Download Atmel ATtiny45 Appendix A - ATtiny45 Automotive specification at 150°C Description PRELIMINARY DATASHEET

Atmel ATtiny45
Appendix A - ATtiny45 Automotive specification at 150°C
PRELIMINARY DATASHEET
Description
This document contains information specific to devices operating at temperatures up to
150°C. Only deviations are covered in this appendix, all other information can be found in
the complete Automotive datasheet. The complete Automotive datasheet can be found on
www.atmel.com
7696C–AVR–10/12
1.
Electrical Characteristics
1.1
Absolute Maximum Ratings(1)
Note:
Operating temperature ............. ...... –55°C to +150°C
1.
Storage temperature................. ...... –65°C to +175°C
Voltage on any pin except RESET
with respect to Ground.............. ...... –0.5V to VCC+0.5V
Voltage on RESET with respect to Ground–0.5V to +13.0V
Maximum operating voltage...... ...... 6.0V
Stresses beyond those listed under “Absolute
Maximum Ratings” may cause permanent damage to the device. This is a stress rating only and
functional operation of the device at these or other
conditions beyond those indicated in the operational sections of this specification is not implied.
Exposure to absolute maximum rating conditions
for extended periods may affect device reliability.
DC Current per I/O pin.............. ...... 30.0mA
DC Current VCC and GND pins. ...... 200.0mA
1.2
DC Characteristics
TA = –40°C to 150°C, VCC = 2.7V to 5.5V (unless otherwise noted)(6)
Parameter
Condition
Symbol
Min.
Input Low Voltage, except
XTAL1 and RESET pin
VCC = 2.7V - 5.5V
VIL
Input High Voltage, except
XTAL1 and RESET pins
VCC = 2.7V - 5.5V
Input Low Voltage,
XTAL1 pin
Typ.
Max.
Units
–0.5
0.3VCC(1)
V
VIH
0.6VCC(2)
VCC + 0.5
V
VCC = 2.7V - 5.5V
VIL1
–0.5
0.1VCC(1)
V
Input High Voltage,
XTAL1 pin
VCC = 2.7V - 5.5V
VIH1
0.7VCC(2)
VCC + 0.5
V
Input Low Voltage,
RESET pin
VCC = 2.7V - 5.5V
VIL2
–0.5
0.2VCC(1)
V
Input High Voltage,
RESET pin
VCC = 2.7V - 5.5V
VIH2
0.9VCC(2)
VCC + 0.5
V
Input Low Voltage,
RESET pin as I/O
VCC = 2.7V - 5.5V
VIL3
–0.5
0.3VCC(1)
V
Input High Voltage,
RESET pin as I/O
VCC = 2.7V - 5.5V
VIH3
0.6VCC(2)
VCC + 0.5
V
Output Low Voltage(3),
I/O pin except RESET
IOL = 10mA, VCC = 5V
IOL = 5mA, VCC = 3V
VOL
0.8
0.5
V
Output High Voltage(4),
I/O pin except RESET
IOH = –10mA, VCC = 5V
IOH = –5mA, VCC = 3V
VOH
Input Leakage
Current I/O Pin
VCC = 5.5V, pin low
(absolute value)
IIL
1
µA
Input Leakage
Current I/O Pin
VCC = 5.5V, pin high
(absolute value)
IIH
1
µA
4.0
2.2
V
Reset Pull-up Resistor
RRST
30
60
kΩ
I/O Pin Pull-up Resistor
RPU
20
50
kΩ
Atmel ATtiny45 [Preliminary DATASHEET]
7696C–AVR–10/12
2
1.2
DC Characteristics
TA = –40°C to 150°C, VCC = 2.7V to 5.5V (unless otherwise noted)(6)
Parameter
Condition
Active 4MHz, VCC = 3V
Active 8MHz, VCC = 5V
Active 16MHz, VCC = 5V
Symbol
Min.
Typ.
Max.
