Download Chapter 4 slides

Chapter 4 roadmap
4.1 Introduction and Network Service Models
4.2 Routing Principles
4.3 Hierarchical Routing
4.4 The Internet (IP) Protocol
4.5 Routing in the Internet
4.6 What’s Inside a Router
4.7 IPv6
4.8 Multicast Routing
4.9 Mobility
Network Layer
4-1
Network layer functions
 transport packet from
sending to receiving hosts
 network layer protocols in
every host, router
three important functions:
 path determination: route
taken by packets from source
to dest. Routing algorithms
 forwarding: move packets
from router’s input to
appropriate router output
 call setup: some network
architectures require router
call setup along path before
data flows
application
transport
network
data link
physical
network
data link
physical
network
data link
physical
network
data link
physical
network
data link
physical
network
data link
physical
network
data link
physical
network
data link
physical
network
data link
physical
application
transport
network
data link
physical
Network Layer
4-2
Network service model
Q: What service model
for “channel”
transporting packets
from sender to
receiver?
 guaranteed bandwidth?
 preservation of inter-packet
timing (no jitter)?
 loss-free delivery?
 in-order delivery?
 congestion feedback to
sender?
The most important
abstraction provided
by network layer:
? ?
?
virtual circuit
or
datagram?
Network Layer
4-3
Datagram networks:
the Internet model
 no call setup at network layer
 routers: no state about end-to-end connections
 no network-level concept of “connection”
 packets forwarded using destination host address
 packets between same source-dest pair may take
different paths
application
transport
network
data link 1. Send data
physical
application
transport
network
2. Receive data
data link
physical
Network Layer
4-4
Chapter 4 roadmap
4.1 Introduction and Network Service Models
4.2 Routing Principles


Link state routing
Distance vector routing
4.3 Hierarchical Routing
4.4 The Internet (IP) Protocol
4.5 Routing in the Internet
4.6 What’s Inside a Router
4.7 IPv6
4.8 Multicast Routing
4.9 Mobility
Network Layer
4-5
Routing
Routing protocol
Goal: determine “good” path
(sequence of routers) thru
network from source to dest.
Graph abstraction for
routing algorithms:
 graph nodes are
routers
 graph edges are
physical links

link cost: delay, $ cost,
or congestion level
5
2
A
B
2
1
D
3
C
3
1
5
F
1
E
2
 “good” path:
 typically means minimum
cost path
 other def’s possible
Network Layer
4-6
Chapter 4 roadmap
4.1 Introduction and Network Service Models
4.2 Routing Principles
4.3 Hierarchical Routing
4.4 The Internet (IP) Protocol
 4.4.1 IPv4 addressing
 4.4.2 Moving a datagram from source to destination
 4.4.3 Datagram format
 4.4.4 IP fragmentation
 4.4.5 ICMP: Internet Control Message Protocol
 4.4.6 DHCP: Dynamic Host Configuration Protocol
 4.4.7 NAT: Network Address Translation
4.5 Routing in the Internet
4.6 What’s Inside a Router
4.7 IPv6
4.8 Multicast Routing
4.9 Mobility
Network Layer
4-7
The Internet Network layer
Host, router network layer functions:
Transport layer: TCP, UDP
Network
layer
IP protocol
•addressing conventions
•datagram format
•packet handling conventions
Routing protocols
•path selection
•RIP, OSPF, BGP
forwarding
table
ICMP protocol
•error reporting
•router “signaling”
Link layer
physical layer
Network Layer
4-8
IP Addressing: introduction
 IP address: 32-bit
identifier for host,
router interface
 interface: connection
between host/router
and physical link



router’s typically have
multiple interfaces
host may have multiple
interfaces
IP addresses
associated with each
interface
223.1.1.1
223.1.2.1
223.1.1.2
223.1.1.4
223.1.1.3
223.1.2.9
223.1.3.27
223.1.2.2
223.1.3.2
223.1.3.1
223.1.1.1 = 11011111 00000001 00000001 00000001
223
1
1
Network Layer
1
4-9
IP Addressing
 IP address:
 network part (high
order bits)
 host part (low order
bits)
 What’s a network ?
(from IP address
perspective)
 device interfaces with
same network part of
IP address
 can physically reach
each other without
intervening router
223.1.1.1
223.1.2.1
223.1.1.2
223.1.1.4
223.1.1.3
223.1.2.9
223.1.3.27
223.1.2.2
LAN
223.1.3.1
223.1.3.2
network consisting of 3 IP networks
(for IP addresses starting with 223,
first 24 bits are network address)
Network Layer 4-10
IP Addressing
How to find the
networks?
 Detach each
interface from
router, host
 create “islands of
isolated networks
223.1.1.2
223.1.1.1
223.1.1.4
223.1.1.3
223.1.9.2
223.1.7.0
223.1.9.1
223.1.7.1
223.1.8.1
223.1.8.0
223.1.2.6
Interconnected
system consisting
of six networks
223.1.2.1
223.1.3.27
223.1.2.2
223.1.3.1
223.1.3.2
Network Layer
4-11
IP Addresses
given notion of “network”, let’s re-examine IP addresses:
“class-full” addressing:
class
A
0 network
B
10
C
110
D
1110
1.0.0.0 to
127.255.255.255
host
network
128.0.0.0 to
191.255.255.255
host
network
multicast address
host
192.0.0.0 to
223.255.255.255
224.0.0.0 to
239.255.255.255
32 bits
Network Layer 4-12
IP addressing: CIDR
 Classful addressing:


