Download Cable/DSL 4-Port Router

1
Connect the Cable/DSL 4-Port
Router to Your Network
The following steps will walk you through connecting the Router, configuring your networked PCs to accept the IP addresses the Router assigns them,
and configuring the Router with setting(s) provided by your Internet Service
Provider (ISP).
This Quick Installation is meant to help you install the Router quickly and easily. For detailed instructions on installation and
configuration and further setup options, please consult the User Guide.
Cable/DSL 4-Port Router
The installation technician from your ISP should have left the setup information for your modem with you after installing your broadband connection.
If not, you can call your ISP to request the data.
Once you have the setup information you need for your specific type of
Internet connection, you can begin installation and setup of the Router.
Important: Network Everywhere strongly recommends that you use the
Setup Wizard CD-ROM by inserting the Setup Wizard CD-ROM into your
PC’s CD-ROM drive. The Setup Wizard will start automatically. Then follow
the Setup Wizard’s instructions to install the Router.
However, if you prefer to manually install the Router, then proceed to step A
of this Quick Installation. Follow these instructions to install the Router.
For more detailed instructions, please refer to the Cable/DSL 4-Port Router’s
User Guide on the Setup Wizard CD-ROM.
A. Make sure that all the devices you’ll be working with are powered down,
including your PCs, your cable or DSL modem, and the Router.
B. Connect an Ethernet network
cable to one of your PCs’
Ethernet ports. This will be the
port that connects to the
Router.
Minimum Requirements
• PC with CD-ROM Drive
• Network Adapter with Ethernet (UTP CAT 5)
Cabling and TCP/IP Protocol Installed per PC
• Internet Explorer 4.0 (or Higher) or Netscape
Navigator 4.7 (or Higher) for Web-based
Configuration
• Cable or DSL Modem with Ether net
Connection and Internet Access
Package Contents
(1) Cable/DSL 4-Port Router
(2) Power Adapter
(3) Setup Wizard CD-ROM with User Guide
Not Shown:
Registration Card and this Quick
Installation
C. Connect the other end of the
Ethernet network cable to one
of the LAN ports on the back
of the Cable/DSL Router.
Repeat steps A and B for all
the PCs you wish to connect to
the Router.
E
F. Plug one end of the power
adapter into the Power port
located on the back of the
Router.
F
G. Plug the other end of the power adapter into an appropriate power socket.
Note: Always use the power adapter that came with the Router. Using any
other power adapter could result in product damage.
B
NR041
E. Connect the network cable
from your cable or DSL
modem to the Router’s
Internet port, and connect your
cable or DSL modem to its
proper connection. Then
power up your modem.
H. Turn on the cable or DSL modem. Then turn on the PC.
2
C
D. Port 1 can act as the Router’s uplink port. If you are connecting Port 1 of
the Router to a hub or switch, press the Uplink pushbutton. If you are connecting Port 1 of the Router to a PC, make sure the Uplink pushbutton has
not been pressed.
Configure Your PCs to Connect to
the Cable/DSL 4-Port Router
Before setting up the Router, you will have to configure your PCs to accept
the IP addresses provided by the Router. To do this, you will need to configure TCP/IP. These instructions apply only to Windows 95, 98, and
Millennium machines. For TCP/IP setup under Windows NT, 2000, and XP,
please refer to your Windows manual.
Continue to Step 2 now!
A. Go
to
the
Network
Configuration screen by clicking the Windows Start button,
selecting Settings, and selecting
the Control Panel. Then doubleclick the Network icon.
3
Now that the Router is connected to your network, and you’ve set up TCP/IP
on your PCs, you can begin configuring the Router.
B. In the Configuration window,
select the TCP/IP protocol line
that has been associated with
your network card/adapter. If
there is no TCP/IP line listed,
refer to the User Guide to install
the TCP/IP Protocol now.
C. Click the Properties button,
and choose the IP Address tab.
Select Obtain an IP address
automatically. Click the OK
button. You have completed the
client settings.
A. Open your web browser and type
http://192.168.1.1 into the
browser’s Address field. Press the
Enter key.
B
A
C
F. If you want to use the Router as a DHCP server, choose the DHCP tab,
and configure the DHCP settings for your network.
DHCP If your ISP supports DHCP, select this default option.
Static (Fixed) IP Address If your ISP assigns you a static IP Address, fill
in the WAN IP Address, Subnet Mask, Default Gateway Address, and
DNS fields.
PPPoE Enter your user name and password, if applicable.
B. An Enter Network Password screen
will appear. Leave the User Name
field blank, and enter admin (the
default password) in the Password
field. Then click the OK button.
C. The Router’s Setup tab will
appear. Based on the setup
instructions from your ISP, you
may need to provide the Host
Name and Domain
Name.
These fields allow you to supply
a host and domain name for the
Router and are usually left blank.
If requested by your ISP (usually
cable ISPs), complete these two
fields.
The values for the Router’s LAN IP Address and Subnet Mask are shown
on the Setup screen. Unless you have specific internal needs, there should
be no reason to change these values. For the internal LAN, the default values are as follows.
•
Device IP Address: 192.168.1.1
•
Subnet Mask:
255.255.255.0
D. The Router supports three WAN Connection Types: DHCP (obtain an IP
automatically), Static IP Address, and PPPoE.
When you have properly configured the Setup tab, click the Apply button, and then click the Continue button.
B
D. Click the OK button. Windows
may ask for original Windows
installation or additional files.
Supply them as needed (e.g.,
D:\win98, D:\win95, c:\windows\options\cabs, etc.).
E. Windows will ask you to restart
the PC. Click the Yes button. If
Windows does not ask you to
restart, restart your PC at this
time.
Configure the Cable/DSL 4-Port
Router
E. Click the Password tab, and set a password for the Router. You can use up
to 64 alphanumeric characters. The default password is admin. If you
don’t change the password, all users on your network will be able to access
the Router using the default password. When finished making your
changes, click the Apply button, and then click the Continue button.
F
G. Unless you already have a DHCP server on your internal network, choose
Enable. By choosing Enable, you will configure the Router to automatically assign IP addresses to each of your PCs. You may enter the number
of PCs you plan on networking to the Router in the Number of DHCP
Users field.
H. Click the Apply button, and then click the Continue button.
I. Reset the power on the cable or DSL modem, and then restart the computer so the computer can obtain the Router’s new settings.
The installation of the Cable/DSL 4-Port Router is complete.
If you wish to further customize its configuration or want additional
details, refer to the User Guide on the Setup CD-ROM.
C
Note: The Setup screen and its available features may vary depending on the
WAN Connection Type you select.
E
Important: Network Everywhere strongly recommends that you use the Setup
Wizard CD-ROM to install the Router.
QI-NR041-062402A JL
www.networkeverywhere.com