Units
ICC
8
16
25
mA
ICC IDLE
6
12
14
mA
90
140
µA
80
120
µA
40
mV
50
nA
Power Supply Current(6)
Idle 4MHz, VCC = 3V
Idle 8MHz, VCC = 5V
Idle 16MHz, VCC = 5V
Power-down mode
WDT enabled, VCC = 3V
WDT enabled, VCC = 5V
WDT disabled, VCC = 3V
WDT disabled, VCC = 5V
ICC PWD
(5)
Analog Comparator
Input Offset Voltage
VCC = 5V
Vin = VCC/2
VACIO
Analog Comparator
Input Leakage Current
VCC = 5V
Vin = VCC/2
IACLK
Analog Comparator
Propagation Delay
VCC = 4.0V
tACPD
<10
-50
500
ns
Atmel ATtiny45 [Preliminary DATASHEET]
7696C–AVR–10/12
3
2.
Memory Endurance
EEPROM endurance: 50,000 Write/Erase cycles
2.1
Maximum Speed vs. VCC
Maximum frequency is dependent on VCC. As shown in Figure 2-1, the maximum frequency vs. VCC curve is linear between
2.7V < VCC 4.5V(6).
Figure 2-1. Maximum Frequency vs. VCC
16 MHz
8 MHz
Safe Operating Area
2.7V
4.5V
5.5V
Atmel ATtiny45 [Preliminary DATASHEET]
7696C–AVR–10/12
4
3.
ADC Characteristics(6)
TA = +125°C to 150°C, VCC = 4.5V to 5.5V (unless otherwise noted)
Parameter
Condition
Symbol
Min
Resolution
Absolute accuracy
(Including INL, DNL,
quantization error, gain and
offset error)
Typ
Max
Units
10
VREF = 4V, VCC = 4V,
ADC clock = 200kHz
VREF = 4V, VCC = 4V,
ADC clock = 200kHz
Bits
2
3.5
LSB
2
3.5
LSB
Noise Reduction Mode
Integral Non-Linearity (INL)
VREF = 4V, VCC = 4V,
ADC clock = 200 kHz
0.6
2.5
LSB
Differential Non-Linearity
(DNL)
VREF = 4V, VCC = 4V,
ADC clock = 200kHz
0.30
1.0
LSB
Gain Error
VREF = 4V, VCC = 4V,
ADC clock = 200kHz
–1.3
3.5
LSB
Offset Error
VREF = 4V, VCC = 4V,
ADC clock = 200kHz
1.8
3.5
LSB
Conversion Time
Free Running Conversion
–3.5
13 cycles
Clock Frequency
µs
50
200
kHz
Analog Supply Voltage
AVCC
VCC – 0.3
VCC + 0.3
V
Reference Voltage
VREF
1.0
AVCC
V
VIN
GND
VREF – 50mV
V
Input Voltage
Input Bandwidth
38.5
kHz
Internal Voltage Reference
VINT
1.0
1.1
1.2
V
Reference Input
Resistance
RREF
25.6
32
38.4
kΩ
Analog Input Resistance
RAIN
Notes:
100
MΩ
1. “Max” means the highest value where the pin is guaranteed to be read as low
2. “Min” means the lowest value where the pin is guaranteed to be read as high
3. Although each I/O port can sink more than the test conditions (20mA at VCC = 5V) under steady state conditions (non-transient), the following must be observed:
1] The sum of all IOL, for all ports, should not exceed 400mA.
2] The sum of all IOL, for ports C0 - C5, should not exceed 200mA.
3] The sum of all IOL, for ports C6, D0 - D4, should not exceed 300mA.
4] The sum of all IOL, for ports B0 - B7, D5 - D7, should not exceed 300mA.
If IOL exceeds the test condition, VOL may exceed the related specification. Pins are not guaranteed to sink current greater
than the listed test condition.
4. Although each I/O port can source more than the test conditions (20mA at Vcc = 5V) under steady state conditions (nontransient), the following must be observed:
1] The sum of all IOH, for all ports, should not exceed 400mA.
2] The sum of all IOH, for ports C0 - C5, should not exceed 200mA.
3] The sum of all IOH, for ports C6, D0 - D4, should not exceed 300mA.
