Download Chapter 7 - SaigonTech

Chapter 7
Network Architectures
Instructor: Nhan Nguyen Phuong
Contents
1.
2.
3.
4.
5.
6.
7.
Putting Data on the Cable: Access Methods
The Ethernet Architecture
Ethernet Standards
Ethernet Frame Types
The Token Ring Architecture
The AppleTalk Environment
The Fiber Distributed Data Interface (FDDI)
Architecture
8. Networking Alternatives
Guide to Networking Essentials, Fifth Edition
2
1. Putting Data on the Cable: Access
Methods
1.1. Function of Access Methods
1.2. Major Access Methods
1.3. Choosing an Access Method
Guide to Networking Essentials, Fifth Edition
3
• Given that network architectures communicate in a
number of different ways, some factors in network
communications must be considered
– How computers put data on the cable
– How they ensure that the data reaches its destination
undamaged
Guide to Networking Essentials, Fifth Edition
4
1.1. Function of Access Methods
• The way in which computers attached to a network
share the cable must be defined
• A collision results from two or more devices sending
a signal along the same channel at the same time
– Splitting data in small chunks helps prevent collisions
• Channel access methods specify when computers
can access the cable or data channel
– Ensure that data reaches destination by preventing
computers from sending messages that might collide
– Every computer on a network must use the same
access method
Guide to Networking Essentials, Fifth Edition
5
1.2. Major Access Methods
• Channel access is handled at the MAC sublayer of
the Data Link layer in the OSI model
• Five major types of channel access
–
–
–
–
–
Contention
Switching
Token passing
Demand priority
Polling
Guide to Networking Essentials, Fifth Edition
6
1.2.1. Contention
• In early networks based on contention, computers
sent data whenever they had data to send
• As networks grow, outgoing messages collide more
frequently, must be sent again, and then collide
again
• To organize contention-based networks, two carrier
access methods were created
– CSMA/CD
– CSMA/CA
Guide to Networking Essentials, Fifth Edition
7
a. Carrier Sense Multiple Access with Collision Detection
(CSMA/CD)
Guide to Networking Essentials, Fifth Edition
8
b. Carrier Sense Multiple Access with Collision Avoidance
(CSMA/CA)
• When the computer senses that no other computer
is using the network, it signals its intent to transmit
– Other computers with data to send must wait when
they receive the “intent-to-transmit” signal and send
their “intent-to-transmit” only when channel is free
• The overhead created by intent-to-transmit packets
reduces network speed significantly
• Used in wireless LANs with an access point
– Wireless NIC tells access point its intents to transmit
– Access point hears transmissions from all devices,
so it can determine whether it’s okay to transmit
Guide to Networking Essentials, Fifth Edition
9
1.2.2. Switching
• Switching: nodes are interconnected through a a
switch, which controls access to the media
– Contention occurs only when multiple senders ask to
reach the same receiver simultaneously or when the
simultaneous transmission requests exceed the
switch’s capability to handle multiple connections
• Advantages: fairer, centralized management
(enables QoS), switch can have connection ports
that operate at different speeds
• Disadvantage: higher cost
Guide to Networking Essentials, Fifth Edition
10
1.2.3. Token Passing
Guide to Networking Essentials, Fifth Edition
11
1.2.4. Demand Priority
• Demand priority: channel access method used
solely by the 100VG-AnyLAN 100 Mbps Ethernet
standard (IEEE 802.12)
