Download IF 1720 Revision 2

Survey
yes no Was this document useful for you?
   Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Document related concepts

Stepper motor wikipedia , lookup

History of electric power transmission wikipedia , lookup

Rectifier wikipedia , lookup

Mechanical filter wikipedia , lookup

Electrical engineering wikipedia , lookup

Telecommunications engineering wikipedia , lookup

Power engineering wikipedia , lookup

Immunity-aware programming wikipedia , lookup

Electrical substation wikipedia , lookup

Opto-isolator wikipedia , lookup

Variable-frequency drive wikipedia , lookup

Electrician wikipedia , lookup

Buck converter wikipedia , lookup

Three-phase electric power wikipedia , lookup

Amtrak's 25 Hz traction power system wikipedia , lookup

Portable appliance testing wikipedia , lookup

Surge protector wikipedia , lookup

Printed circuit board wikipedia , lookup

Voltage optimisation wikipedia , lookup

Alternating current wikipedia , lookup

Single-wire earth return wikipedia , lookup

Metadyne wikipedia , lookup

Ground loop (electricity) wikipedia , lookup

Stray voltage wikipedia , lookup

Switched-mode power supply wikipedia , lookup

Surface-mount technology wikipedia , lookup

Home wiring wikipedia , lookup

Ground (electricity) wikipedia , lookup

Mains electricity wikipedia , lookup

National Electrical Code wikipedia , lookup

Electrical wiring wikipedia , lookup

Earthing system wikipedia , lookup

Electrical wiring in the United Kingdom wikipedia , lookup

Transcript
LED Floodlight FMV Series
50L Industrial LED Floodlight
IF 1720
Installation & Maintenance Information
SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE
Application
FMV 50L LED Floodlights construction is designed for use indoors and outdoors in
marine and wet locations, where moisture, dirt, corrosion, vibration and rough usage may
be present.
•
•
•
•
UL1598 Luminaires, UL1598A Marine, UL8750
•
•
•
•
cUL
Class I, Division 2, Groups A,B,C,D
Class II, Division 1, Groups E,F,G
Class III
FMV 50L LED Floodlights are supplied for use with a choice of voltages:
• 100VAC – 277VAC, 50/60Hz and 127VDC – 250VDC
• 277VAC - 480VAC, 50/60Hz
UL844 Hazardous (Classified), CSA C22.2 No. 137
Wet Locations, NEMA 4X
IP66
WARNING
Yoke Bracket
To avoid the risk of fire, explosion, or electric shock, this product should
be installed, inspected, and maintained by a qualified electrician only, in
accordance with all applicable electrical codes.
WARNING
To avoid electric shock:
Be certain electrical power is OFF before and during installation and
maintenance. Floodlights must be supplied by wiring system suitable for Class
I, Division 2 per NEC with an equipment grounding conductor.
To avoid burning hands:
Make sure lens and lamp are cool when performing maintenance.
WARNING
To avoid potentially unsafe operating conditions:
Side Bracket
Make sure the supply voltage is within the floodlight voltage range stated on
the nameplate.
Do not operate in ambient temperatures above those indicated on the
floodlight nameplate.
Back Cover
Use only replacement parts from Crouse-Hinds.
Ensure supply cable and cable gland meet product rating and conform with
building and electrical codes.
Use proper supply wiring as specified on the floodlight nameplate.
All gasket seals must be clean.
Before opening, electrical power to the floodlight must be turned off. Keep
tightly closed when in operation.
Do not position the floodlight beyond the aiming range limits.
Do not exceed the maximum allowable current draw of 12 Amps when daisy
chaining floodlights.
Installation
Figure 1- Fixture Back View
Wiring
Wiring the Floodlight
1.
Open bottom back cover by loosening eight (8) ¼ 20 X .635” stainless steel cover
screws. All components in the fixture are prewired so only line in, neutral, and
ground need to be connected in the fixture to the terminals per the wiring diagrams
using methods that comply with all applicable codes. Use 75°C min and 600 V
min supply cord with outer sheath diameter in accordance with Table 1. Terminate
the equipment grounding conductor (green) first, the common (white) next, and
finally, the line voltage (black) last. Secure all electrical connections. For DC voltage
applications, connect the positive (+) lead to the white wire and the negative (-) lead
to the black wire.
Mounting
Yoke Mount
1.
Select a durable, corrosion resistant mounting surface capable of supporting
the fixture’s 106 lb (48.1 kg) weight and cantilevered mass (as applicable).
2.
Using the floodlight yoke as a template, mark and drill desired location on
mounting surface.
3.
Secure floodlight yoke to mounting surface by applying proper torque to
four corrosion resistant 1/2 inch bolts or lag screws accompanied by lock
washers.
4.
Ensure that the safety chains are securely fastened between the side
brackets and back covers.
IF 1720 • 10/14
Copyright © 2014, Eaton’s Crouse-Hinds Business
Page 1
TOP HOUSING
DRIVER
INPUT
OUTPUT
LINE IN (BLK)
NEUTRAL (WHT)
GROUND (GRN)
LED CIRCUIT BOARD
-
+
V+ (RED)
V- (BLK)
LED CIRCUIT BOARD
DRIVER
INPUT
OUTPUT
LINE IN (BLK)
NEUTRAL (WHT)