4] The sum of all IOH, for ports B0 - B7, D5 - D7, should not exceed 300mA.
If IOH exceeds the test condition, VOH may exceed the related specification. Pins are not guaranteed to source current
greater than the listed test condition.
5. Minimum VCC for Power-down is 2.5V.
6. For temperature range +125°C to +150°C only. For –40°C to +125°C, refer to ATtiny45 Automotive datasheet. Data for 2.7V
to 4.5V are given for information only. Products are shipped tested at 5.0V ±10% only.
Atmel ATtiny45 [Preliminary DATASHEET]
7696C–AVR–10/12
5
4.
ATtiny45 Typical Characteristics
4.1
Active Supply Current
Figure 4-1. Active Supply Current vs. Frequency (1 - 20 MHz)
ACTIVE S UP P LY CURRENT vs . FREQUENCY
1 - 20MHz, 150˚C
16
14
5.5 V
12
5.0 V
4.5 V
I CC
10
4.0 V
8
3.3 V
6
2.7 V
4
2
0
0
2
4
6
8
10
12
14
16
18
20
Fre que nc y (MHz )
Figure 4-2. Idle Supply Current vs. Frequency (1 - 20 MHz)
IDLE S UP P LY CURRENT vs . FREQUENCY
1 - 20MHz , 150˚C
0.14
0.12
5.5 V
0.1
5.0 V
Idle(mA)
4.5 V
0.08
0.06
3.3 V
2.7 V
0.04
0.02
0
0
2
4
6
8
10
12
14
16
18
20
Fre que nc y (MHz )
Atmel ATtiny45 [Preliminary DATASHEET]
7696C–AVR–10/12
6
Power-Down Supply Current
Figure 4-3. Power-down Supply Current vs. VCC (Watchdog Timer Disabled)
P OWER-DOWN S UP P LY CURRENT vs . VC C
WATCHDOG TIMER DISABLED
14
150 ˚C
12
ICC (uA)
10
8
6
4
125 ˚C
2
-40 ˚C
85 ˚C
25 ˚C
0
2.5
3
3.5
4
4.5
5
5.5
V CC (V)
Figure 4-4. Power-down Supply Current vs. VCC (Watchdog Timer Enabled)
P OWER-DOWN S UP P LY CURRENT vs . VC C
WATCHDOG TIMER ENABLED
20
150 ˚C
18
16
14
ICC (uA)
4.2
12
10
125 ˚C
-40 ˚C
85 ˚C
25
8
6
4
2
0
2.5
3
3.5
4
4.5
5
5.5
V CC (V)
Atmel ATtiny45 [Preliminary DATASHEET]
7696C–AVR–10/12
7
Pin Pull-up
Figure 4-5. I/O Pin Pull-up Resistor Current vs. Input Voltage (VCC = 5V)
I/O P IN P ULL-UP RES IS TOR CURRENT vs . INP UT VOLTAGE
Vc c = 5.0V
160
150 ˚C
140
120 -40 ˚C
IOP (uA)
100
80
60
40
20
0
0
0.5
1
1.5
2
2.5
3
3.5
4
4.5
5
V OP (V)
Figure 4-6. Output Low Voltage vs. Output Low Current (VCC = 5V)
I/O P IN OUTP UT VOLTAGE vs . S INK CURRENT
Vc c = 5.0V
0.7
150
125
0.6
85
0.5
V OL (V)
4.3
25
-40
0.4
0.3
0.2
0.1
0
0
2
4
6
8
10
12
14
16
18
20
IOL (V)
Atmel ATtiny45 [Preliminary DATASHEET]
7696C–AVR–10/12
8
Figure 4-7. Output Low Voltage vs. Output Low Current (VCC = 3V)
I/O P IN OUTP UT VOLTAGE vs . S INK CURRENT
Vc c = 3.0V
1.2
150
125
1
85
V OL (V)
0.8
25
0.6
-40
0.4
0.2
0
0
2
4
6
8
10
12
14
16
18
20
IOL (V)
Figure 4-8. Output High Voltage vs. Output High Current (VCC = 5V)
I/O P IN OUTP UT VOLTAGE vs . S OURCE CURRENT
Vc c = 5.0V
5.1
5
4.9
V OH (V)
4.8