– 100VG-AnyLAN runs on a star bus topology
– Intelligent hubs control access to the network
• Hub searches all connections in a round-robin fashion
• When an end node has data to send, it transmits a
demand signal to the hub
• The hub then sends an acknowledgement that the
computer can start transmitting its data
– The major disadvantage of demand priority is price
Guide to Networking Essentials, Fifth Edition
12
1.2.5. Polling
Guide to Networking Essentials, Fifth Edition
13
1.3. Choosing an Access Method
Guide to Networking Essentials, Fifth Edition
14
Guide to Networking Essentials, Fifth Edition
15
Guide to Networking Essentials, Fifth Edition
16
2. The Ethernet Architecture
2.1. Overview of Ethernet
2.2. Ethernet Operation
Guide to Networking Essentials, Fifth Edition
17
• 1960s and 1970s: many organizations worked on
methods to connect computers and share data
– E.g., the ALOHA network at the University of Hawaii
– 1972: Robert Metcalf and David Boggs, from Xerox’s
PARC, developed an early version of Ethernet
• 1975: PARC released first commercial version (3
Mbps, up to 100 computers, max. 1 km of total cable)
• DIX developed standard based on Xerox’s Ethernet
(10 Mbps)
• 1990: IEEE defined the 802.3 specification
– Defines how Ethernet networks operate at layers 1-2
Guide to Networking Essentials, Fifth Edition
18
2.1. Overview of Ethernet
• Ethernet is the most popular network architecture
– Advantages: easy to install, scalable, broad media
support, and low cost
– Supported transmission speeds: 10 Mbps to 10 Gbps
– Uses the NIC’s MAC address to address frames
– Ethernet variations are compatible with one another
• Basic operation and frame formatting is the same
• Cabling, speed of transmission, and method by which
bits are encoded on the medium differ
Guide to Networking Essentials, Fifth Edition
19
2.2. Ethernet Operation
• Ethernet is a best-effort delivery system
– It works at the Data Link layer of the OSI model
• Relies on the upper-layer protocols to ensure reliable
delivery of data
• Understanding the following concepts is important:
–
–
–
–
How Ethernet accesses network media
Collisions and collision domains
How Ethernet handles errors
Half-duplex and full-duplex communications
Guide to Networking Essentials, Fifth Edition
20
2.2.1. Accessing Network Media
• Ethernet uses CSMA/CD in a shared-media
environment (a logical bus)
– Ethernet device listens for a signal or carrier (carrier
sense) on the medium first
– If no signal is present, no other device is using the
medium, so a frame can be sent
– Ethernet devices have circuitry that detects collisions
and automatically resends the frame that was
involved in the collision
Guide to Networking Essentials, Fifth Edition
21
2.2.2. Collisions and Collision Domains
Guide to Networking Essentials, Fifth Edition
22
2.2.3. Ethernet Error Handling
• Collisions are the only type of error for which
Ethernet automatically attempts to resend the data
• Errors can occur when data is altered in medium
– Usually caused by noise or faulty media connections
– When the destination computer receives a frame,
the CRC is recalculated and compared against the
CRC value in the FCS
– If values match, the data is assumed to be okay
– If values don’t match, the data was corrupted
• Destination computer discards the frame
• No notice is given to the sender
Guide to Networking Essentials, Fifth Edition
23
2.2.4. Half-Duplex Versus Full-Duplex
Communications
• When half-duplex communication is used with
Ethernet, CSMA/CD must also be used
• When using a switched topology, a computer can
send and receive data simultaneously (full-duplex
communication)
