* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Download Sepam - HV/MV Protection and control units (ENG)
Brushed DC electric motor wikipedia , lookup
Electric power system wikipedia , lookup
Power inverter wikipedia , lookup
Electrification wikipedia , lookup
Thermal runaway wikipedia , lookup
Pulse-width modulation wikipedia , lookup
Mercury-arc valve wikipedia , lookup
Immunity-aware programming wikipedia , lookup
Electrical ballast wikipedia , lookup
Stepper motor wikipedia , lookup
Power engineering wikipedia , lookup
Current source wikipedia , lookup
Voltage regulator wikipedia , lookup
Ground (electricity) wikipedia , lookup
Variable-frequency drive wikipedia , lookup
Control system wikipedia , lookup
Electrical substation wikipedia , lookup
Resistive opto-isolator wikipedia , lookup
History of electric power transmission wikipedia , lookup
Stray voltage wikipedia , lookup
Buck converter wikipedia , lookup
Power electronics wikipedia , lookup
Voltage optimisation wikipedia , lookup
Distribution management system wikipedia , lookup
Three-phase electric power wikipedia , lookup
Protective relay wikipedia , lookup
Switched-mode power supply wikipedia , lookup
Electrical wiring in the United Kingdom wikipedia , lookup
Surge protector wikipedia , lookup
Mains electricity wikipedia , lookup
Alternating current wikipedia , lookup
Protection and control Catalogue June 2001 Sepam 1000+ Merlin Gerin Substation Transformer Motor Busbar Get more with the world’s Power & Control specialist Contents Schneider Electric Presentation 2 More solutions Flexible architecture User-machine interface 2 5 6 Selection table 8 Sepam 1000+ series 20 Sepam 1000+ series 40 8 9 Metering 10 Description Characteristics 10 11 Protection function 12 Description Setting ranges 12 14 Connection schemes 16 Sepam 1000+ series 20 Sepam 1000+ series 40 Other connection schemes 16 17 18 Control and monitoring 20 Description 20 Logic inputs and outputs 21 Description Assignment by application Sepam 1000+ series 20 Assignment by application Sepam 1000+ series 40 21 22 23 Optional remote modules 24 Description Connections 24 25 Sensors 26 Core balance CTs Interfaces 26 27 Communication 28 Description and characteristics 28 Parameters and protection settings 30 Description Program logic 30 31 Characteristics 32 Size and weight Electrical characteristics Environmental characteristics 32 34 35 1 Presentation More solutions The Sepam 1000+ family of protection and metering units is designed for the operation of machines and electrical distribution networks of industrial installations and utility substations for all levels of voltage. It consists of complete, simple and reliable solutions, suited to the following applications: # protection of substations (incomers and feeders) # protection of transformers # protection of motors # protection of busbars. Sepam 1000+ series 20 Suitable for common applications, Sepam 1000+ series 20 offers simple solutions based on current or voltage metering. The Sepam 1000+ series 20 S20, T20 and M20 current units cover applications such as the following: # protection of substation incomers and feeders against phase-to-phase and phase-to-earth short-circuits 16 IDMT tripping curves adjustable timer hold to detect recurrent faults switching of groups of setting to adapt to changes in the network configuration protection of overhead lines with reclosers protection of transformers against overloads, with ambient temperaturecompensated RMS thermal overload protection with 2 groups of settings for different ventilation operating rates # protection of motors 5 against overloads, with ambient temperature-compensated RMS thermal overload protection with a cold tripping curve that can be adjusted to fit motor characteristics 5 against internal faults and load-related faults 5 with motor starting condition monitoring and machine operation assistance. 5 5 5 # # The Sepam 1000+ series 20 B21 and B22 voltage units are suitable for the following situations: # monitoring of network voltage and frequency # loss of mains detection by rate of change of frequency protection for installations with local power generation. Sepam 1000+ series 40 Sepam 1000+ series 40, with its current and voltage metering capabilities, offers high-performing solutions for more demanding applications. Sepam 1000+ series 40 units perform the following functions in addition to those performed by Sepam 1000+ series 20: # protection of networks with parallel incomers by directional protection # directional earth fault protection suitable for all earthing systems, impedant, isolated or compensated neutral # all the necessary electrical measurements: phase and residual current, phase-toneutral, phase-to-phase and residual voltage, frequency, power and energy, … # comprehensive network diagnosis assistance: 20 seconds of disturbance recording, detailed history of the last 200 alarms, storage of contexts of the last 5 trips # adaptation of control functions by a logical equation editor # customization of alarm messages to fit each application, and/or in the user's language. Sepam 1000+ selection guide Selection criteria Measurements Specific protection functions Series 20 I Applications Substation Transformer Motor Busbar S20 T20 M20 U Series 40 U Loss of mains (ROCOF) I and U I and U Directional earth fault I and U Directional earth fault and phase overcurrent S40 T40 S41 S42 T42 M41 B21 B22 Example : For motor protection and current and voltage measurements, your solution is the M41 type Sepam 1000+. 