4.7
4.6
-40
4.5
25
85
125
150
4.4
4.3
4.2
0
2
4
6
8
10
12
14
16
18
20
IOH (mA)
Atmel ATtiny45 [Preliminary DATASHEET]
7696C–AVR–10/12
9
Figure 4-9. Output High Voltage vs. Output High Current (VCC = 3V)
I/O P IN OUTP UT VOLTAGE vs . S OURCE CURRENT
Vc c = 3.0V
3.5
3
V OH (V)
2.5
-40
25
85
125
150
2
1.5
1
0.5
0
0
2
4
6
8
10
12
14
16
18
20
IOH (mA)
Figure 4-10. Reset Pull-Up Resistor Current vs. Reset Pin Voltage (VCC = 5V)
RES ET P ULL-UP RES IS TOR CURRENT vs . RES ET P IN VOLTAGE
120
+150˚C
100
-40˚C
I RE S E T (uA)
80
60
40
20
0
0
1
2
3
4
5
6
V RE S E T (V)
Atmel ATtiny45 [Preliminary DATASHEET]
7696C–AVR–10/12
10
Pin Thresholds and Hysteresis
Figure 4-11. I/O Pin Input Threshold vs. VCC (VIH, I/O Pin Read as ‘1’)
I/O P IN INP UT THRES HOLD VOLTAGE vs . V C C
VIH, IO PIN READ AS '1'
3
150 ˚C
-40 ˚C
2.5
Thre s hold
2
1.5
1
0.5
0
1.5
2
2.5
3
3.5
4
4.5
5
5.5
V CC (V)
Figure 4-12. I/O Pin Input Threshold vs. VCC (VIL, I/O Pin Read as ‘0’)
I/O P IN INP UT THRES HOLD VOLTAGE vs . V C C
VIL, IO PIN READ AS '0'
3
150 ˚C
2.5
-40 ˚C
2
Thre s hold
4.4
1.5
1
0.5
0
1.5
2
2.5
3
3.5
4
4.5
5
5.5
V CC (V)
Atmel ATtiny45 [Preliminary DATASHEET]
7696C–AVR–10/12
11
Figure 4-13. Reset Input Threshold Voltage vs. VCC (VIH, Reset Pin Read as ‘1’)
RES ET INP UT THRES HOLD VOLTAGE vs . VC C
VIH, I/O PIN READ AS '1'
2.5
150 ˚C
-40 ˚C
Thre s hold
2
1.5
1
0.5
0
1.5
2
2.5
3
3.5
4
4.5
5
5.5
V CC (V)
Figure 4-14. Reset Input Threshold Voltage vs. VCC (VIL, Reset Pin Read as ‘0’)
RES ET INP UT THRES HOLD VOLTAGE vs . VC C
VIL, I/O PIN READ AS '0'
2.5
150 ˚C
-40 ˚C
Thre s hold
2
1.5
1
0.5
0
1.5
2
2.5
3
3.5
4
4.5
5
5.5
V CC (V)
Atmel ATtiny45 [Preliminary DATASHEET]
7696C–AVR–10/12
12
Internal Oscillator Speed
Figure 4-15. Watchdog Oscillator Frequency vs. VCC
WATCHDOG OS CILLATOR FREQUENCY vs . OP ERATING VOLTAGE
0.17
FRC (MHz )
0.15
0.13
-40 ˚C
0.11
150 ˚C
0.09
0.07
2
2.5
3
3.5
4
4.5
5
5.5
V CC (V)
Figure 4-16. Calibrated 8 MHz RC Oscillator Frequency vs. Temperature
CALIBRATED 8MHz RC OS CILLATOR FREQUENCY vs . TEMP ERATURE
8.5
8.4
5.0 V
3.0 V
8.3
8.2
FRC (MHz )
4.5
8.1
8
7.9
7.8
7.7
7.6
7.5
-40 -30 -20 -10
0
10
20
30
40
50
60
70
80
90
100 110 120 130 140 150
Te mpe ra ture
Atmel ATtiny45 [Preliminary DATASHEET]
7696C–AVR–10/12
13
Figure 4-17. Calibrated 8 MHz RC Oscillator Frequency vs. VCC
CALIBRATED 8MHz RC OS CILLATOR FREQUENCY vs . V C C
8.6
150 ˚C
125 ˚C
85 ˚C
8.4
FRC (MHz )
8.2
25 ˚C
8
7.8
-40 ˚C
7.6
7.4
7.2
7
1.5
2
2.5
3
3.5
4
4.5
5
5.5
V CC (V)
Figure 4-18. Calibrated 8 MHz RC Oscillator Frequency vs. OSCCAL Value