inefficient use of address space, address space exhaustion
e.g., class B net allocated enough addresses for 65K hosts,
even if only 2K hosts in that network
 CIDR: Classless InterDomain Routing


network portion of address of arbitrary length
address format: a.b.c.d/x, where x is # bits in network
portion of address
network
part
host
part
11001000 00010111 00010000 00000000
200.23.16.0/23
Network Layer 4-13
IP addresses: how to get one?
Q: How does host get IP address?
 hard-coded by system admin in a file
Wintel: control-panel->network->configuration>tcp/ip->properties
 UNIX: /etc/rc.config
 DHCP: Dynamic Host Configuration Protocol:
dynamically get address from as server
 “plug-and-play”
(more shortly)

Network Layer 4-14
Getting a datagram from source to dest.
forwarding table in A
Dest. Net. next router Nhops
223.1.1
223.1.2
223.1.3
IP datagram:
misc source dest
fields IP addr IP addr
data
A
 datagram remains
unchanged, as it travels
source to destination
 addr fields of interest
here
223.1.1.4
223.1.1.4
1
2
2
223.1.1.1
223.1.2.1
B
223.1.1.2
223.1.1.4
223.1.2.9
223.1.2.2
223.1.1.3
223.1.3.1
223.1.3.27
E
223.1.3.2
Network Layer 4-15
Getting a datagram from source to dest.
forwarding table in A
misc
data
fields 223.1.1.1 223.1.1.3
Dest. Net. next router Nhops
223.1.1
223.1.2
223.1.3
Starting at A, send IP
datagram addressed to B:
 look up net. address of B in
forwarding table
 find B is on same net. as A
 link layer will send datagram
directly to B inside link-layer
frame
 B and A are directly
connected
A
223.1.1.4
223.1.1.4
1
2
2
223.1.1.1
223.1.2.1
B
223.1.1.2
223.1.1.4
223.1.2.9
223.1.2.2
223.1.1.3
223.1.3.1
223.1.3.27
E
223.1.3.2
Network Layer 4-16
Getting a datagram from source to dest.
forwarding table in A
misc
data
fields 223.1.1.1 223.1.2.3
Dest. Net. next router Nhops
223.1.1
223.1.2
223.1.3
Starting at A, dest. E:
 look up network address of E