2 Schneider Electric Presentation More solutions More simplicity Simple to install # no constraints for integration in cubicles due to the compact size of the base units and remote installation of optional modules # universal auxiliary power supply. Simple to commission # all the functions are ready to use # user-friendly, powerful PC setting software to utilize all the possibilities offered by Sepam 1000+. Simple to operate With the advanced UMI, all local operations are made easier by a clear, complete presentation of all the required information in your language. Simple to maintain # digital unit self-diagnosis and watchdog # switchgear diagnosis assistance functions to assess equipment condition and schedule preventive maintenance operations: 5 cumulative breaking current 5 breaking device operating and charging time. More communication Modbus communication All the data needed for centralized management of your electrical network are available with the communication option based on the open, international Modbus protocol: # measurement and diagnosis values # remote indication and time-tagging of events # remote control of the installation # remote setting of protection functions # reading of disturbance recording files. Ethernet connection and Webserver Sepam 1000+ can be connected to an Ethernet broadband network by Ethernet/ Modbus communication gateways. With these gateways : # Sepam 1000+ can be integrated in any automation and supervisory system based on Modbus / TCP/IP multi-master protocol # Web pages presenting information provided by Sepam may be consulted via an Internet/Intranet browser. PowerLogic System Sepam 1000+ is a component of PowerLogic System and may naturally be associated with SMS centralized industrial and commercial electrical network management software. Schneider Electric 3 Presentation More solutions More modularity Sepam 1000+ is available with 2 User Machine Interface (UMI) levels: # advanced UMI, with keypad and graphic LCD display 5 to provide all the data required for local operation of the installation: measurements, diagnosis information, alarms, etc. 5 to set Sepam 1000+ parameters and protection functions 5 to be understood by all, the screens can be displayed in the user’s language. The advanced UMI may be part of the base unit or installed as a remote unit in the most convenient location for the user. # basic UMI, with signal lamps 5 no need for local operation 5 for remotely operated installations. In order to adapt to as many situations as possible and allow for subsequent upgrading of the installation, Sepam 1000+ may be functionally enhanced at any time by the addition of optional modules: # logic input/output module with parameterizable program logic # communication module # temperature sensor module # analog output module. 4 Schneider Electric Presentation Flexible architecture E54735 (1) MES108 module 4 logic outputs, 4 logic inputs or MES114(1) 4 logic outputs, 10 logic inputs ACE949-2 (2-wire) module ACE959 (4-wire) module communication network interface (1) Sepam 1000+ base unit with advanced UMI Trip Io 0o 51 I>> on 51n Io> n >51 Io> n ff t ex CCA612 MW r 2.1 = 0 Kva A P 90 V = .3 M Q 2 = S et res CCA772 (2) r lea c MSA141 module (1) 1 analog output 1 I>5 ERIN NG RLI MepEam s CCA783 (2) CCA770 MET148 module(1) 8 temperature sensors SFT 2841 parameter setting and operating software SFT 2826 disturbance recording restoring software (1) optional additional module. (2) example, the prefabricated cords come in 3 different lengths. Schneider Electric 5 E54928 Presentation User-machine interface Sepam 1000+ has two levels of UMI (user-machine interface) suited to every operating requirement. Basic UMI on I>51 I>>51 Io>51N Io>>51N ext 0 off I on This UMI includes: # 2 signal lamps indicating Sepam 1000+ operating status: 5 green "on" indicator: device on 5 red "wrench" indicator: device unavailable (initialization phase or detection of an internal failure) # 9 parameterizable yellow signal lamps equipped with a standard label (1) # "reset" button for clearing faults and resetting # 1 connection port for the RS232 link with the PC, the port is protected by a sliding cover. This UMI offers a low-cost solution for installations that do no require local operation (run from a remote monitoring and control system) or to replace electromechanical or analog electronic protection devices without any additional operating requirements. Trip reset Example of basic UMI with standard signal lamp assignment. I>51 I>>51 Io>51N Io>>51N 0 off ext I on Advanced UMI trip E54929 on 1 I1 = 162A I2 = 161A I3 = 163A 2 3 9 8 7 6 clear reset 5 4 Example of advanced UMI with standard signal lamp assignment. In addition to the basic UMI functions, this version provides: # a "graphic" LCD display with automatic contrast adjustment and user-triggered backlighting. It is used to display measurements, parameter/protection settings and alarm and operating messages. Number of lines, size of characters and symbols according to screens and language versions. # a 9-key keypad with two operating modes: White keys for current operation: ➀ display of measurements. ➁ display of switchgear and network diagnosis data. ➂ display of alarm messages. ➃ resetting. ➄ acknowledgment and clearing of alarms. Blue keys for parameter setting and protection setting: ➆ access to protection settings. ➇ access to Sepam 1000+ parameter settings (2). ➈ used to enter the 2 passwords required to change protection and parameter settings. The “ ↵, ▲, ▼ ” keys (➃, ➄, ➅) are used to navigate in the menus and to scroll and accept the values displayed. ➅ "lamp test" keys: switching on sequence of all the signal lamps. This UMI is an optimum solution for local operation facilitated by clear legibility, content and access to the different