CALIBRATED 8MHz RC OS CILLATOR FREQUENCY vs . OS CCAL VALUE
V CC = 5V
16
14
150 ˚C
-40 ˚C
FRC (MHz )
12
10
8
6
4
2
0
0
16
32
48
64
80
96
112
128
144
160
176
192
208
224
240
OSCCAL (X1)
Atmel ATtiny45 [Preliminary DATASHEET]
7696C–AVR–10/12
14
BOD Thresholds and Analog Comparator Offset
Figure 4-19. BOD Threshold vs. Temperature (BODLEVEL is 4.3V)
BOD THRES HOLDS vs . TEMP ERATURE
BODLEVEL = 4.3V
4.4
4.35
Ris ing
Thre s hold (V)
4.3
Falling
4.25
4.2
4.15
4.1
4.05
4
-50 -40 -30 -20 -10
0
10
20
30
40
50
60
70
80
90 100 110 120 130 140 150
Te mpe ra ture (C)
Figure 4-20. BOD Threshold vs. Temperature (BODLEVEL is 2.7V)
BOD THRES HOLDS vs . TEMP ERATURE
BODLEVEL = 2.7V
2.8
Ris ing
2.75
Thre s hold (V)
4.6
2.7
Falling
2.65
2.6
2.55
2.5
-50 -40 -30 -20 -10
0
10
20
30
40
50
60
70
80
90 100 110 120 130 140 150
Te mpe ra ture (C)
Atmel ATtiny45 [Preliminary DATASHEET]
7696C–AVR–10/12
15
Figure 4-21. Bandgap Voltage vs. VCC
BANDGAP VOLTAGE vs . V C C
Ba ndga p Volta ge (V)
1.3
1.2
150 ˚C
-40 ˚C
1.1
1
0.9
1.5
2
2.5
3
3.5
4
4.5
5
5.5
Vc c (V)
Peripheral Units
Figure 4-22. Analog to Digital Converter GAIN vs. Temperature, Single Ended
Analog to Digital Converter - GAIN
Single Ende d, Vc c = 4V, Vre f = 4V
0
-0.5
-1
LSB
4.7
-1.5
-2
-2.5
-3
-40 -30 -20 -10
0
10
20
30
40
50
60
70
80
90 100 110 120 130 140 150
Te mpe ra ture
Atmel ATtiny45 [Preliminary DATASHEET]
7696C–AVR–10/12
16
Figure 4-23. Analog to Digital Converter GAIN vs. Temperature, Differential Mode
Analog to Digital Converter - GAIN
Diffe re ntia l Inputs , Vc c = 5V, Vre f = 4V
-1
-1.2
-1.4
-1.6
Diff x20
LSB
-1.8
-2
-2.2
-2.4
-2.6
Diff x1
-2.8
-3
-40 -30 -20 -10
0
10
20
30
40
50
60
70
80
90
100 110 120 130 140 150
Te mpe ra ture
Figure 4-24. Analog to Digital Converter OFFSET vs. Temperature, Single Ended
Analog to Digital Converter - OFFS ET
Single Ende d, Vc c = 4V, Vre f = 4V
2.5
2
LSB
1.5
1
0.5
0
-40 -30 -20 -10
0
10
20
30
40
50
60
70
80
90
100 110 120 130 140 150
Te mpe ra ture
Atmel ATtiny45 [Preliminary DATASHEET]
7696C–AVR–10/12
17
Figure 4-25. Analog to Digital Converter OFFSET vs. Temperature, Differential Mode
Analog to Digital Converter - OFFS ET
Diffe re ntia l Inputs , Vc c = 4V, Vre f = 4V
2
1.5
1
LSB
0.5
0
Diff x1
-0.5
-1
-1.5
-2
-2.5
-40 -30 -20 -10
Diff x20
0
10
20
30
40
50
60
70
80
90 100 110 120 130 140 150
Te mpe ra ture
Figure 4-26. Analog to Digital Converter DNL vs. Temperature, Single Ended
Analog to Digital Converter - Differential Non Linearity DNL
Single Ende d, Vc c = 4V, Vre f = 4V
0.57
0.56
0.55
0.54
LSB
0.53
0.52
0.51
0.5
0.49
0.48
0.47
