Download MICROSCOPE REVIEW

MICROSCOPE REVIEW
A. MICROSCOPE PARTS AND THEIR FUNCTION
Throughout this course you will be using a microscope to study both the external and internal structures of a
variety of organisms. The light microscope will enable you to observe structures up to one thousand times
smaller than those visible to the naked eye.
A labeled illustration of the parts of your microscope is included on the following page (figure 1-A). The
important parts of your microscope are:
OCULAR
the lens system closest to the eye that magnifies the image ten
times - 10X
OBJECTIVE
the lens attached to the circular nosepiece that performs the initial
magnification. There are three objectives on the nosepiece:
scanning lens - 4X
low power lens - 10X
high power lens - 40X
Some microscopes have a fourth lens that magnifies 100X and is
used with oil. This lens requires careful cleaning after each use to
remove the oil. USE ONLY LENS CLEANER AND LENS
PAPER TO CLEAN THE LENSES.
COARSE FOCUS KNOB
allows vertical movement of the stage so the specimen can be
positioned under the objective to produce an image.
FINE FOCUS KNOB
brings the image into sharper focus.
STAGE
a platform with an opening that permits the beam of light to pass
through the specimen on a glass slide.
DIAPHRAGM
a disk with a variable opening that regulates the diameter of the
light beam from the lamp below.
CONDENSER
a combination of lenses that focus light from the lamp onto the
specimen.
viii
FIGURE 1-A. PARTS OF THE MICROSCOPE
B. TOTAL MAGNIFICATION
To calculate total magnification of a specimen being viewed, multiply the ocular lens magnification (10X)
by the objective lens magnification (4X, 10X, 40X, or 100X).
Total Magnification = (Ocular lens magnification) x (Objective lens magnification)
Example: Total Magnification = (10X) x (40X) = 400X, a 400-fold magnification
ix
C. CARE AND USE OF THE MICROSCOPE
The microscope is a very expensive instrument with very delicate adjustments. It must be handled with
care and respect at all times. Always follow the precautions listed below:
i.
Only lens paper should be used to clean the lenses. Other papers, including KimWipes, will
scratch the lenses.
ii.
When moving the microscope from one place to another, always hold it upright and carry
using two hands, using one hand to support the bottom of the microscope.
iii.
First locate the object to be studied under scanning power and focus with the coarse and fine
focus knobs. Center the object within the field and then turn to higher magnifications if
desired. Use only the fine focus on higher powers.
iv.
Never use the coarse focus knob under higher powers—only under scanning power.
v.
Never focus downward. This means that you should move the stage away (down) from the
objective rather than toward (up) to the objective. If you were to focus upward, it is possible
for you to break the objective or its lenses.
vi.
If your microscope is not working properly, notify your instructor. Do not attempt to fix it
yourself.
vii.
When not using your microscope, turn of its light.
viii.
Remove slides (put them away) and set the scanning objective in place before putting the
microscope away. Make sure the stage is clean and the lenses are dry. If an oil immersion
objective was used, be sure to clean it with lens cleaner and lens paper before storing the
microscope.
ix.
Do not transfer oculars or objectives from one microscope to another.
To use the microscope:
1.
Rotate the nosepiece until the scanning objective clicks into position. Make sure there is
sufficient light passing through the diaphragm opening in the stage. However, too much light
will wash out the image altogether.
2.
Place the slide on the stage. Center the slide so that the light passes through the spot where
you think the specimen is located.
3.
Use the coarse focus to bring the stage as close to the objective as the knob allows. Then,
looking through the ocular, use the coarse focus to move the stage away from the objective.
An image should come into focus.
4.
Use the fine focus to produce a sharper image. After centering the specimen in the field of
view, switch to the 10X objective. Only the fine focus should now be used to obtain a sharp
image. If higher magnification is needed, again make sure the specimen is centered in the field
of view before changing objectives.
x