data items. Remote advanced UMI The advanced UMI functions are also available in a remote module that is connected to a Sepam 1000+ with a basic UMI (connection by prefabricated cable of different lengths).. The module is installed on the front panel of the cubicle in the most appropriate operating location. (1) this removable label may be replaced by a customized label produced using the SFT 2841 software tool. (2) for parameter setting of the program logic, the expert UMI must be used. 6 Schneider Electric Presentation User-machine interface Expert UMI This UMI is available as a complement to the standard or advanced UMI on the screen of a PC equipped with the SFT 2841 software tool and connected to the RS 232 link on the front panel of the Sepam (operating in a Windows > V95 or NT environment). All the data used for the same task are grouped together in the same screen to facilitate operation. Menus and icons are used for fast, direct access to the required information. Sepam 1000+ series 20: measurements. Current operation # display of all metering and operating data # display of alarm messages with the time of appearance # display of diagnosis data such as: 5 tripping current 5 number of switchgear operations and cumulative breaking current # display of all protection and parameter settings # display of the logic status of inputs, outputs and signal lamps. This UMI is the solution suited to occasional local operation for demanding personnel who require fast access to all the information. Parameter setting – protection setting (1) # display and setting of all the parameters of each protection function in the same page # program logic parameter setting, parameter setting of general installation and Sepam data # input data may be prepared ahead of time and transferred into the corresponding Sepam 1000+ series 20: setting of protection function 50/51. Sepam units in a single operation (downloading function). Main functions performed by SFT 2841 : # changing of passwords # entry of general settings (ratings, integration period, …) # entry of protection settings # changing of program logic assignments # enabling/disabling of functions # saving of files. Saving # protection and parameter setting data may be saved # printing of reports is possible as well. This UMI may also be used to recover disturbance recording files and provide graphic display using the SFT 2826 software tool. Operating assistance Access from all the screens to a help section which contains all the technical data required for Sepam installation and use. (1) modes available via 2 passwords (protection setting level, parameter setting level). Schneider Electric 7 Selection table Functions Sepam 1000+ series 20 Type of Sepam Substation S20 4 4 Transformer Protection ANSI code T20 Phase overcurrent 50/51 4 Earth fault, sensitive earth fault 50N/51N 4 Breaker failure 50BF Negative sequence / unbalance 46 1 1 Directional phase overcurrent 67 Directional earth fault 67N/67NC Active overpower 32P Thermal overload 49RMS 2 Phase undercurrent 37 Locked rotor, excessive starting time 48/51LR Starts per hour 66 Positive sequence undervoltage 27D/47 Remanent undervoltage 27R Phase-to-phase undervoltage 27 Phase-to-neutral undervoltage 27S Phase-to-phase overvoltage 59 Neutral voltage displacement 59N Negative sequence overvoltage 47 Overfrequency 81H Underfrequency 81L Rate of change of frequency 81R Recloser (4 cycles) 79 5 Thermostat / Buchholz 5 Temperature monitoring (with MET148, 2 set points per sensor) 38/49T 8 Metering Phase current I1, I2, I3 RMS, Residual current Io # # Average current I1, I2, I3, Peak demand phase currents # # Voltage U21, U32, U13, V1, V2, V3, Residual voltage Vo Positive sequence voltage Vd / rotation direction Negative sequence voltage Vi Frequency Active and reactive power P and Q, Peak demand P and Q, Power factor Active and reactive energy (Wh, VARh) Temperature measurement 5 Network and machine diagnosis Tripping current I1, I2, I3, Io # # Tripping context Unbalance ratio / negative sequence current Ii # # Phase angle ϕo, ϕ1, ϕ2, ϕ3 Disturbance recording # # Thermal capacity used # Remaining operating time before overload tripping # Waiting time after overload tripping # Running hours counter / operating time # Starting current and time Start inhibit time delay, number of starts before inhibition Switchgear diagnosis Cumulative breaking current # # Trip circuit supervision 5 5 Number of operations, Operating time, Charging time 5 5 CT / VT supervision Control and monitoring Circuit breaker / contactor control (2) 5 5 Logic discrimination 5 5 Switching of setting groups #(3) #(3) Program logic parameter setting (Boolean equation editor: AND, OR, …) Additional modules 8 temperature sensor outputs - MET148 module 5 1 low level analog output - MSA141 module 5 5 Logic inputs and ouputs - MES108 module (4I/4O) or MES114 (10I/4O) 5 5 RS485 interface - ACE 949-2 (2-wire) or ACE959 (4-wire) module 5 5 #standard, 5 according to parameter setting and MES108, MES114 or MET148 input/output module options Motor M20 4 4 Busbar B21 (5) B22 2 1 2 1 2 2 2 1 2 1 2 2 1 2 1 2 1 # # # # # # # # 5 5 5 5 5 5 5 5 1 2 1 1 1 8 # # 5 # # # # # # # # # # 5 5 5 5 #(3) 5 5 5 5 (1) available in 2002. (2) for shunt trip unit or undervoltage release coil. (3) exclusive choice between logic discrimination and switching from one 2-relay group of settings to another 2-relay group. (4) 2 modules possible. (5) performs B20 type functions. 