Download Datasheet - CREATIVE CHIPS GmbH

Survey
yes no Was this document useful for you?
   Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Document related concepts

Phase-locked loop wikipedia , lookup

Spark-gap transmitter wikipedia , lookup

Transistor–transistor logic wikipedia , lookup

Ohm's law wikipedia , lookup

Immunity-aware programming wikipedia , lookup

Superheterodyne receiver wikipedia , lookup

Operational amplifier wikipedia , lookup

TRIAC wikipedia , lookup

Regenerative circuit wikipedia , lookup

Power MOSFET wikipedia , lookup

Current source wikipedia , lookup

Power electronics wikipedia , lookup

Integrated circuit wikipedia , lookup

Electrical ballast wikipedia , lookup

Radio transmitter design wikipedia , lookup

Surge protector wikipedia , lookup

Resistive opto-isolator wikipedia , lookup

Wien bridge oscillator wikipedia , lookup

Current mirror wikipedia , lookup

Switched-mode power supply wikipedia , lookup

Index of electronics articles wikipedia , lookup

Valve RF amplifier wikipedia , lookup

Charlieplexing wikipedia , lookup

Network analysis (electrical circuits) wikipedia , lookup

RLC circuit wikipedia , lookup

Opto-isolator wikipedia , lookup

Rectiverter wikipedia , lookup

Transcript
CCA4100 – Flasher/Oscillator
LED FLASHER CCA4100
FEATURES





LED flashlight driver IC
Long operation time with one 1.5V battery cell
Low number of external components (one capacitor)
Large operating range from 1 to 5V
Average current drain less than 500µA
(over battery life cycle)
 Wide temperature range
 Low cost
 Fully function compatible to LM3909
Application Circuit
300µ / 3 V
1
Pin Configuration (SOP 8)
F-RC
1
8
S-RC
OUT
2
7
NC
NC
3
6
RL
GND
4
5
Vcc
Chip Layout
8
2
7
CCA
4100
3
6
4
5
1,5 V
Flash rate: ~ 1 Hz
CCA
4100
GENERAL DESCRIPTION
The CCA4100 is an insensitive and easy to use IC to flash Light Emitting Diodes (LEDs). For operating it only needs an external capacitor and a standard 1.5V
battery cell. The circuite is self starting and includes internal timing resistors and a resistor to limit LED current. The device is optimised for minimal power drain at
1.5V and 3V at nominal flashing rates. Typical Applications are toys, advertising gimmicks or novelties but also applications with necessity to locate something in
the dark as fishing floats, fire alarms and fire extinguishers or emergency switches and exits. The circuit could also be used for electronic applications as triggers
and saw tooth generators.
ELECTRICAL CHARACTERISTICS
Conditions:
Parameter
-40 oC < TOP < 85 oC;
Symbol Conditions
Supply voltages
VCC, VDD
Flash Frequency
f
High Flash Frequency
fh
Current
I
Peak LED current
ILEDmax
Pulse Width
TPW
C = 300 µF (5%)
C = 0.30 µF (5%)
in operation mode
C = 350 µF
C = 350 µF at half
amplitude
Min.
1.1
0.65
Typ.
1.0
1.1
0.55
45
6.0
Max.
Unit
6.0
1.3
V
Hz
kHz
mA
mA
ms
0.75
PIN NAME DESCRIPTION
1
2
3
4
5
6
7
8
F-RC
Out
NC
GND
VCC
RL
NC
S-RC
Fast Frequency
Voltage Output to charge capacitor
no connected
ground
supply voltage
current limited resistor out
no connected
Slow Frequency
Disclaimers:
Creative Chips GmbH reserves the right to make changes without further notice to any
products herein to improve reliability, function or design. Creative Chips does not
assume any liability arising out of the application or use of any product or circuit
described herein; neither does it convey any license under its patent rights, nor the
rights of others. These products are not authorized for use as critical components in life
support devices or systems without the express written approval of Creative Chips.
39/2013
CREATIVE CHIPS GmbH, Im Bubenstück 1, 55411 Bingen am Rhein, GERMANY
Web: www.creativechips.com || Email: [email protected] || Tel.: +49 (0) 67 21 / 9 87 22 - 0