-40 -30 -20 -10
0
10
20
30
40
50
60
70
80
90
100 110 120 130 140 150
Te mpe ra ture
Atmel ATtiny45 [Preliminary DATASHEET]
7696C–AVR–10/12
18
Figure 4-27. Analog to Digital Converter DNL vs. Temperature, Differential Mode
Analog to Digital Converter - Differential Non Linearity DNL
Diffe re ntia l Inputs , Vc c = 4V, Vre f = 4V
1.6
1.4
Diff x20
1.2
LSB
1
0.8
0.6
0.4
Diff x1
0.2
0
-40 -30 -20 -10
0
10
20
30
40
50
60
70
80
90
100 110 120 130 140 150
Te mpe ra ture
Figure 4-28. Analog to Digital Converter INL vs. Temperature, Single Ended
Analog to Digital Converter - Integral Non Linearity INL
Single Ende d, Vc c = 4V, Vre f = 4V
0.72
0.7
LSB
0.68
0.66
0.64
0.62
0.6
0.58
-40 -30 -20 -10
0
10
20
30
40
50
60
70
80
90
100 110 120 130 140 150
Te mpe ra ture
Atmel ATtiny45 [Preliminary DATASHEET]
7696C–AVR–10/12
19
Figure 4-29. Analog to Digital Converter INL vs. Temperature, Differential Mode
Analog to Digital Converter - Integral Non Linearity INL
Diffe re ntia l Inputs , Vc c = 4V, Vre f = 4V
2.5
2
Diff x20
LSB
1.5
Diff x1
1
0.5
0
-40 -30 -20 -10
0
10
20
30
40
50
60
70
80
90
100 110 120 130 140 150
Te mpe ra ture
Atmel ATtiny45 [Preliminary DATASHEET]
7696C–AVR–10/12
20
Grade 0 Qualification
The ATtiny45 has been developed and manufactured according to the most stringent quality assurance requirements of ISOTS-16949 and verified during product qualification as per AEC-Q100 grade 0.
AEC-Q100 qualification relies on temperature accelerated stress testing. High temperature field usage however may result in
less significant stress test acceleration. In order to prevent the risk that ATtiny45 lifetime would not satisfy the application endof-life reliability requirements, Atmel has extended the testing, whenever applicable (High Temperature Operating Life Test,
High Temperature Storage Life, Data Retention, Thermal Cycles), far beyond the AEC-Q100 requirements. Thereby, Atmel
verified the ATtiny45 has a long safe lifetime period after the grade 0 qualification acceptance limits.
The valid domain calculation depends on the activation energy of the potential failure mechanism that is considered. Examples
are given in figure 1. Therefore any temperature mission profile which could exceed the AEC-Q100 equivalence domain shall
be submitted to Atmel for a thorough reliability analysis
Figure 5-1. AEC-Q100 Lifetime Equivalence
AEC-Q100 Lifetime Equivalence
1000000
100000
10000
Hours
5.
1000
100
10
1
0
20
40
60
80
100
120
140
160
Temperature (°C)
HTOL 0,59eV
HTSL 0,45eV
Atmel ATtiny45 [Preliminary DATASHEET]
7696C–AVR–10/12
21
6.