GROUND (GRN)
FILTER
+
LED CIRCUIT BOARD
V+ (RED)
+
V- (BLK)
TERMINAL BLOCK
OR LEVER LOCKS
LED CIRCUIT BOARD
-
GROUND TO
HOUSING
0306637
CABLE
+
BOTTOM HOUSING
INPUT
DRIVER
LINE IN (BLK)
NEUTRAL (WHT)
GROUND (GRN)
TERMINAL
BLOCK OR
LEVER LOCKS
LED CIRCUIT BOARD
OUTPUT
V+ (RED)
-
+
V- (BLK)
Figure 5 - Back Cover Installation
LED CIRCUIT BOARD
LINE IN (BLK)
NEUTRAL (WHT)
GROUND (GRN)
+
INPUT
FILTER
DRIVER
LINE IN (BLK)
NEUTRAL (WHT)
GROUND (GRN)
2.
LED CIRCUIT BOARD
OUTPUT
V+ (RED)
-
+
V- (BLK)
GROUND TO
HOUSING
LED CIRCUIT BOARD
-
+
Figure 2 - Wiring Diagram
AIMING RANGE
105°
Ensure gasket joint, back cover and driver housing surfaces are clean and free
of damage or debris. Put back cover in place on driver housing and start all (8)
back cover screws hand-tight. Initially torque back cover screws to 40 In-lbs in
sequence of A-B-C-D-E-F-G-H as shown in Figure 5. Next torque back cover
screws up to 79 In-lbs again in the sequence of A-B-C-D-E-F-G-H. Finally torque
screws through A-B-C-D-E-F-G-H sequence one final time and ensure torque
values are at 79 In-lbs.
3. To make final vertical adjustment, loosen the pivot bolts on the floodlight yoke
to position floodlight at the desired angle (limited to 60 degrees forward and 45
degrees back).
4. Rotate the floodlight housing to the desired position.
5. Tighten the two 1/2”-13 bolts to 45 ft-lbs (61.0 N-m). Tighten the 5/16”-18 bolts
in the adjustment slots to 12 ft-lbs (16.3 N-m).
6. Turn power on.
Maintenance
45°
60°
45° PAST
VERTICAL
60° BEFORE
VERTICAL
•
Perform visual, electrical, and mechanical inspections on a regular basis. The
environment and frequency of use should determine this. However, it is
recommended that checks be made at least once a year. We recommend an
Electrical Preventive Maintenance Program as described in the National Fire
Protection Association Bulletin NFPA 70B: Recommended Practice for Electrical
Equipment Maintenance (www.nfpa.org).
•
The lens should be cleaned periodically to ensure continued lighting performance.
To clean, wipe the lens with a clean damp cloth. If this is not sufficient, use a
mild soap or a liquid cleaner. Do not use an abrasive, strong alkaline, or acid
cleaner. Damage may result.
•
Visually check for undue heating evidenced by discoloration of wires or other
components, damaged parts, or leakage evidenced by water or corrosion in the
interior. Replace all worn, damaged, or malfunctioning components and clean
gasket seals before putting the luminaire back into service.
•
Electrically check to make sure that all connections are clean and tight.
•
Mechanically check that all parts are properly assembled.
Figure 3 - Aiming Range Adjustment
277
10.90
556.3
21.90
235.8
9.28
532.9
20.98
203.7
8.02
254
10.00
13.9
Ø .55
825
32.48
127
5.00
Replacement parts
Crouse-Hinds FMV 50L LED Floodlights are designed to provide years of reliable
lighting performance. However, should the need for replacement parts arise, they are
available through your authorized Crouse-Hinds distributor. Assistance may also be
obtained through your local Crouse-Hinds representative or the Crouse-Hinds Sales
Service Department, P.O. Box 4999, Syracuse, New York 13221, Phone 866-764-5454.
632.6
24.90
Figure 4 - Fixture dimensions (wire guard and visor options shown)
IF 1720 • 10/14
Copyright © 2014, Eaton’s Crouse-Hinds Business
Page 2
Figure 5 - Fixture with Visor Option
Figure 6 - Fixture with Guard Option
Visor Installation Instructions
Guard Installation Instructions
1.
2.
3.
1.
2.
3.
4.
5.
Remove power from floodlight.
Place floodlight face up.
Carefully align visor with two (2) screw holes at the top of the fixture shown in the
image above.
Install screws provided with visor, taking care to not scratch the finish of the
floodlight. Torque to 80 in-lbs (9.0 N-m).
Install floodlight per above instructions.
NOTE: Visor can be installed before or after floodlight has been in operation.
4.
5.
Remove power from floodlight.
Place floodlight face up.
Carefully align guard with four (4) screw holes on each side of the fixture shown
in the image above.
Install screws provided with guard taking care to not scratch the finish of the
floodlight. Torque to 80 in-lbs (9.0 N-m).
Install floodlight per above instructions.
NOTE: Guard can be installed before or after floodlight has been in operation.
Figure 7 - Fixture with Visor and Guard Options
NOTE: Visor and guard can both be used on a floodlight at the same time. Visor and guard are always installed in the field and are not factory installed.
All statements, technical information and recommendations contained herein are based on information and tests we believe to be reliable. The accuracy or
completeness thereof are not guaranteed. In accordance with Crouse-Hinds “Terms and Conditions of Sale,” and since conditions of use are outside our control,
the purchaser should determine the suitability of the product for his intended use and assumes all risk and liability whatsoever in connection therewith.
Eaton’s Crouse-Hinds Business
1201 Wolf Street Syracuse, New York 13208 • U.S.A.
Copyright© 2014
IF 1720
Revision 2
Revised 10/14
Supersedes 09/14