8 Schneider Electric Selection table Functions Sepam 1000+ series 40 Type of Sepam Substation S40 S41 4 4 4 4 1 (1) 1 (1) 2 2 Protection Code ANSI Phase overcurrent 50/51 Earth fault, sensitive earth fault 50N/51N Breaker failure 50BF Negative sequence / unbalance 46 Directional phase overcurrent 67 Directional earth fault 67N/67NC 2 Active overpower 32P 1 (1) Thermal overload 49RMS Phase undercurrent 37 Locked rotor, excessive starting time 48/51LR Starts per hour 66 Positive sequence undervoltage 27D/47 Remanent undervoltage 27R Phase-to-phase undervoltage 27(6) 2 2 Phase-to-neutral undervoltage 27S(6) 2 2 2 2 Phase-to-phase overvoltage 59(6) Neutral voltage displacement 59N 2 2 Negative sequence overvoltage 47 1 1 Overfrequency 81H 2 2 Underfrequency 81L 4 4 Rate of change of frequency 81R Recloser (4 cycles) 79 5 5 Thermostat / Buchholz Temperature monitoring (with MET148, 2 set points per sensor) 38/49T Metering Phase current I1, I2, I3 RMS, Residual current Io # # Average current I1, I2, I3, Peak demand phase currents # # Voltage U21, U32, U13, V1, V2, V3, Residual voltage Vo # # Positive sequence voltage Vd / rotation direction # # Negative sequence voltage Vi # # Frequency # # Active and reactive power P and Q, Peak demand P and Q, Power factor # # Active and reactive energy (Wh, VARh) # # Temperature measurement Network and machine diagnosis Tripping current I1, I2, I3, Io # # Tripping context # # Unbalance ratio / negative sequence current Ii # # Phase angle ϕo, ϕ1, ϕ2, ϕ3 # # Disturbance recording # # Thermal capacity used Remaining operating time before overload tripping Waiting time after overload tripping Running hours counter / operating time Starting current and time Start inhibit time delay, number of starts before inhibition Switchgear diagnosis Cumulative breaking current # # Trip circuit supervision 5 5 Number of operations, Operating time, Charging time 5 5 CT / VT supervision #(1) #(1) Control and monitoring Circuit breaker / contactor control (2) # # Logic discrimination 5 5 Switching of setting groups # # Program logic parameter setting (Boolean equation editor: AND, OR, …) #(1) #(1) Additional modules 8 temperature sensor outputs - MET148 module 1 low level analog output - MSA141 module 5(1) 5(1) Logic inputs and ouputs - MES108 module (4I/4O) or MES114 (10I/4O) 5 5 RS485 interface - ACE 949-2 (2-wire) or ACE959 (4-wire) module 5 5 # standard, 5according to parameter setting and MES108, MES114 or MET148 input/output module options (1) available in 2002. (2) for shunt trip unit or undervoltage release coil. (3) exclusive choice between logic discrimination and switching from one 2-relay group of settings to another 2-relay group. (4) 2 modules possibles. (5) performs B20 type functions. (6) exclusive choice, phase-to-neutral or phase-to-phase voltage for each of the 2 relays. Schneider Electric S42 (1) 4 4 1 2 2 2 1 Transformer T40 (1) T42 (1) 4 4 4 4 1 1 2 2 2 2 Motor M41 (1) 4 4 1 2 2 1 2 1 1 1 2 1 2 2 2 2 1 2 4 2 2 2 2 2 2 1 2 4 2 2 2 2 1 2 4 5 8/16 5 8/16 8/16 # # # # # # # # # # # # # # # # 5 # # # # # # # # 5 # # # # # # # # 5 # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # 5 5 # # 5 5 # # 5 5 # # 5 5 # # 5 # # # 5 # # # 5 # # # 5 # # 5 5 5 5(4) 5 5 5 5(4) 5 5 5 5(4) 5 5 5 2 2 2 2 1 2 4 5 9 Metering Description Metering fonctions Distrubance recording Recording of sampled values of analog measurement signals and logic states. Through parameter setting, it is possible to choose: # the events that will trigger a record # the recording time prior to the occurrence of the event # the number and duration of records (series 40 only). The values are displayed as primary values with the related units: A,V,Hz,°C,°F, W, … Current # RMS current for each of the 3 phases in the circuit, taking into account harmonics up to number 17 # residual current. Average current and peak demand current # average current on each of the 3 phases # greatest average current on each of the 3 phases (peak demand current). The peak demand currents give the current consumed at the time of peak loads. The average current is calculated over a period that may be parameterized from 5 to 60 mn, and may be reset to zero. Voltage phase-to-neutral voltages V1, V2, V3 phase-to-phase voltages U21, U32, U13 positive sequence voltage Vd residual voltage Vo negative sequence voltage Vi. # # # # # Frequency Power Active, reactive and apparent power, power factor (p.f.). Peak demand power Greatest value of active and reactive power absorbed, over the same period as peak demand currents, with the possibility of resetting to zero. Energy Active and reactive energy. A counter for each current flow direction. Temperature Measurement of the temperature of each sensor. Network diagnosis assistance functions Tripping current Storage of the 3 phase currents and earth current at the time Sepam gave the last tripping order, so as to find the fault current (fault analysis). The values are stored until the next trip order is given. Tripping context Storage of the tripping currents and the Io, U21, U32, U13, Vo, Vi, Vd, F, P, Q, values at the time of the detection of the fault. The values for the last five trips are stored. Negative sequence / unbalance Ratio of negative sequence phase current, characteristic of unbalanced power supply of the equipment to be protected. Series 20 Series 40 Number of records in COMTRADE format Total duration of a record Characteristics 2 Adjustable from 1 to 10 86 periods (1.72 s at 50 Hz , 1.43 s at 60 Hz) Number of points per cycle 12 Adjustable from 1 s to 10 s The total of all the records plus one must not be more than 20 s at 50 Hz and 16 s at 60 Hz 12 Duration of recording before the Adjustable from 0 to 85 occurrence of the event periods Recorded data Currents or voltages, logic inputs, pick-up Adjustable from 0 to 99 periods Currents and voltages, logic