Ordering Information
6.1
ATtiny45
Table 6-1.
ATtiny45
Speed (MHz)
Power Supply
Ordering Code
Package(1)
Operation Range
16(2)
2.7 - 5.5V
ATtiny45-15MT2
PC
Extended
(–40°C to 150°C)
Notes:
Table 6-2.
1.
Pb-free packaging, complies to the European Directive for Restriction of Hazardous Substances (RoHS directive).
Also Halide free and fully Green.
2.
For speed vs. VCC, see Figure 2-1 on page 4 and complete product datasheet.
Package Information
Package Type
PC
20-lead, 4.0x 4.0mm body, lead pitch 0.60mm, Quad Flat No-lead package
Atmel ATtiny45 [Preliminary DATASHEET]
7696C–AVR–10/12
22
Figure 6-1. Package PC
Atmel ATtiny45 [Preliminary DATASHEET]
7696C–AVR–10/12
23
7.
Document Revision History
7.1
7696B to 7696C
1.
7.2
Figure 6-1 “Package PC” on page 23 updated.
7696A to 7696B
1.
Added EEPROm endurance. See Section 2. “Memory Endurance” on page 4.
Atmel ATtiny45 [Preliminary DATASHEET]
7696C–AVR–10/12
24
Atmel Corporation
2325 Orchard Parkway
Atmel Asia Limited
Unit 01-5 & 16, 19F
Atmel Munich GmbH
Business Campus
Atmel Japan G.K.
16F Shin-Osaki Kangyo Building
San Jose, CA 95131
BEA Tower, Millennium City 5
Parkring 4
1-6-4 Osaki
USA
418 Kwun Tong Roa
D-85748 Garching b. Munich
Shinagawa-ku, Tokyo 141-0032
Tel: (+1) (408) 441-0311
Kwun Tong, Kowloon
GERMANY
JAPAN
Fax: (+1) (408) 487-2600
HONG KONG
Tel: (+49) 89-31970-0
Tel: (+81) (3) 6417-0300
www.atmel.com
Tel: (+852) 2245-6100
Fax: (+49) 89-3194621
Fax: (+81) (3) 6417-0370
Fax: (+852) 2722-1369
© 2012 Atmel Corporation. All rights reserved. / Rev.: 7696C–AVR–10/12
Atmel®, Atmel logo and combinations thereof, Enabling Unlimited Possibilities®, and others are registered trademarks or trademarks of Atmel Corporation or its
subsidiaries. Other terms and product names may be trademarks of others.
Disclaimer: The information in this document is provided in connection with Atmel products. No license, express or implied, by estoppel or otherwise, to any intellectual property right is granted by this
document or in connection with the sale of Atmel products. EXCEPT AS SET FORTH IN THE ATMEL TERMS AND CONDITIONS OF SALES LOCATED ON THE ATMEL WEBSITE, ATMEL ASSUMES
NO LIABILITY WHATSOEVER AND DISCLAIMS ANY EXPRESS, IMPLIED OR STATUTORY WARRANTY RELATING TO ITS PRODUCTS INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
WARRANTY OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, OR NON-INFRINGEMENT. IN NO EVENT SHALL ATMEL BE LIABLE FOR ANY DIRECT, INDIRECT,
CONSEQUENTIAL, PUNITIVE, SPECIAL OR INCIDENTAL DAMAGES (INCLUDING, WITHOUT LIMITATION, DAMAGES FOR LOSS AND PROFITS, BUSINESS INTERRUPTION, OR LOSS OF
INFORMATION) ARISING OUT OF THE USE OR INABILITY TO USE THIS DOCUMENT, EVEN IF ATMEL HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. Atmel makes no
representations or warranties with respect to the accuracy or completeness of the contents of this document and reserves the right to make changes to specifications and products descriptions at any time
without notice. Atmel does not make any commitment to update the information contained herein. Unless specifically provided otherwise, Atmel products are not suitable for, and shall not be used in,
automotive applications. Atmel products are not intended, authorized, or warranted for use as components in applications intended to support or sustain life.