– The collision detection circuitry is turned off because
collisions aren’t possible
– Results in a considerable performance advantage
Guide to Networking Essentials, Fifth Edition
24
3. Ethernet Standards
3.1. 100 Mbps IEEE Standards
3.1. 10 Mbps IEEE Standards
3.3. Gigabit Ethernet: IEEE 802.3ab and 802.3z Standards
3.4. What’s Next for Ethernet?
Guide to Networking Essentials, Fifth Edition
25
• Each Ethernet variation is associated with an IEEE
standard
• The following sections discuss many of the
standards, some of which are obsolete or had
limited use
• Keep in mind that Ethernet over UTP cabling has
been the dominant technology since the early
1990s, and will likely to continue to be for the
foreseeable future
Guide to Networking Essentials, Fifth Edition
26
3.1. 100 Mbps IEEE Standards
• The most widely accepted Ethernet standard today
is 100BaseT, which is also called fast Ethernet
– The current IEEE standard for 100BaseT is 802.3u
• Subcategories:
– 100BaseTX: Two-pair Category 5 or higher UTP
– 100BaseT4: Four-pair Category 3 or higher UTP
– 100BaseFX: Two-strand fiber-optic cable
– Because of its widespread use, the cable and
equipment in fast Ethernet are inexpensive
– Architecture of choice for all but heavily used servers
and multimedia applications
Guide to Networking Essentials, Fifth Edition
27
3.1.1. 100BaseTX
• 100BaseTX is the standard that’s usually in mind
when discussing 100 Mbps Ethernet
• Requires two of the four pairs bundled in a
Category 5 twisted-pair cable
• Although three cable types are available for
100BaseT, 100BaseTX is the most widely
accepted
– Generally called fast Ethernet
Guide to Networking Essentials, Fifth Edition
28
3.1.2. 100BaseT4
• 100BaseT4 Ethernet uses all four pairs of wires
bundled in a UTP cable
• Advantage: capability to run over Category 3 cable
– One of the biggest expenses of building a network is
cable installation, so many organizations with
Category 3 cabling chose to get the higher speed
with the existing cable plant by using 100BaseT4
instead of 100BaseTX
Guide to Networking Essentials, Fifth Edition
29
3.1.3. 100BaseFX
• 100BaseFX uses two strands of fiber-optic cable
– Advantages:
• Impervious to electrical noise and electronic
eavesdropping
• Can span much greater distances between devices
– Disadvantage: far more expensive than twisted-pair
– Rarely used as a complete 100BaseTX replacement
• Used as backbone cabling between hubs or switches
and to connect wiring closets between floors or
buildings
• Connect client or server computers to the network
when immunity to noise and eavesdropping is
required
Guide to Networking Essentials, Fifth Edition
30
3.1.4. 100BaseT Design Considerations
Guide to Networking Essentials, Fifth Edition
31
Guide to Networking Essentials, Fifth Edition
32
3.2. 10 Mbps IEEE Standards
• Four major implementations of 10 Mbps Ethernet
–
–
–
–
10Base5: Ethernet using thicknet coaxial cable
10Base2: Ethernet using thinnet coaxial cable
10BaseT: Ethernet over UTP cable
10BaseF: Ethernet over fiber-optic cable
• Of these 10 Mbps standards, only 10BaseT and
10BaseF are seen today
• 10Base2 and 10Base5 are essentially obsolete
Guide to Networking Essentials, Fifth Edition
33
3.2.1. 10BaseT
Guide to Networking Essentials, Fifth Edition
34
3.2.2. 10BaseF
Guide to Networking Essentials, Fifth Edition
35
3.3. Gigabit Ethernet: IEEE 802.3ab and
802.3z Standards
• Gigabit Ethernet implementations
– 802.3z-1998 covers 1000BaseX specifications,
including the L (long wavelength laser/fiber-optic), S
(short wavelength laser/fiber-optic), and C (copper
jumper cables)
– 802.3ab-1999 covers 1000BaseT specifications,
which require four pairs of 100 ohm Category 5 or
higher cable
Guide to Networking Essentials, Fifth Edition
36
3.3.1. 1000BaseT
Guide to Networking Essentials, Fifth Edition
37
3.3.2. 1000BaseLX
Guide to Networking Essentials, Fifth Edition
38
3.3.3. 1000BaseSX
Guide to Networking Essentials, Fifth Edition
39
3.3.4. 1000BaseCX
Guide to Networking Essentials, Fifth Edition
40
3.3.5. 10 Gigabit Ethernet: 10 Gbps IEEE
802.3ae Standard
• Defined to run only on fiber-optic cabling, both SMF
and MMF, on a maximum distance of 40 km
– Provides bandwidth that can transform how WAN
speeds are thought of
• Runs in full-duplex mode only
– CSMA/CD is not necessary
• Primary use: as network backbone
– It also has its place in storage area networks (SANs)
– Will be the interface for enterprise-level servers
Guide to Networking Essentials, Fifth Edition
41
• Standards
– 10GBASE-SR: Runs over short lengths (between 26
and 82 meters) over MMF
• For high-speed servers, SANs, etc.