in forwarding table
E on different network
 A, E not directly attached
routing table: next hop
router to E is 223.1.1.4
link layer sends datagram to
router 223.1.1.4 inside linklayer frame
datagram arrives at 223.1.1.4
continued…..
A
223.1.1.4
223.1.1.4
1
2
2
223.1.1.1
223.1.2.1
B
223.1.1.2
223.1.1.4
223.1.2.9
223.1.2.2
223.1.1.3
223.1.3.1
223.1.3.27
E
223.1.3.2
Network Layer 4-17
Getting a datagram from source to dest.
misc
data
fields 223.1.1.1 223.1.2.3
Arriving at 223.1.4,
destined for 223.1.2.2
 look up network address of E
in router’s forwarding table
 E on same network as router’s
interface 223.1.2.9
 router, E directly attached
 link layer sends datagram to
223.1.2.2 inside link-layer
frame via interface 223.1.2.9
 datagram arrives at
223.1.2.2!!! (hooray!)
forwarding table in router
Dest. Net router Nhops interface
223.1.1
223.1.2
223.1.3
A
-
1
1
1
223.1.1.4
223.1.2.9
223.1.3.27
223.1.1.1
223.1.2.1
B
223.1.1.2
223.1.1.4
223.1.2.9
223.1.2.2
223.1.1.3
223.1.3.1
223.1.3.27
E
223.1.3.2
Network Layer 4-18
IP datagram format
IP protocol version
number
header length
(bytes)
“type” of data
max number
remaining hops
(decremented at
each router)
upper layer protocol
to deliver payload to
how much overhead
with TCP?
 20 bytes of TCP
 20 bytes of IP
 = 40 bytes + app
layer overhead
32 bits
head. type of
length
ver
len service
fragment
16-bit identifier flgs
offset
upper
time to
Internet
layer
live
checksum
total datagram
length (bytes)
for
fragmentation/
reassembly
32 bit source IP address
32 bit destination IP address
Options (if any)
data
(variable length,
typically a TCP
or UDP segment)
E.g. timestamp,
record route
taken, specify
list of routers
to visit.
Network Layer 4-19
DHCP: Dynamic Host Configuration Protocol
Goal: allow host to dynamically obtain its IP address
from network server when it joins network
Can renew its lease on address in use
Allows reuse of addresses (only hold address while connected
an “on”
Support for mobile users who want to join network (more
shortly)
DHCP overview:
 host broadcasts “DHCP discover” msg
 DHCP server responds with “DHCP offer” msg
 host requests IP address: “DHCP request” msg
 DHCP server sends address: “DHCP ack” msg
Network Layer 4-20
DHCP client-server scenario
A
B
223.1.2.1
DHCP
server
223.1.1.1
223.1.1.2
223.1.1.4
223.1.2.9
223.1.2.2
223.1.1.3
223.1.3.1
223.1.3.27
223.1.3.2
E
arriving DHCP
client needs
address in this
network
Network Layer 4-21
DHCP client-server scenario
DHCP server: 223.1.2.5
DHCP discover
arriving
client
src : 0.0.0.0, 68
dest.: 255.255.255.255,67
yiaddr: 0.0.0.0
transaction ID: 654
DHCP offer
src: 223.1.2.5, 67
dest: 255.255.255.255, 68
yiaddrr: 223.1.2.4
transaction ID: 654
Lifetime: 3600 secs
DHCP request
time
src: 0.0.0.0, 68
dest:: 255.255.255.255, 67
yiaddrr: 223.1.2.4
transaction ID: 655
Lifetime: 3600 secs
DHCP ACK
src: 223.1.2.5, 67
dest: 255.255.255.255, 68
yiaddrr: 223.1.2.4
transaction ID: 655
Lifetime: 3600 secs
Network Layer 4-22
NAT: Network Address Translation
rest of
Internet
local network
(e.g., home network)
10.0.0/24
10.0.0.4
10.0.0.1
10.0.0.2
138.76.29.7
10.0.0.3
All datagrams leaving local
network have same single source
NAT IP address: 138.76.29.7,
different source port numbers
Datagrams with source or
destination in this network
have 10.0.0/24 address for
source, destination (as usual)
Network Layer 4-23
NAT: Network Address Translation
 Motivation: local network uses just one IP address as
far as outside word is concerned:
 no need to be allocated range of addresses from ISP:
- just one IP address is used for all devices
 can change addresses of devices in local network
without notifying outside world
 can change ISP without changing addresses of
devices in local network
 devices inside local net not explicitly addressable,
visible by outside world (a security plus).
Network Layer 4-24
NAT: Network Address Translation
Implementation: NAT router must:



outgoing datagrams: replace (source IP address, port
#) of every outgoing datagram to (NAT IP address,
new port #)
. . . remote clients/servers will respond using (NAT
IP address, new port #) as destination addr.
remember (in NAT translation table) every (source
IP address, port #) to (NAT IP address, new port #)
translation pair
incoming datagrams: replace (NAT IP address, new
port #) in dest fields of every incoming datagram
with corresponding (source IP address, port #)
stored in NAT table
Network Layer 4-25
NAT: Network Address Translation
2: NAT router
changes datagram
source addr from
10.0.0.1, 3345 to
138.76.29.7, 5001,
updates table
2
NAT translation table
WAN side addr
LAN side addr
1: host 10.0.0.1
sends datagram to
128.119.40, 80
138.76.29.7, 5001 10.0.0.1, 3345
……
……
S: 10.0.0.1, 3345
D: 128.119.40.186, 80
S: 138.76.29.7, 5001
D: 128.119.40.186, 80
138.76.29.7
S: 128.119.40.186, 80
D: 138.76.29.7, 5001
3: Reply arrives
dest. address:
138.76.29.7, 5001
3
1
10.0.0.4
S: 128.119.40.186, 80
D: 10.0.0.1, 3345
10.0.0.1
10.0.0.2
4
10.0.0.3
4: NAT router
changes datagram
dest addr from
138.76.29.7, 5001 to 10.0.0.1, 3345
Network Layer 4-26
NAT: Network Address Translation
 16-bit port-number field:

60,000 simultaneous connections with a single
LAN-side address!
 NAT is controversial:
 routers
should only process up to layer 3
 violates end-to-end argument
• NAT possibility must be taken into account by app
designers, e.g., P2P applications
 address
IPv6
shortage should instead be solved by
Network Layer 4-27
IPv6
 Initial motivation: 32-bit address space
completely allocated by 2008.
 Additional motivation:
header format helps speed processing/forwarding
 header changes to facilitate QoS
 new “anycast” address: route to “best” of several
replicated servers

 IPv6 datagram format:
 fixed-length 40 byte header
 no fragmentation allowed
Network Layer 4-28
IPv6 Header (Cont)
Priority: identify priority among datagrams in flow
Flow Label: identify datagrams in same “flow.”
(concept of“flow” not well defined).
Next header: identify upper layer protocol for data
Network Layer 4-29
Other Changes from IPv4
 Checksum: removed entirely to reduce
processing time at each hop
 Options: allowed, but outside of header,
indicated by “Next Header” field
 ICMPv6: new version of ICMP
additional message types, e.g. “Packet Too Big”
 multicast group management functions

Network Layer 4-30