes high at the end of the measurement cy ...
... microprocessors. There are 5 negative going STROBE pulses that occur in the center of each of the digit drive pulses and occur once and only once for each measurement cycle starting 101 clock pulses after the end of the full measurement cycle. Digit 5 (MSD) goes high at the end of the measurement cy ...
Analog-Digital Conversion
... use a capacitor connected to a reference voltage. the capacitor voltage starts at zero and is charged for a set time by the output voltage of a sample-and-hold circuit. the capacitor is then switched to a known negative voltage reference, and charged in the opposite direction until it reaches zero v ...
... use a capacitor connected to a reference voltage. the capacitor voltage starts at zero and is charged for a set time by the output voltage of a sample-and-hold circuit. the capacitor is then switched to a known negative voltage reference, and charged in the opposite direction until it reaches zero v ...
Physics 4700 Experiment 2 R-L-C Circuits
... both connected to ground. If the two black terminals are connected to two different points in the circuit, both points will be at the same potential, i.e. ground. Therefore make sure that the scope ground and the signal generator ground are connected to the same point in the circuit for any measurem ...
... both connected to ground. If the two black terminals are connected to two different points in the circuit, both points will be at the same potential, i.e. ground. Therefore make sure that the scope ground and the signal generator ground are connected to the same point in the circuit for any measurem ...
555 Timers (word)
... This 555 is set up in an astable mode. The 555 is triggered on its own. To figure out the values for Ra, Rb, and C you can use the chart on the right or the following equations: The charge time (output high) is given by: t1 = 0.693 (RA +RB )C And the discharge time (output low) by: t2 = 0.693 (RB )C ...
... This 555 is set up in an astable mode. The 555 is triggered on its own. To figure out the values for Ra, Rb, and C you can use the chart on the right or the following equations: The charge time (output high) is given by: t1 = 0.693 (RA +RB )C And the discharge time (output low) by: t2 = 0.693 (RB )C ...
(ADC) and Digital to analog converter (DAC)
... What input is needed to get a 6.5 volt output? 2. A bipolar DAC hat 10 bits and a reference of 5v.what outputs will result from input of 04FH and 2A4H.What digital input gives a zero output voltage? 3. Determine how many bits a D/A converter must have to provide output increments of 0.04 volts or le ...
... What input is needed to get a 6.5 volt output? 2. A bipolar DAC hat 10 bits and a reference of 5v.what outputs will result from input of 04FH and 2A4H.What digital input gives a zero output voltage? 3. Determine how many bits a D/A converter must have to provide output increments of 0.04 volts or le ...
Time-to-digital converter
![](https://commons.wikimedia.org/wiki/Special:FilePath/CMOS_TW_OSC_000.png?width=300)
In electronic instrumentation and signal processing, a time to digital converter (abbreviated TDC) is a device for recognizing events and providing a digital representation of the time they occurred. For example, a TDC might output the time of arrival for each incoming pulse. Some applications wish to measure the time interval between two events rather than some notion of an absolute time.In electronics time-to-digital converters (TDCs) or time digitizers are devices commonly used to measure a time interval and convert it into digital (binary) output. In some cases interpolating TDCs are also called time counters (TCs).TDCs are used in many different applications, where the time interval between two signal pulses (start and stop pulse) should be determined. Measurement is started and stopped, when either the rising or the falling edge of a signal pulse crosses a set threshold. These requirements are fulfilled in many physical experiments, like time-of-flight and lifetime measurements in atomic and high energy physics, experiments that involve laser ranging and electronic research involving the testing of integrated circuits and high-speed data transfer.