– 10GBASE-LR: Runs up to 10 km on SMF
• For campus backbones and MANs
– 10GBASE-ER: Runs up to 40 km over SMF
• Primary applications are for MANs
– 10GBASE-SW: Uses MMF for distances up to 300 m
– 10GBASE-LW: Uses SMF for distances up to 10 km
– 10GBASE-EW: Uses SMF for distances up to 40 km
Guide to Networking Essentials, Fifth Edition
42
3.4. What’s Next for Ethernet?
• Implementations of 40 Gbps Ethernet are underway
• Ethernet could increase tenfold every 4-6 years
– 100 Gbps Ethernet available by 2006 to 2008, terabit
Ethernet by 2011, and 10 terabit Ethernet by 2015
• In October 2005, Lucent Technologies
demonstrated for the first time the transmission of
Ethernet over fiber-optic cable at 100 Gbps
– It will be able to transfer data across the city faster
than today’s CPUs can transfer data to memory
– This level of speed has major implications for the
entertainment industry and many other areas
Guide to Networking Essentials, Fifth Edition
43
4. Ethernet Frame Types
4.1. Ethernet 802.3
4.2. Ethernet 802.2
4.3. Ethernet SNAP
4.4. Ethernet II
4.5. Wireless Ethernet: IEEE 802.11b, a, and g
Guide to Networking Essentials, Fifth Edition
44
• Ethernet supports four non-compatible frame types
– Ethernet 802.3: used by IPX/SPX on Novell NetWare
2.x and 3.x networks
– Ethernet 802.2: used by IPX/SPX on Novell NetWare
3.12 and 4.x networks
• Supported by default in Microsoft NWLink
– Ethernet SNAP: used in EtherTalk and mainframes
– Ethernet II is used by TCP/IP
• All Ethernet frame types support a packet size
between 64 and 1518 bytes, and can be used by all
network architectures mentioned previously
Guide to Networking Essentials, Fifth Edition
45
4.1. Ethernet 802.3
Guide to Networking Essentials, Fifth Edition
46
4.2. Ethernet 802.2
• Ethernet 802.2 frames comply completely with the
Ethernet 802.3 standard
• The IEEE 802.2 group didn’t address Ethernet,
only the LLC sublayer of the OSI model’s layer 2
– Since Novell had already decided to use the term
Ethernet 802.3 to describe Ethernet raw, it’s
generally accepted that Ethernet 802.2 means a fully
802.3- and 802.2-compliant Ethernet frame
• Ethernet 802.2 frames contain similar fields to
802.3, with three additional LLC fields
Guide to Networking Essentials, Fifth Edition
47
4.3. Ethernet SNAP
• Ethernet SubNetwork Address Protocol (SNAP)
is generally used on the AppleTalk Phase 2
• It contains enhancements to the 802.2 frame,
including a protocol type field, which indicates the
network protocol used in the frame’s data section
Guide to Networking Essentials, Fifth Edition
48
4.4. Ethernet II
Guide to Networking Essentials, Fifth Edition
49
4.5. Wireless Ethernet: IEEE 802.11b, a,
and g
• AP serves as the center of a star topology network
• Stations can’t send and receive at the same time
– CSMA/CA is used instead of CSMA/CD
• 802.11b/a/g use handshaking before transmission
– Station sends AP an RTS and it responds with CTS
• Standards define a maximum transmission rate, but
speeds might be dropped to increase reliability
• No fixed segment length
– Maximum of 300 feet without obstructions
• Can be extended with large, high-quality antennas
Guide to Networking Essentials, Fifth Edition
50
5. The Token Ring Architecture
5.1. Token Ring Function
5.2. Hardware Components
5.3. Cabling in a Token Ring Environment
Guide to Networking Essentials, Fifth Edition
51
Guide to Networking Essentials, Fifth Edition
52
5.1. Token Ring Function
• A token passes around the ring
– If an “in use” token is received from NAUN, and the
computer has data to send, it attaches its data to the
token and sends it to its NADN
– If received token is in use, NIC verifies if it is the
destination station
