Download manual spitfire 3x prism-scope 13a

Survey
yes no Was this document useful for you?
   Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Document related concepts
no text concepts found
Transcript
The Vortex Spitfire 3x Prism Scope
®
The perfect choice for the AR platform, the Vortex Spitfire® 3x prism
scope combines a compact, prism-based design with the intuitive glassetched EBR-556B reticle—providing vital speed, accuracy and versatility
in close to medium range shooting scenarios.
Battery
Compartment
Elevation
Adjustment
Flip Cap Lens
Cover
Ocular
Lens
Reticle Focus
Windage
Adjustment
Objective
Lens
Picatinny Rail
Dual Use: Shooting Tactical / Hunting
— Please read entire manual before using your new optic.
Patent Pending
2
3
Controls and Adjustments
Prism Scope Adjustments
Battery Installation
Reticle Focus
Remove the battery compartment cover using a coin
or screwdriver. Install and orient the CR 2032 battery
so the positive side (+) faces upward, then replace the
cover. When replacing the cover, be sure it is fully
screwed down with the o-ring seal in place.
This Vortex Spitfire prism scope uses a fast focus eyepiece designed to
quickly and easily provide a sharply focused
reticle.
To adjust the reticle focus:
• Look through the scope at a blank white
wall or up at the sky.
Illumination Control
The reticle can be used without illumination. To
activate the reticle illumination, rotate the illumination dial to the left or
right. The dial shows both red and green numbers, indicating five levels of
brightness. Rotate the dial so the number indicating the desired color and
intensity faces the shooter.
Rotate dial to
set the preferred
color and intensity.
Note: Be sure to turn the dial
to zero when done shooting to
avoid running the battery down
prematurely.
• Turn the eyepiece focus dial in or out until
the reticle image is as crisp as possible.
Adjust the reticle focus.
• Note: Try to make this particular
adjustment quickly, as the eye will try to compensate for an out-offocus reticle.
Once this adjustment is complete, it will not be necessary to re-focus
every time you use the scope. However, because your eyesight may
change over time, you should re-check this adjustment periodically.
Warning
Looking directly at the sun through a scope, or any optical instrument,
can cause severe and permanent damage to your eyesight.
4
5
Windage and Elevation Adjustments
Mounting the Spitfire
The Spitfire incorporates elevation and windage dials with audible
Orient the Spitfire so the illumination dial faces shooter.
clicks. Each small click will move the point of impact 1/2 Minute of
Angle (MOA). 1/2 MOA will closely correspond to 1/8 inch at 25 yards,
1/4 inch at 50 yards, 1/2 inch at 100 yards and 1 inch at 200 yards.
Adjust the settings
• Remove the dial covers.
• Use a coin or screwdriver to make the adjustments.
• Turn the adjustment dial in the appropriate direction as indicated
by the arrows. Move the dials in the direction you wish the bullet’s
point-of-impact to change.
Elevation
Rotate the adjustment dial in the
direction you wish the bullet’s
point-of-impact to change. For
example, turning the turret
counter-clockwise will move the
point-of-impact up or to the right.
Windage
1.Loosen the two base
clamp hex nuts and
attach the Spitfire to the
rail/base, making sure
that recoil lugs are solidly
seated in base grooves.
2.Checking that the
mount fully engages the
base, press the Spitfire
down and forward, then
tighten and torque the
base clamp hex nuts.
Mount Riser
Base Clamp
Mount Screw
Base Clamp
Hex Nut
Note: To prevent recoil injury, position it so that you have at least two
inches of eye relief once the Spitfire scope is attached. Be sure you can see
the full field of view through the scope before tightening down the mount.
Recommended Torque
Example
Base Clamp Hex Nuts 35–45 in/lbs
At a 50 yard sight-in distance, it will take four clicks of the dial to move the
bullet’s point-of-impact one inch.
Mount Heights
6
The Spitfire comes from the factory with a mounted height of 40.4 mm
from the optic center to base surface. This is commonly referred to as a
lower 1/3 co-witness height. If a lower 30 mm mounted height is desired,
loosen the two mount screws then remove the base clamp and mount riser.
Remove the mount riser and reinstall the base clamp with the shorter
mount screws provided in the box using a non-permanent thread-locking
compound when installing the screws.
7
Sighting in
Shooting with the Spitfire
Bore Sighting
Your Spitfire 3x scope is equipped with the EBR-556B Enhanced Battle
Reticle. Although this precision reticle has been designed around the
popular 5.56x45 (.223 Remington) cartridge using a 55 grain bullet and
16-inch barrel, it can also be used effectively with many other cartridges
and barrel lengths. Be aware that the more a cartridge varies in bullet drop
from the 5.56 round, the greater the difference will be in the referenced
yardage numbers.
