Download Software Fault Tolerance – The big Picture

Survey
yes no Was this document useful for you?
   Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Document related concepts

Distributed firewall wikipedia , lookup

VMEbus wikipedia , lookup

Airborne Networking wikipedia , lookup

Internet protocol suite wikipedia , lookup

IEEE 1355 wikipedia , lookup

Bus (computing) wikipedia , lookup

I²C wikipedia , lookup

Recursive InterNetwork Architecture (RINA) wikipedia , lookup

Distributed operating system wikipedia , lookup

UniPro protocol stack wikipedia , lookup

CAN bus wikipedia , lookup

Transcript
Distributed RT Systems
Introduction
ITV Multiprogramming and Real-Time Systems
Anders P. Ravn
Aalborg University
April 2009
Prerequisites
• Understanding of Real-Time Systems for
monoprocessor systems
• Understanding of Distributed Systems
Aims
• Understanding the issues in combining RT
and Distributed Architectures
• Ability to model and analyse such systems
• To stimulate research interest
What is a real-time system?
• A real-time system is a computerized system
that must respond to externally generated
input within specified time bounds
• The computer is a component in a larger
engineering system -
EMBEDDED COMPUTER SYSTEM
A simple fluid control system
Interface
Input flow
reading
Pipe
Flow meter
Processing
Output valve
angle
Computer
Valve
A distributed fluid control system
Interface
Input flow
reading
Pipe
Flow meter
Processing
Output valve
angle
Computers and Network
Valve
The Periodic Control Task
Tightly Coupled :
LOOP
wait_until(t)
read_sensor;
compute;
write_actuator;
t = t+T;
END
OR
Distributed:
LOOP
wait_until(t)
read_sensor;
send reading;
t = t+T;
END
LOOP
get reading;
compute;
send setting
END
LOOP
get setting
write_actuator;
END
The R-T Constraints
Have not changed !
Terminology
• Soft real-time
• Firm real-time
Value of response
• Hard real-time
D
D
D may be missed occasionally
Time
Time
RTS Design
Essentially:
Specification of a collection of periodic and sporadic tasks.
Tasks may share resources, but must not block explicitly.
Formalisms:
• UML-RT
• RT- HOOD
NEW:
•Selection and Analysis of network
OR
•Selection of a Distributed R-T platform
Validation
1. Verification
2. Testing
3. Simulation
ON
1. Model
2. Prototype with Test harness
3. Real System
Characteristics of a RTS
•
•
•
•
Timing Constraints
Dependability Requirements
Concurrent control of separate components
Facilities to interact with special purpose
hardware
Have not changed !
Analysis Tools
• Response Time Analysis for Networks and
processors (BW 14.7)
• Model checking of Networks of Timed
Automata (UppAal)
• Simulation Tools
Platforms
• Time Triggered Architecture (BW p. 568)
• CORBA-RT (BW 14.4.4)
Distributed Algorithms
• Clock Synchronization (BW 14.6.2)
• Fault Tolerance (BW 14.5)
Networks
•
•
•
•
•
•
•
CAN
TT-CAN
TTP/C Protocol
ARINC 629
WorldFIP
PROFIBUS
…
CAN
• initial target automotive applications
• a multi-master architecture
• a broadcast shared bus,
• the transmission medium is usually a twisted pair cable
• network maximum length depends on the data rate (e.g. 40m @ 1
Mbps; 1300m @ 50 Kbps)
• The arbitration uses a CSMA non-destructive bit-wise protocol in
which the controller transmitting the message with lowest identifier
wins access to the medium and continues transmission.
• The remaining controllers detect a collision back off and retry again
• The traffic scheduling at the bus access level is thus based on fixed
priorities. applications.
• The addressing is indirect and based on the identifiers, too.
• The CAN protocol does not specify an application layer.
TTP/C Protocol
•
•
•
•
•
•
•
•
•
•
a fault-tolerance oriented communication protocol
clock synchronization
membership service
fast error detection and consistency checks
. A network consists of a set of communicating nodes connected by a
replicated network
. A node comprises a host computer and a TTP/C communication controller.
The medium access control is based on TDMA with bus time divided into
slots, each statically assigned to one node. In each slot each node transmits
one frame. The frame cycle is called a
Messages are piggybacked within the frames transmitted by each node.
The protocol defines 4 transmission speed classes ( 500Kbps, 1Mbps, 2Mbps
and more recently 25Mbps)
an application layer that delivers configuration and messaging services.
Middleware
• Masks system and network heterogeneity
• Hides complexity of distributed systems
CORBA
• Minimum CORBA
• Asynchronous Method Invocation
• Real-Time CORBA
Real Time CORBA
• Policies and mechanisms for specifying end-toend application QoS requirements.
• QoS enforcement from real-time operating
systems and networks.
• Optimized real-time communication protocols
• Optimized real-time request demultiplexing and
dispatching.
• Optimized memory management.
• Optimized presentation layer
AMI
• allows exchange of asynchronous requests
• Static Invocation Interface (SII)
• Polling model: each two-way operation returns a
local object Poller. A client can use the Poller to
check the status of a request.
• Callback model: when a client invokes a two-way
asynchronous operation on an object, it passes an
reference for a reply handler servant as a
parameter.
Message Oriented Middleware
• Java Message Service (JMS)
• Data Distribution Service for Real-Time
systems (DDS)
The CAN bus
Physical Layer
• Serial bus
• Electrical properties and timing see:
http://www.semiconductors.bosch.de/en/20/can/3-literature.asp
• Dominant and Recessive encoding:
dominant is logical 0
recessive is logical 1
simultanous transmission gives logical AND
Frame Format
Field name
Length (bits)
Purpose
Start-of-frame
1
Dominant 0
Identifier
11
Sender id
RTR
1
Dominant 0
Identifier extension
1
Dominant 0
Reserved
1
Data length (bytes)
4
Data field
0 - 64
CRC15
15
CRC delimiter
1
ACK
1
ACK delimiter
1
Recessive 1
End-of-frame
7
Recessive 1
0-8
Recessive 1
Medium Access Control
Hanz p. 6
Simple Analysis
• One process per processor
• No error handling
 Ri 
Ri  Bi  Ci    C j
jhp ( i )  T j 
Hanz p. 10, CAN bus paper
Simple Analysis
Ci  33 # bytes  8
Bi  max( C j ) for j  lp (i )
 Ri 
Ri  Bi  Ci    C j
jhp ( i )  T j 
Hanz p. 10, CAN bus paper
Extended Analysis
j in hp(i)
Remarks
• There is no easy way of finding an optimal
assignment for the extended case!
• The formulas are too pessimistic M, Crossinterference
• Experimental validation.
FTT-CAN
• Static versus Dynamic Traffic Scheduling
• Event versus Time Triggered Communication
FFT-CAN E-cycle
Overhead
Synchronous Messaging System
SRT entries:
• DLC
– data length
• C
- max transmission time
• Ph
- relative phase
• P
- Period measured in E’s (T)
• D
- Deadline
• Pr
- fixed priority
For Each E-cycle
• A synchronous schedule is broadcast with
the EC-Trigger Message
• Plan based scheduling
• On-line scheduling
Schedulability Analysis
Blocking free non-preemptive scheduling
RM:
EDF:
Asynchronous Messaging System
ART entries:
• DLC
– data length
• C
- max transmission time
• MIT
- min interarrival time in E’s
• D
- Deadline
• Pr
- fixed priority
Schedulability Analysis
Remarks
• Transmission errors not treated
• Master selection not treated