• If not, the computer re-creates the token and the data
exactly and sends them to its NADN
• If it is, data is sent to the upper-layer protocols
– Two bits in data packet are toggled and token is
sent to NADN; when original sender receives it, it
frees the token and then passes it along
Guide to Networking Essentials, Fifth Edition
53
Beaconing
Guide to Networking Essentials, Fifth Edition
54
5.2. Hardware Components
• A hub can be a multistation access unit (MSAU)
or smart multistation access unit (SMAU)
• IBM’s token ring implementation is the most
popular adaptation of the IEEE 802.5 standard
– Minor variations but very similar to IEEE specs
• IBM equipment is most often used
– 8228 MSAU has 10 connection ports, eight of which
can be used for connecting computers
– The RO port on one hub connects to RI port on the
next hub, and so on, to form a ring among the hubs
• IBM allows connecting 33 hubs
Guide to Networking Essentials, Fifth Edition
55
5.3. Cabling in a Token Ring Environment
Guide to Networking Essentials, Fifth Edition
56
Guide to Networking Essentials, Fifth Edition
57
6. The AppleTalk Environment
6.1. LocalTalk
6.2. EtherTalk and TokenTalk
Guide to Networking Essentials, Fifth Edition
58
• Designed for use in Macintosh networks (1983)
• Can be run over several physical architectures;
commonly run over Ethernet (EtherTalk)
• Easy to implement
• Dynamic scheme used to determine device’s
address
• AppleTalk Phase 1 supported only 32 computers
per network, and only with LocalTalk cabling
– With hubs/repeaters, increased the number to 254
• AppleTalk Phase 2, EtherTalk, and TokenTalk
(1989) allow more than 16 million computers
Guide to Networking Essentials, Fifth Edition
59
6.1. LocalTalk
• LocalTalk uses STP in a bus topology to allow
users to share peripherals and data in a small
home or office environment
– CSMA/CA channel access method
• Avoids more collisions, but cumbersome
– Maximum transmission speed of 230.4 Kbps
• Thus, this architecture was used primarily in small,
Macintosh-only environments
Guide to Networking Essentials, Fifth Edition
60
6.2. EtherTalk and TokenTalk
• EtherTalk is the AppleTalk protocol running over a
10 Mbps IEEE 802.3 Ethernet network
• TokenTalk is the AppleTalk protocol running over
a 4 or 16 Mbps IEEE 802.5 token ring network
• Both implementations require using a different NIC
– Since 1996, Apple Computer has offered systems
with built-in Ethernet NICs or with options to add
Ethernet or token ring to its systems at a low cost
– Mac OS X with an Ethernet interface can freely
participate in a Windows-based network
Guide to Networking Essentials, Fifth Edition
61
7. The Fiber Distributed Data Interface
(FDDI) Architecture
Guide to Networking Essentials, Fifth Edition
62
Guide to Networking Essentials, Fifth Edition
63
8. Networking Alternatives
8.1. Broadband Technologies
8.2. Broadcast Technologies
8.3. Asynchronous Transfer Mode (ATM)
8.4. ATM and SONET Signaling Rates
8.5. High Performance Parallel Interface (HIPPI)
Guide to Networking Essentials, Fifth Edition
64
• Many other network architectures are available
• Some are good for specialized applications, and
others are emerging as new standards
• Topics
–
–
–
–
–
Broadband technologies (cable modem and DSL)
Broadcast technologies
ATM
ATM and SONET Signaling Rates
High Performance Parallel Interface (HIPPI)
Guide to Networking Essentials, Fifth Edition
65
8.1. Broadband Technologies
• Baseband systems use a digital encoding scheme
at a single fixed frequency
• Broadband systems use analog techniques to
encode information across a continuous range of
values
– Signals move across the medium in the form of
continuous electromagnetic or optical waves
