Download simple plan for a multi frequency zapper

Multi Frequency Wart+ Zapper
15-Feb-2012
Use an in stock power suppy, maybe 12 VDC (~15 V actual).
Input~15V. Ouptput3~13.5V
(For Experimental use only. Use at your own risk, and not near mercury amalgam fillings!)
+15.2v DC input
Ouput to Cu pipe ~12V.
DC Power Jack Suggestion-->
18V maximum
Make it easy to change transformers (and input voltage).
Assemble circuit on strip board. Use drill bit w/ handle to cut tracks.
.01 uF or 0.1 uF bypass capacitor
Optional 10 uF tantalum in parallel with R3 to stabilize output.
R1 Group
3.9M
(ZAP time)
High
1-4 DIP switches
Single Pole ST
100K 56K
22K
4.7K
http://www.taydaelectronics.com/dc-power-jack-2-1mm-barrel-type-pcb-mount.html
Or, replace the
R1 group of
resistors with a
single 56K
resistor for
~2500 Hz.
Wart Zapper Circuit ~Currents
3.9 K
+15.2v
1,000 ohms
555
+12.2V
up to 200 mA
Temporarily jump a 10 uF
here to drop down to 3Hz
(R1=56K) to visually verify
the 555 timer is working. If
not, check your solder job
and circuit!
470 ohms
0.033 amps
wet skin @12V
100,000 ohms
122 micro amps
R2 discharge
LED maximum
R1 K
Output + 3,900.0
(Cu or SS Pipe)
97.5
Common Setting
0.01 uF
.01 uF
short leg is neg on LED & Cap
Buy an 8 pin DIP IC Socket Adaptor Solder Type
so that you don’t solder the 555 (heat sensitive) chip.
Hook an alligator clip to the ground. Use a dull Stainless Steel sewing
O
needle to kill (small) warts/moles in ~5 minutes. The negative lead
u
works best. Experiment on output pipe and needle location. Moles,
t
underarms, and Candida are good conductors (very fast kill) while thick
skinned hands & feet are not (slower results). Pain means it is dying.
p
Or, use a copper pipe covered with a damp cloth instead of a needle.
u
You can kill several at one time by covering both with a pipe. The
t
speed with which this kills warts suggests it might also kill many
_
other things, which could be good or bad for you.
WARNING: This is a very powerful zapper. Start out very slowly. You
don't have to guess if this zapper is working when you see warts die.
For lower power, use a 6 or 9 VDC transformer or thicker skin. Read
about Clark zappers on the web BEFORE experimenting.
555 Chip:
http://www.taydaelectronics.com/8-pin-dip-ic-socket-adaptor-solder-type.html
Dip Switch
Output Shorted
dry skin
+13.5V R3= 470 ohm
(Off Time, Low)
Other Zapper Plans: http://zappers.narod.ru/
http://www.taydaelectronics.com/dip-switch-4-positions-gold-plated-contacts-top-actuated.html
How to solder: http://www.youtube.com/watch?v=I_NU2ruzyc4
Best zapper?:
Wart zapper:
0.44 watts
Use Wet Cloth!
1,000,000 ohms 12 micro amps
1,000 ohms
0.015 amps
0.23 watts
3,900 ohms
0.004 amps
0.06 watts
Turn ON Frequency Duty Cycle
none
37 Hz
100%
1
1,450 Hz
99%
2
2,522 Hz
98%
1,2
3,840 Hz
97%
3
6,042 Hz
96%
1,3
7,232 Hz
95%
2,3
8,136 Hz
94%
55.2
35.6
21.9
17.9
15.7
1-3
4
1,4
2,4
1,2,4
3,4
1,3,4
2-4
1-4
13.6
4.7
4.5
4.3
4.2
3.9
3.7
3.6
3.5
9,252 Hz
21,551 Hz
22,251 Hz
22,787 Hz
23,453 Hz
24,582 Hz
25,201 Hz
25,676 Hz
26,267 Hz
94%
85%
85%
84%
84%
83%
83%
82%
82%
http://www.taydaelectronics.com/ne555-ic-555-sgs-thomson-timer.html
http://zap.intergate.ca/how.htm
http://www.zen22142.zen.co.uk/Circuits/Misc/wart_zap/wart_zapper.htm
StripBoard:
http://www.taydaelectronics.com/hardware/prototyping-boards/small-stripboard-94x53mm-copper.html
Strip Board Layout
http://www.kpsec.freeuk.com/stripbd.htm