inputs, pick-up, logic outputs (O1 to O4) Machine operation assistance functions Thermal capacity used Temperature build-up related to the load. It is displayed as a percentage of the nominal machine temperature. Remaining operating time before overload tripping Indicates the time remaining before tripping by the thermal overload protection function. Waiting time after overload tripping Indicates the time remaining before starting is allowed according to inhibition by the thermal protection function. Starting current and time / motor overload Measurement of the maximum current consumed by the motor during a starting sequence or an overload, as well as the duration. Start inhibit time delay / number of starts before inhibition Indicates the remaining number of starts allowed by the starts per hour protection function and, if the number is zero, the waiting time before starting is allowed. Running hours counter / operating time Cumulative time during which the protected equipment (motor or transformer) is on load (I > 0.1 Ib). The cumulative value is displayed in hours (0 to 65535 h). Switchgear diagnosis assistance functions These measurements are to be compared with the data supplied by the switchgear manufacturer. Cumulative breaking current The value displayed may be used to evaluate the state of the circuit breaker poles. Number of operations Total number of opening operations performed by the device. Device operating time Operating time, charging time. These data may be used to evaluate the state of the pole operating mechanism. Phase angles # phase angle ϕ1, ϕ2, ϕ3 between phase currents l1, l2, l3 and voltages U32, U13, U21 respectively # phaseangle ϕo between residual current and residual voltage. 10 Schneider Electric Characteristics Metering General settings (set in the general settings menu) Frequency 50 Hz or 60 Hz Current sensor CT 1 A or 5 A rated current In (1) LPCT rated current In (1) Residual current Io sensor CSH120/CSH200 rated current Ino Core balance CT + ACE990 rated current Ino (1) 1 A or 5 A CT + CSH30 rated current Ino (1) 1 A ou 5 A CT + CSH30 sensitivity x10 courant nominal Ino (1) Voltage sensor Primary rated voltage Unp (2) VT 100, 110, 115, 120 V (Uns) VT 200, 230 V Series 20 and Series 40 number (l1, l2, l3) or (l1, l3) 1 A to 6250 A number (l1, l2, l3) 25 A to 3150 A 2 A, 20 A 5A 1 A to 6250 A 1 A to 6250 A (Ino = In) 1 A to 6250 A (Ino = In/10) 220 V à 250 kV V1, V2, V3 U21, U32 U21 V1, V2, V3 Metering functions Ranges Accuracy series 20 (7) Phase current 0.1 to 1.5 In (1) ± 1 % typically Residual current 0.1 to 1.5 Ino (1) ± 1 % typically Peak demand current (9) 0.1 to 1.5 In (1) ± 1 % typically Phase-to-phase voltages 0.05 to 1.2 Unp (2) ± 1 % typically Phase-to-neutral voltages 0.05 to 1.2 Vnp (2) ± 1 % typically Positive sequence voltage 0.05 to 1.5 Vnp (2) ±2% Negative sequence voltage 0.05 to 1.5 Vnp (2) Residual voltage 0.015 to 3 Vnp (2) ± 1 % typically Frequency 50/60 Hz ± 5 Hz ± 0.05 Hz typically Active power 1.5 % Sn (8) at 999 MW Reactive power 1.5 % Sn (8) at 999 Mvar Apparent power 1.5 % Sn (8) at 999 MVA Power factor -1 to 1 (CAP / IND) Peak demand active power (9) 1.5 % Sn (8) at 999 MW Peak demand reactive power (9) 1.5 % Sn (8) at 999 Mvar 0 to 2.1 108 MW.h Active energy (9) Reactive energy (9) 0 to 2.1 108 Mvar.h Temperature -30 to +200 °C (6) ± 1 °C Tripping current (9) phase 0.1 to 40 In (1) ±5% earth 0.1 to 20 Ino (1) ±5% Neg. sequence / unbalance 10 % to 500 % Ib (5) ±2% 0 to 359° Phase angle ϕ1, ϕ2, ϕ3 Phase angle ϕo 0 to 359° Thermal capacity used (9) 0 to 800 % (4) Operating time (9) 20 to 100 ms ± 1 ms typically Charging time (9) 1 to 20 s ± 0.5 s Running hours counter 0 to 65535 h ± 1 % + 0.5 h ± 0.5 % MSA141 measurement converter 4-20 mA or 0-20 mA or 0-10 mA (1) In, Ino: CT primary rated current. (2) Unp: primary rated phase-to-phase voltage, Vnp: primary phase-to-neutral voltage Vnp=(Unp/√3). (3) measurements available in analog format according to parameter setting and MSA141 module. (4) 100 % is the thermal capacity used of the equipment being protected under its rated load: I = Ib. (5) Ib basis current of the equipment being protected. (6) displayed in °C or °F according to parameter setting, typical accuracy from + 20 °C à + 140 °C. (7) in reference conditions (IEC 60255-4), typically at In or Un or Sn. (8) Sn: apparent power, Sn =√3.In.Un. (9) Saved in the event of power outage. Schneider Electric Series 40 only Accuracy series 40 (7) ± 0.5 % typically ± 1 % typically ± 0.5 % typically ± 1 % typically ± 1 % typically ±2% ±2% ±5% ± 0.02 Hz typically ± 1 % typically ± 1 % typically ± 1 % typically ± 1 % typically ± 1 % typically ± 1 % typically ± 1 %, ± 1 digit ± 1 %, ± 1 digit ± 1 °C ±5% ±5% ±2% ± 2° typically ± 2° typically ± 1 ms typically ± 0.5 s ± 1 % + 0.5 h ± 0.5 % MSA141 (3) # # # # # # # # # # 11 Protection functions Description Current protection functions Directional earth fault (ANSI 67N/67NC) It has 2 types of characteristics: # type 1, according to Io protection # type 2, according to Io magnitude. It can operate on impedant, isolated or compensated neutral grounding systems. The type 1 units allow the detection of restriking faults. The protection includes two units: # definite time (DT) # IDMT (16 types of IDMT curves) (type 2 only) # instantaneous or time-delayed. The type 2 units have a reset time setting that allows: # detection of restriking faults # coordination with electromechanical relays. Phase overcurrent (ANSI 50/51) Three-phase protection against overloads and phaseto-phase short-circuits. The protection comprises four units: # definite time (DT) # IDMT (16 types of IDMT curves) # instantaneous