MAX7057EVKIT.pdf
... Does not connect the on-board CS to the IC. When using external SPIK, remove this jumper and apply the CS signal to TP21. Connects the on-board SDI to the IC. SDI can be monitored on TP22. Does not connect the on-board SDI to the IC. When using external SPI, remove this jumper and apply the SDI sign ...
... Does not connect the on-board CS to the IC. When using external SPIK, remove this jumper and apply the CS signal to TP21. Connects the on-board SDI to the IC. SDI can be monitored on TP22. Does not connect the on-board SDI to the IC. When using external SPI, remove this jumper and apply the SDI sign ...
LT5519 - 0.7GHz to 1.4GHz High Linearity Upconverting Mixer.
... The IF inputs are connected to the emitters of the doublebalanced mixer transistors, as shown in Figure 3. These pins are internally biased and an external resistor must be connected from each IF pin to ground to set the current through the mixer core. The circuit has been optimized to work with 100 ...
... The IF inputs are connected to the emitters of the doublebalanced mixer transistors, as shown in Figure 3. These pins are internally biased and an external resistor must be connected from each IF pin to ground to set the current through the mixer core. The circuit has been optimized to work with 100 ...
Detection of selected EMI Sources in the Prototype of LED Street Light
... connection to the low voltage electricity supply or for battery operation. EN 55015 is a product family standard (largely based on CISPR 15) [20], [23], [24], [25]. Key EMC standards include EN 61000-3-2 for limits on harmonic current emissions, EN 610003-3 for limits on voltage changes, voltage flu ...
... connection to the low voltage electricity supply or for battery operation. EN 55015 is a product family standard (largely based on CISPR 15) [20], [23], [24], [25]. Key EMC standards include EN 61000-3-2 for limits on harmonic current emissions, EN 610003-3 for limits on voltage changes, voltage flu ...
ICS252 - Integrated Device Technology
... an easy to understand, bar code rating for the target output frequencies. The user may evaluate output accuracy, performance trade-off scenarios in seconds. ...
... an easy to understand, bar code rating for the target output frequencies. The user may evaluate output accuracy, performance trade-off scenarios in seconds. ...
International Electrical Engineering Journal (IEEJ) Vol. 6 (2015) No.X, pp. XX-XX
... It has been seen that many researchers proposed various IM models with different power electronics devices based inverters and control the speed of the IM. But harmonics always creates problems in the currents, voltage and developed electromagnetic torque. Therefore, the modeling of such motors is s ...
... It has been seen that many researchers proposed various IM models with different power electronics devices based inverters and control the speed of the IM. But harmonics always creates problems in the currents, voltage and developed electromagnetic torque. Therefore, the modeling of such motors is s ...
G3540
... toward wind power generation. Conventionally, gridconnected cage rotor induction machines are used as wind generators at medium power level. When connected to the constant frequency network, the induction generator runs near synchronous speed drawing the magnetizing current from the mains, thereby r ...
... toward wind power generation. Conventionally, gridconnected cage rotor induction machines are used as wind generators at medium power level. When connected to the constant frequency network, the induction generator runs near synchronous speed drawing the magnetizing current from the mains, thereby r ...
A Soft-Switching Isolated Bidirectional Converter Fed
... an AC electric motor in which the electric current in the rotor needed to produce torque is obtained by electromagnetic induction from the magnetic field of the stator winding. An induction motor can therefore be made without electrical connections to the rotor as are found in universal, DC and sync ...
... an AC electric motor in which the electric current in the rotor needed to produce torque is obtained by electromagnetic induction from the magnetic field of the stator winding. An induction motor can therefore be made without electrical connections to the rotor as are found in universal, DC and sync ...
MAX2031EVKIT.pdf
... This section provides a step-by-step guide to testing the basic functionality of the EV kit. As a general precaution to prevent damaging the outputs by driving high-VSWR loads, do not turn on DC power or RF signal generators until all connections are made. This procedure is specific to operation in ...
... This section provides a step-by-step guide to testing the basic functionality of the EV kit. As a general precaution to prevent damaging the outputs by driving high-VSWR loads, do not turn on DC power or RF signal generators until all connections are made. This procedure is specific to operation in ...
Practical Feedback Loop Design Considerations for
... desired value and then influencing the value of the system variable using the error signal. Switched-mode power supply systems inevitably require feedback control to regulate the output voltage and/or current to a desired value. Fig. 1 shows a simplified feedback circuit for a boost converter. The o ...
... desired value and then influencing the value of the system variable using the error signal. Switched-mode power supply systems inevitably require feedback control to regulate the output voltage and/or current to a desired value. Fig. 1 shows a simplified feedback circuit for a boost converter. The o ...
PDF
... The types of renewable energy include solar, wind, hydrogen, biomass, geothermal, hydropower, and biodiesel. The photovoltaic-based generation has gained importance in DG systems due to its clean, affordable, and available technology. However, there are also challenges associated with the DG, among ...
... The types of renewable energy include solar, wind, hydrogen, biomass, geothermal, hydropower, and biodiesel. The photovoltaic-based generation has gained importance in DG systems due to its clean, affordable, and available technology. However, there are also challenges associated with the DG, among ...
AD8044
... The capacitive load drive of the AD8044 can be increased by adding a low valued resistor in series with the load. Figure 35 shows the effects of a series resistor on capacitive drive for varying voltage gains. As the closed-loop gain is increased, the larger phase margin allows for larger capacitive ...
... The capacitive load drive of the AD8044 can be increased by adding a low valued resistor in series with the load. Figure 35 shows the effects of a series resistor on capacitive drive for varying voltage gains. As the closed-loop gain is increased, the larger phase margin allows for larger capacitive ...
Utility frequency
The utility frequency, (power) line frequency (American English) or mains frequency (British English) is the frequency of the oscillations of alternating current (AC) in an electric power grid transmitted from a power plant to the end-user. In large parts of the world this is 50 Hz, although in the Americas and parts of Asia it is typically 60 Hz. Current usage by country or region is given in the list of mains power around the world.During the development of commercial electric power systems in the late 19th and early 20th centuries, many different frequencies (and voltages) had been used. Large investment in equipment at one frequency made standardization a slow process. However, as of the turn of the 21st century, places that now use the 50 Hz frequency tend to use 220–240 V, and those that now use 60 Hz tend to use 100–127 V. Both frequencies coexist today (Japan uses both) with no great technical reason to prefer one over the other and no apparent desire for complete worldwide standardization.Unless specified by the manufacturer to operate on both 50 and 60 Hz, appliances may not operate efficiently or even safely if used on anything other than the intended frequency.