After mounting, an initial bore sighting of the Spitfire at short range
(25–50 yards) will save time and money at the range. This can be done
using a bore sighter according to the manufacturer’s instructions, or by
removing the bolt on some rifles and visually sighting through the barrel.
To visually bore sight a rifle:
1.Place the rifle solidly on a rest and remove the bolt.
2.Sight through the bore and center the target inside the barrel.
3.With the bull’s eye centered in the bore, make windage and
elevation adjustments until the center dot is aligned over the bull’s eye.
Final Range Sight-In
Final sight-in should be done at the range using the exact ammunition
you expect to hunt or shoot with:
1.After the Spitfire has been bore sighted, fire a shot or two at
your desired zero distance to check that you’re roughly on target.
If necessary, adjust the dot to put you near the center of the target (see
Windage and Elevation Adjustment on page 6).
2.Fire a three-shot group as precisely as possible.
3.Using the center of this group as a reference, make any necessary
adjustments for windage and elevation correction. Using arrows for
reference, adjust dials in the direction you wish the group to move.
The main crosshair intersection of the EBR-556B reticle is intended to be
zeroed at 100 yards (see Sighting In on page 8). Due to the flat trajectory of
the 5.56 round, this will allow the central crosshair to be used effectively
form 0–200 yards.
Note: If you are using
the center crosshair at
200 yards, maximum
accuracy will be
obtained by holding
3-inches (1.5 MOA)
high on the desired
target.
The three horizontal
lines below the central
crosshair will then
provide 300, 400 and
500 holdover references.
100-200 Yards
300 Yards
400 Yards
500 Yards
EBR-556B Reticle Holdover References
4. Fire a final three-shot group to confirm proper adjustment. Repeat
as necessary.
8
9
Reticle Subtensions
Ranging
The EBR-556B reticle incorporates a simple ranging design. By matching
an object of 15 inches in width (example, the shoulder width on a
silhouette target) to the crossbar images, the approximate range can be
determined.
15 Inches
18.85
.5
4.4
8
12.5
35
.5
200 Yards / 15 Inches
300 Yards /15 Inches
400 Yards / 15 Inches
500 Yards / 15 Inches
1.5
Ranging Crossbars
200 Yards
300 Yards
400 Yards
500 Yards
Subtensions are measured in MOA.
10
11
7.6 MOA
5 MOA
4 MOA
3 MOA
Accessory Options
Troubleshooting
The 3x Spitfire includes two Picatinny rails for mounting accessories
such as lights, lasers and red dot sights.
Please check the following before returning a scope for service:
If the reticle does not illuminate:
• Is the battery dead? Replace.
Picatinny Rails.
If desired, rails can be
removed.
• Is the battery installed correctly? Be sure the battery is oriented
with plus sign facing upward.
• Is the battery cover loose? Be sure cover is snug and contact points
are clean.
If bullets are not grouping:
Be sure the crossbolt nut is tight. You should not be able to twist or
move the Spitfire in any direction. Many times, problems thought to be
with the scope are actually mount problems.
Note: For any issues not listed above, please view our online
Troubleshooting Guide:
» www.vortexoptics.com/content/troubleshooting
12
13
Maintenance
The VIP Warranty
Cleaning
We build optics based on our commitment to your absolute satisfaction.
That’s why Vortex products are unconditionally guaranteed and we make
this Very Important Promise to you—a Very Important Person.
The Vortex Spitfire prism scope requires very little routine maintenance
other than to periodically clean the exterior lenses. The exterior of the
scope may be cleaned by wiping with a soft, dry cloth.
When cleaning the lenses, be sure to use products that are specifically
designed for use on coated optical lenses such as the Vortex Lens Pen
and FogFree Cleaning Kits.
• Be sure to blow away any dust or grit on the lenses prior to wiping
the surfaces.
• Using your breath, or a very small amount of water or pure alcohol,
can help remove stubborn things like dried water spots.
Lubrication
All components are permanently lubricated, so no additional lubricant
should be applied.
Note: Do not attempt to disassemble any components of the scope.
Storage
Rest assured that in the event your Spitfire becomes damaged or
defective, Vortex Optics will repair or
replace the red dot at no charge to you.
Call Vortex Optics at 800-426-0048 for
prompt, professional, and friendly service.
Vortex Optics
2120 West Greenview Drive
Unlimited
Unconditional
Middleton, WI 53562
Lifetime Warranty
[email protected]
Visit www.vortexoptics.com for more information. Canadian customers may
visit www.vortexcanada.net for customer service information.
Note: The VIP warranty does not cover theft, loss, or deliberate damage to
the product.
Keep lens covers closed to protect the lenses when not in use.
• Remove the battery when putting in storage for extended periods.
• Avoid storage in direct sunlight or in any very hot location.
• Storage and use in extreme cold will shorten battery life.
14
15