or time-delayed. Each unit has a reset time setting that allows: # detection of restriking faults # coordination with electromechanical relays. Earth fault (ANSI 50N/51N or 50G/51G) Earth fault protection. Earth faults may be detected according to parameter setting by: # current transformers on the three phases (3I sum) # a special core balance CT, CSH120 or CSH200, according to the required diameter; this method provides the highest sensitivity. The choice of parameterizable ratings provides a very wide setting range. # a current transformer (1 A or 5 A), combined with a CSH30 interposing ring CT. The protection comprises four units: # definite time (DT) # IDMT (16 types of IDMT curves) # instantaneous or time-delayed. Each unit has a reset time setting that allows: # detection of restriking faults # coordination with electromechanical relays. It also has a harmonic 2 restraint in order to ensure stability upon transformer energizing. Breaker failure (ANSI 50 BF) Backup protection that delivers a tripping order to the upstream or adjacent breakers should the breaker that is being commanded fail to trip, detected by measurement of the phase current after a tripping order. Negative sequence / unbalance (ANSI 46) Protection against phase unbalance. Sensitive protection to detect 2-phase faults at the end of long feeders. Protection of equipment against temperature build-up caused by an unbalanced supply or the inversion or loss of a phase and against phase current unbalance. IDMT or definite time characteristics. Directional current protection functions Directional phase overcurrent (ANSI 67) This protection function is 3-phase. It comprises a phase overcurrent function associated with direction detection. It picks up if the phase overcurrent function in the chosen direction (line or busbar) is activated for at least one of the three phases. It operates as definite time or IDMT. It is insensitive to the loss of measurement voltage at the time of the fault. 12 Power protection functions Active overpower (ANSI 32P) This protection function is activated if the active power flowing in one direction or the other according to the application (supplied or absorbed) is greater than the set point. Machine protection functions Thermal overload (ANSI 49) Protection of equipment against thermal damage caused by overloads. The thermal capacity used is calculated according to a mathematical model which takes into account: # RMS current values # ambient temperature. The function comprises: # an adjustable alarm setting # an adjustable trip setting 5 transformer application. The model takes into account the transformer heat rise and cooling time constants according to whether natural or forced ventilation is used (ONAN, ONAF) via a logic input. 5 motor application. The model takes into account: - two time constants: the heat rise time constant, used when the motor is running, and the cooling time constant, used when the motor is stopped, - effect of negative sequence current on rotor heating. An additional setting may be used to adapt the protection to the motor thermal withstand indicated by the experimental hot and cold curves given by the machine manufacturer. The thermal protection function may be inhibited by a logic input when this is required by the process running conditions. Phase undercurrent (ANSI 37) Protection of pumps against the consequences of a loss of priming. The protection function detects time-delayed current drops that correspond to motor no-load operation, characteristic of the loss of pump priming. Locked rotor / excessive starting time (ANSI 48/51LR) Protection of motors that are liable to start with overloads or insufficient supply voltage and/or that drive loads that are liable to jam (e.g. crushers). The locked rotor function is an overcurrent protection function that is only confirmed after a time delay that corresponds to the normal starting time. Starts per hour (ANSI 66) Protection against overheating caused by too frequent starts. Checking of the number of: # starts per hour (or adjustable time period) # consecutive starts. The protection inhibits motor energizing for a preset time period when the permissible limits have been reached. Motor restarting may be taken into account by a logic input. Schneider Electric Protection functions Description Thermostat, Buchholz, gas, pressure, temperature detection Protection of transformers against temperature rise and internal faults via logic inputs linked to devices integrated in the equipment. Temperature monitoring (RTDs) (ANSI 38/49T) Protection against abnormal overheating of motor windings and/or bearings equipped with RTDs. The protection includes 2 independent set points that are adjustable for each RTD. Positive sequence undervoltage (ANSI 27D) (ANSI 47) Motor protection against malfunctioning due to insufficient or unbalanced supply voltage. Detection of reverse rotation direction. In order for this protection to be used, voltage transformers must be connected to Sepam 1000+ to measure U21 and U32. Remanent undervoltage (ANSI 27R) Monitoring of the clearing of voltage sustained by rotating machines after circuit opening. The protection is used to prevent transient electrical and mechanical phenomena that are caused by fast re-energizing of motors. It monitors phase-to-phase voltage U21 or phase-to-neutral voltage V1. Voltage protection functions Phase-to-phase undervoltage (ANSI 27) Protection used either for automated functions (transfer, load shedding) or to protect motors against undervoltage. The protection function monitors the drop in each of the phase-to-phase voltages being metered. Phase-to-neutral