– Data flows one way only, so two channels are
necessary for computers to send and receive data
– E.g., cable TV
Guide to Networking Essentials, Fifth Edition
66
8.1.1. Cable Modem Technology
Guide to Networking Essentials, Fifth Edition
67
8.1.2. Digital Subscriber Line (DSL)
• Competes with cable modem for Internet access
– Broadband technology that uses existing phone lines
to carry voice and data simultaneously
– Most prominent variation for home Internet access is
Asymmetric DSL (ADSL)
• Splits phone line in two ranges: Frequencies below 4
KHz are used for voice transmission, and frequencies
above 4 KHz are used to transmit data
• Typical connection speeds for downloading data
range from 256 Kbps to 8 Mbps; upload speeds are in
the range of 16 Kbps to 640 Kbps
Guide to Networking Essentials, Fifth Edition
68
8.2. Broadcast Technologies
• By definition: one-way transmissions
– This changed in Internet access by satellite
television systems
• Work on the principle that most traffic a user
generates is to receive files, text, and graphics
– The average user’s computer sends very little traffic
– User connects to service provider through a modem
– Service provider sends data by satellite to the user’s
home at speeds up to 400 Kbps
– E.g., service offered by DirectTV, through its
DirectPC add-on products
Guide to Networking Essentials, Fifth Edition
69
8.3. Asynchronous Transfer Mode (ATM)
• High-speed network technology for LANs and WANs
– Connection-oriented switches
• Dedicated circuits are set up before communicating
– Data travels in fixed-size 53-byte cells (5 byte-header)
• Enables ATM to work at extremely high speeds
– Quick switching
– Predictable traffic flow
• Enables ATM to guarantee QoS
– Used quite heavily for the backbone and
infrastructure in large communications companies
– LAN emulation (LANE) required for LAN applications
Guide to Networking Essentials, Fifth Edition
70
8.4. ATM and SONET Signaling Rates
Guide to Networking Essentials, Fifth Edition
71
8.5. High Performance Parallel Interface
(HIPPI)
• HIPPI (late 1980s): high-speed interface developed
for supercomputers and high-end workstations
– Serial HIPPI is a fiber-optic version that uses pointto-point optical links for bandwidth up to 800 Mbps
• In early 1990s, it was used as a network backbone
and for interconnecting supercomputers
– With the advent of Gigabit Ethernet, interest in HIPPI as
a LAN backbone decreased
– HIPPI-6400 (1998): up to 6.4 Gbps transfer rates
• Known as Gigabyte System Network (GSN)
– HIPPI and GSN are now exotic networking products
and aren’t often found in typical corporate networks
Guide to Networking Essentials, Fifth Edition
72
Summary
• Cable access methods determine how a network
architecture gains access to the network medium
• A network architecture defines how data is placed,
transmitted, and at what speed, and how problems in
the network are handled
• DIX introduced Ethernet, which later became the
IEEE 802.3 standard, transmitting data at 10 Mbps
– Standards for 10Mbps, 100Mbps, 1000Mbps (Gigabit),
and 10G indicate the supported network mediums
• 10 Gigabit Ethernet runs only over fiber-optic cable and
only in full-duplex mode
Guide to Networking Essentials, Fifth Edition
73
• Token ring networks are reliable, fast, and efficient
– Capable of transmitting at 4 Mbps or 16 Mbps
• Macintosh computers use AppleTalk to communicate
• FDDI is an extremely reliable, fast network
architecture that uses dual counter-rotating rings
• Cable modem technology delivers high-speed
Internet access to homes and businesses
• ATM, a high-speed network technology designed
both for LANs and WANs, uses connection-oriented
switches
Guide to Networking Essentials, Fifth Edition
74