
The Dipole
... section of transmission line, shows that there will be no radiation along the axis of the structure. This is because the tips of the dipole represent an open circuit. Picturing the dipole folded back to be part of the feed line will make this idea clearer. The current and voltage distribution along ...
... section of transmission line, shows that there will be no radiation along the axis of the structure. This is because the tips of the dipole represent an open circuit. Picturing the dipole folded back to be part of the feed line will make this idea clearer. The current and voltage distribution along ...
LTC5549 - Linear Technology
... may cause permanent damage to the device. Exposure to any Absolute Maximum Rating condition for extended periods may affect device reliability and lifetime. Note 2: The LTC5549 is guaranteed functional over the –40°C to 105°C case temperature range (θJC = 25°C/W). ...
... may cause permanent damage to the device. Exposure to any Absolute Maximum Rating condition for extended periods may affect device reliability and lifetime. Note 2: The LTC5549 is guaranteed functional over the –40°C to 105°C case temperature range (θJC = 25°C/W). ...
LTC2404/LTC2408 - 4-/8-Channel 24
... LTC2404. CH6 (Pin 15): Analog Multiplexer Input. No connect on the LTC2404. CH7 (Pin 17): Analog Multiplexer Input. No connect on the LTC2404. CLK (Pin 19): Shift Clock for Data In. This clock synchronizes the serial data transfer into the MUX. For normal operation, drive this pin in parallel with S ...
... LTC2404. CH6 (Pin 15): Analog Multiplexer Input. No connect on the LTC2404. CH7 (Pin 17): Analog Multiplexer Input. No connect on the LTC2404. CLK (Pin 19): Shift Clock for Data In. This clock synchronizes the serial data transfer into the MUX. For normal operation, drive this pin in parallel with S ...
Slide 1
... • A small AC voltage (e.g. 10 mV – 1 V) is imposed on the sample over a wide range of frequencies (e.g. 1 MHz – 0.1 Hz), and the complex impedance is measured NorFERM-2008, Gol ...
... • A small AC voltage (e.g. 10 mV – 1 V) is imposed on the sample over a wide range of frequencies (e.g. 1 MHz – 0.1 Hz), and the complex impedance is measured NorFERM-2008, Gol ...
ABSTRACT Title of Document: LOW
... capacitive matching is used at the amplifier input. The experimental results of the signal processing chain employing capacitive matching and correlated double sampling show more than 60 times improvement in the signal-to-noise ratio over the same circuit without these improvements. In this dissert ...
... capacitive matching is used at the amplifier input. The experimental results of the signal processing chain employing capacitive matching and correlated double sampling show more than 60 times improvement in the signal-to-noise ratio over the same circuit without these improvements. In this dissert ...
AVTRON ACCel500 FREQUENCY CONVERTERS Frames 4-12
... converter. There is a certain procedure according to which the tests shall be performed. Ignoring this procedure may result in damaged product. • The frequency converter has a large capacitive leakage current. • If the frequency converter is used as a part of a machine, the machine manufacturer is r ...
... converter. There is a certain procedure according to which the tests shall be performed. Ignoring this procedure may result in damaged product. • The frequency converter has a large capacitive leakage current. • If the frequency converter is used as a part of a machine, the machine manufacturer is r ...
TDA8596 1. General description I
... To prevent the amplifier from producing switch-on and switch-off pop noise, the capacitor on the SVR pin is used for smooth start-up and shut-down sequences. Larger capacitors will lead to longer (smoother) start-up and shut-down sequences. Initially the amplifier outputs are charged to Half Supply ...
... To prevent the amplifier from producing switch-on and switch-off pop noise, the capacitor on the SVR pin is used for smooth start-up and shut-down sequences. Larger capacitors will lead to longer (smoother) start-up and shut-down sequences. Initially the amplifier outputs are charged to Half Supply ...
Noise Specs Confusing?
... When esig2 l kRgen, as is the case where signal level is proportional to Rgen (esig e kRgen), it makes sense to use the highest practical value of Rgen. When esig2 k kRgen, it makes sense to use a value of Rgen k ROPT. These conclusions are verified in the Appendix. This all means that it does not m ...
... When esig2 l kRgen, as is the case where signal level is proportional to Rgen (esig e kRgen), it makes sense to use the highest practical value of Rgen. When esig2 k kRgen, it makes sense to use a value of Rgen k ROPT. These conclusions are verified in the Appendix. This all means that it does not m ...
CHAPTER 31 Alternating-Current Circuits
... 40 ∙∙ The circuit shown in Figure 31-33 is called an RC high-pass filter because high input frequencies are transmitted with greater amplitude than low input frequencies. (a) If the input voltage is Vin = V0 cos ωt, show that the output voltage is V0 Vout = (1 / ωRC )2 + 1 (b) At what angular freque ...
... 40 ∙∙ The circuit shown in Figure 31-33 is called an RC high-pass filter because high input frequencies are transmitted with greater amplitude than low input frequencies. (a) If the input voltage is Vin = V0 cos ωt, show that the output voltage is V0 Vout = (1 / ωRC )2 + 1 (b) At what angular freque ...
A Designer`s Guide to Instrumentation Amplifiers, 3rd Edition
... Charles Kitchin and Lew Counts ...
... Charles Kitchin and Lew Counts ...