Survey
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
LCD Liquid crystal instrument User Manual Open headlight / cruise Parameters plus one Parameters minus one Turn on/off the power 1.Battery Capacity indicator 2.Speed 3.Output power indicator 4.Speed / PAS indicator 5.Interface icon indicator parameter settings Speed indicator 2. Speed display Battery power Voltage Cruise indicator The magnetic pole conversion ratio 3. Output power indication Motor power wheel diameter KM/H 1.Black Ground line throttle fault 2.Green Signal T 4.Speed / PAS gear indicator Controller fault 3.Blue Signal R 4.Yellow Key Switch 5.Interface icon indicates Motor fault 5.Red Power time Wheel RPM Single mileage headlight PAS Brake fault Accumulated mileage 1.white Lamp Positive 2.Yellow Lamp negative Introduction LCD instrument function is to divide the speed and PAS to the five lever which bike under the throttle governor. Five-speed lever from low to high respectively 20%, 40%, 60% 80,100%. Under each lever 1: 1 PAS and throttle generated different speed. LCD control the power to supply for the bike. When turning off the LCD, the whole bike power cut off. No action from throttle and PAS within five minutes, the LCD will turn to sleep state to save the battery. Basic parameter settings Press the up and down key to enter the settings interface . P0 set the point of Battery voltage protection,used to adjust the accuracy of the power display: 24V battery set to 20V, 36V battery set to 31V, 48V battery set to 42V, et to 26,Scooter motor is 8 inch,set to 8. P2 setting the Pole proportion. Reference for motor magnetic pole and deceleration ratio setting, conventional 26inch gear motor set to 45. 8inch gear less motor set to 15,Adjusted up and down according to the motor rated speed. P3 set the speed detection. Inner speed sensor motor with 1 signal set 1, outer speed sensor or Other battery adjust up and down depending on the number of battery series and materials. P1 settings wheel diameter in inches.Such as:bicycle rim is 26 inch,sgear less motor set 0. P4 set the speed unit. The conventional system set to KM/H. Press to change from KM/H or MPH. Function interface introduction Battery indicator Speed indicator Output power PAS level change Accumulated mileage Single mileage Riding time Motor RPM Voltage indicator Fault indicator Headlights indicator PAS instructions Battery indicator Icon located in the upper left corner of the LCD screen. 5 levers means full power.The levers will reduce by the power use. It flash when power shortage. Speed indicator Icon located in the upper right corner of the LCD screen. The default system in miles. when it is full of the conventional electric motors,the rated speed is approximately 28km/h. Output power Icon located in the middle left of the LCD screen. 7 levers means full power output status.Changed according with traffic, load situation . The lower lever means the less output power. PAS Level Icon located in the bottom left corner of the LCD screen. Press key in same time can adjust the gears.The start Level is “1”, the higher level, the faster of the speed. Accumulated mileage Icon located in the bottom right corner of the LCD screen. It shows as ODO. Press the power button in short time can shift and check the interface. Reset: In the interface, press in a little long time, after 5 seconds, the accumulated mileage will be cleared to zero. Single mileage Icon located in the bottom right corner of the LCD screen. It shows as DIS. Press the power button in short time can shift and check the interface. Reset: In the interface, press in a little long time, after 5 seconds,the Single mileage will be cleared to zero. Riding time Icon located in the bottom right corner of the LCD screen. It shows as TIME. Press power button in short time can shift and check the interface. Motor RPM Icon located in the bottom right corner of the LCD screen. It shows as RPM. Press the power button in short time can shift and check the interface. Voltage indicator (The specific numerical of the battery voltage) Icon located in the bottom right corner of the LCD screen. It shows as VOL.Press the power button in short time can shift and check the interface. Fault indicator Icon located in the bottom right corner of the LCD screen. Brake fault icon is is .Throttle fault icon is .Motor fault icon is .Controller fault icon . (When it show fault indicator, please attend if the brake or throttle been reset.) Headlights indicator(normal item don’t have this function,can be customized if needed) Icon located in the bottom right corner of the LCD screen . Press the function in short time can control the headlight on/off. Icon show means headlight on, Icon disappear means headlight off. Cruise indicator Icon located in the bottom right of the LCD screen.The icon is Press the function . in a little long time can enter/exit the cruise state. Icon appear means cruise state, Icon disappear means exit the cruise state.