undervoltage (ANSI 27S) Protection used to detect phase-to-earth faults (isolated neutral systems). Phase-to-phase overvoltage (ANSI 59) Protection against abnormally high voltage or checking that there is sufficient voltage for power supply changeover. It operates with phase-to-phase voltage (series 20 and series 40) or with phase-to-neutral voltage (series 40 only). Neutral voltage displacement (ANSI 59N) Detection of insulation faults in isolated neutral systems by measurement of neutral voltage displacement. The protection function is generally associated with transformer incomer or busbar protection. The function includes 2 set points. Negative sequence overvoltage (ANSI 47) Protection against phase unbalance resulting from distant faults, a phase inversion or unbalanced power supply. Frequency protection functions Overfrequency (ANSI 81H) Protection against abnormally high frequency. Underfrequency (ANSI 81L) Detection of variances with respect to the rated frequency, in order to maintain a high quality power supply. The protection may be used for overall tripping or for load shedding. Rate of change of frequency / R. O. C. O. F (ANSI 81R) Protection used for fast disconnection of a source transmitting power into a power network when a fault occurs or to monitor load shedding. Recloser Automation device used to reclose the circuit breaker after tripping triggered by a transient fault on a line (the function includes 4 parameterizable reclosing cycles). Schneider Electric 13 Protection functions Setting ranges General settings (set in the general settings menu) Frequency 50 Hz or 60 Hz Current sensor CT 1 A or 5 A rated current In LPCT rated current In (3) Residual current Io sensor CSH120/CSH200 rated current Ino Core balance CT (2) + ACE990 rated current Ino TC 1 A or 5 A + CSH30 rated current Ino TC 1 A or 5 A + CSH30 sensitivity x10 (4) rated current Ino Voltage sensor Primary rated voltage Unp VT : 100, 110, 115, 120 V (Uns) Functions Phase overcurrent Tripping curve Is set point Reset time Confirmation (4) VT : 200, 230 V Settings Definite time SIT, LTI, VIT, EIT, UIT (1) RI CEI: SIT/A, LTI/B, VIT/B, EIT/C IEEE: MI (D), VI (E), EI (F) IAC: I, VI, EI 0.1 to 24 In 0.1 to 2,4 In Definite time (DT: timer hold) IDMT (IDMT: reset time) None By negative sequence overvoltage By phase-to-phase undervoltage Earth fault Tripping curve Iso set point Reset time Breaker failure Presence of current Operating time Negative sequence / unbalance Definite time IDMT Tripping curve Definite time SIT, LTI, VIT, EIT, UIT (1) RI CEI: SIT/A,LTI/B, VIT/B, EIT/C IEEE: MI (D), VI (E), EI (F) IAC: I, VI, EI 0.1 to 15 Ino 0.1 to 1 Ino Definite time (DT: timer hold) IDMT (IDMT: reset time) Reset time Characteristic angle 14 2 A, 20 A or 5 A (4) 1 A to 6250 A 1 A to 6250 A 1 A to 6250 A (Ino = In/10) 220 V to 250 kV V1, V2, V3 U21, U32 U21 V1, V2, V3 Time delays Reset time DT DT DT DT or IDMT DT or IDMT DT or IDMT Definite time IDMT Reset time DT DT DT DT or IDMT DT or IDMT DT or IDMT Definite time IDMT Inst.: 0.05 s to 300 s 0.1 s à 12.5 s to 10 Is Inst.: 0.05 s to 300 s 0.5 s to 300 s Inst.: 0.05 s to 300 s 0.1 s to 12.5 s at 10 Iso Inst.: 0.05 s to 300 s 0.5 s to 300 s 0.2 to 2 In 0.05 s to 30 s 0.1 to 5 Ib 0.1 to 0.5 Ib (Schneider Electric) 0.1 to 1Ib (CEI, IEEE) Schneider Electric CEI: SIT/A, LTI/B, VIT/B, EIT/C (4) IEEE: MI (D), VI (E), EI (F) (4) Directional phase overcurrent Tripping curve Is set point Number (I1, I2, I3) or (I1, I3) 1 A to 6250 A Number (I1, I2, I3) 25 A to 3150 A Definite time SIT, LTI, VIT, EIT, UIT (1) RI CEI: SIT/A, LTI/B, VIT/B, EIT/C IEEE: MI (D), VI (E), EI (F) IA: I, VI, EI 0.1 to 24 In 0.1 to 2,4 In Definite time (DT: timer hold) IDMT (IDMT: reset time) 30°, 45°, 60° Reset time DT DT DT DT or IDMT DT or IDMT DT or IDMT Definite time IDMT 0.1 s to 300 s 0.1 s to 1 s Inst.: 0.05 s to 300 s 0.1 s to 12.5 s at 10 Is Inst.: 0.05 s to 300 s 0.5 s to 300 s Schneider Electric Protection functions Setting ranges Functions Settings Directional earth fault, according to Io projection (type 1) Characteristic angle -45°, 0°, 15°, 30°, 45°, 60°, 90° Iso set point 0,1 to 15 Ino Vso set point 2 to 80 % of Un Memory time Tomem duration Vomem validity set point Directional earth fault, according to Io magnitude (type 2) Characteristic angle -45°, 0°, 15°, 30°, 45°, 60°, 90° Tripping curve Definite time SIT, LTI, VIT, EIT, UIT (1) RI CEI, SIT/A,LTI/B, VIT/B, EIT/C IEEE: MI (D), VI (E), EI (F) IAC: I, VI, EI Iso set point 0.1 to 15 Ino 0.1 to 1 Ino Vso set point 2 to 80 % of Un Reset time Definite time (DT: timer hold) IDMT (IDMT: reset time) Active overpower 1 to 120 % of Sn Thermal overload Negative sequence factor Time constant Heat rise Cooling Alarm and trip set points Cold curve change factor Rate change condition Maximum equipment temperature Phase undercurrent Time delay Definite time Inst.: 0.05 s to 300 s 0; 0.05 s to 300 s 0; 2 to 80 % of Un Reset time DT DT DT DT or IDMT DT or IDMT DT or IDMT Definite time IDMT Inst.: 0.05 s to 300 s 0.1 s to 12.5 s at 10 Iso Inst.: 0.05 s to 300 s 0.5 s to 300 s Rate 1 Rate 2 0 - 2.25 - 4.5 - 9 T1: 5 to 120 mn T2: 5 to 600 mn 50 to 300 % of rated thermal capacity used 0 to 100 % by logic input by Is setting from 0.25 to 8 Ib 60 to 200 °C 0.15 to 1 Ib T1: 5 to 120 mn T2: 5 to 600 mn 0.05 s to 300 s Excessive starting time/locked rotor Starts per hour Starts per period Consecutive starts Temperature (RTDs) Alarm and trip set points Positive sequence undervoltage 0.5 Ib to 5 Ib ST start time LT and LTS time delays 0.5 s to 300 s 0.05 s to 300 s 1 to 60 1 to 60 Period time between starts 1 to 6 h 0 to 90 mn 0 to 180 °C (or 32 to 356 °F) 15 to 60 % de Unp 0.05 s to 300 s 5 to 100 % of Unp 0.05 s to 300 s 5 to 100 % of Unp, 5 to 100 % of Vnp (4) 0.05 s to 300 s Remanent undervoltage Phase-to-phase undervoltage Phase-to-neutral undervoltage Overvoltage 5 to 100 % of Vnp phase-to-phase 50 to 150 % of Unp 0.05 s to 300 s phase-to-neutral (4) 50 to 150 % of Vnp 0.05 s to 300 s Neutral voltage displacement 2 to 80 % of Unp 0.05 s to 300 s 1 to 50 % of Unp Inst.: 0.05 s to 300 s 50 to 53 Hz or 60 to 63 Hz 0.1 s to 300 s 45 to 50 Hz or 55 to 60 Hz 0.1 s to 300 s 0.1 to 10 Hz/s Inst.: 0.15 s to 300 s Negative sequence overvoltage Overfrequency Underfrequency Rate of change of frequency Reminder: In current, Unp rated voltage and Ino current are general settings that are made at the time of Sepam commissioning. They are given as the values on the measurement transformer primary windings. In is the current sensor rated current (CT rating) (adjustable from 1 A to 6250 A). Unp is the rated phase-to-phase voltage of the voltage sensor primary windings (adjustable from 220 V to 250 kV). Ino is the core balance CT current rating. Ib is the current which corresponds to the equipment power rating, adjustable from 0.4 to 1.3 In. The current, voltage and frequency values are set by direct entry of the values (resolution: 1 A, 1 V, 1 Hz, 1°C or F). (1) tripping as of 1.2 Is. (2) with ACE 990 interface for core balance CT with ratio n of 50 to 1500 turns. (3) table of In values in Amps: 25, 50, 100, 125, 133, 200, 250, 320, 400, 500, 630, 666, 1000, 1600, 2000, 3150. (4) on series 40 only. Schneider Electric 15 Sepam 1000+ series 20 Connection schemes Connection to 1 A / 5 A current sensors Connector A A Type Screw-on Ring lug 6.35 mm Ring lug 4 mm RJ45 RJ45 B C D Ref. CCA620 L1 E79273 S20 / T20 / M20 types L2 L3 Cable 1 wire 0.2 to 2.5 mm2 (4 AWG 24-12) 2 wires 0.2 to 1 mm2 (4 AWG 24-16) A CCA622 CCA630 1.5 to 6 mm2 (AWG 16 to AWG 10) CCA612 CCA770: L = 0,6 m CCA772: L = 2 m CCA774: L = 4 m 4 1 O1 5 4 O2 8 7 11 O3 B 5 2 10 15 14 13 O4 6 3 1 2 A 17 18 +/~ –/~ 19 to communication network interface C communication D B21 / B22 types Connector A Type Screw-on Ref. CCA620 A Ring lug 6.35 mm Screw-on CCA622 B C D RJ45 RJ45 CCT640 to optional modules L1 Cable 1 wire 0.2 to 2.5 mm2 (4 AWG 24-12) 2 wires 0.2 to 1 mm2 (4 AWG 24-16) 1 wire 0.2 to 2.5 mm2 (4 AWG 24-12) 2 wires 0.2 to 1 mm2 (4 AWG 24-16) CCA612 CCA770: L = 0,6 m CCA772: L = 2 m CCA774: L = 4 m L2 L3 B (1) A 1 2 3 4 5 6 7 8 O1 5 4 O2 8 7 O3 11 10 15 14 13 O4 1 2 17 C communication D +/~ –/~ to communication network interface to optional modules (1) this type of connection allows the calculation of residual voltage. 16 Schneider Electric Sepam 1000+ series 40 Connection schemes L1 E79225 S40 / S41 / S42 types T40 / T42 / M41 types L2 L3 Connection to 1 A / 5 A current sensors Connector A A Type Screw-on Ref. CCA620 CCA622 C D Ring lug 6.35 mm Ring lug 4 mm RJ45 RJ45 E Screw-on CCA626 B E Ring lug 6.35 mm CCA630 CCA627 (1) Cable 1 wire 0.2 to 2.5 mm2 (4 AWG 24-12) 2 wires 0.2 to 1 mm2 (4 AWG 24-16) 1.5 to 6 mm2 (AWG 16 to AWG 10) CCA612 CCA770: L = 0,6 m CCA772: L = 2 m CCA774: L = 4 m 1 wire 0.2 to 2.5 mm2 (4 AWG 24-12) 2 wires 0.2 to 1 mm2 (4 AWG 24-16) E A 1 2 3 (2) O1 5 4 O2 8 7 O3 11 10 5 6 4 1 B 5 2 15 14 13 O4 6 3 1 2 17 A 18 +/~ –/~ 19 C communication D to communication network interface to optional modules (1) this type of connection allows the calculation of residual voltage. (2) accessory for bridging of terminals 3 and 5 supplied with CCA626 connector. Schneider Electric 17 Other connection schemes Connection schemes Connection of two 1 A / 5 A current transformers with CCA630 connector. L1 L2 L3 E79275 Phase current 4 1 B 5 2 6 3 CCA630 L1 L2 L3 E79276 Connection of 3 LPCT type current transformers with CCA670 connector (the sensors are equipped with a standard connection cable: L = 5 m). L1 B L2 L3 # connection of CSH30 interposing ring CTs to 1 A: current transformers: make 2 turns through the CSH primary winding # connection of CSH30 interposing ring CTs to 5 A: current transformers: make 4 turns through the CSH primary winding # with series 40, the sensitivity can be multiplied by 10 by parameter setting with the CSH30 interposing ring CT: Ino = In/10. E79272 Residual current E79277 CCA670 1 A CT or 5 A CT 1 A CT: 2 turns 5 A CT: 4 turns Connection of the ACE990 interface to the core balance CT with ratio 1/n with 50 6 n 6 1500 (n = number of turns on the core balance CT secondary winding). E79278 1 A CT: 2 turns 5 A CT: 4 turns L1 / L2 / L3 A S1 18 n turns E1 En 18 ACE 990 S2 19 Schneider Electric Other connection schemes Phase voltage (series 20) L1 L1 L2 L2 L3 L3 # connection of 1 voltage transformer (does not allow E79280 Connection schemes use of positive sequence undervoltage or neutral voltage displacement protection functions) # connection of 2 voltage transformers in V arrangement (does not allow use of neutral voltage displacement protection function) # connection of VTs to CCT640 connector. 1 2 3 4 5 6 7 8 # measurement of phase voltages with 1, 2 or 3 VTs B 1 2 3 4 5 6 7 8 L1 E79281 Residual voltage (series 20) B and measurement of residual voltage by VT in open delta connection # connection of VTs to CCT640 connector. L2 L3 B # connection of 1 voltage transformer (does not allow L1 L1 L2 L2 use of phase-to-phase or directional protection functions) # connection of 2 voltage transformers in V arrangement (does not allow use of neutral voltage displacement or directional earth fault protection functions) # connection of VTs directly to connector E on the base unit. L3 Residual voltage (series 40) L1 measurement of residual voltage by VT in open delta connection # connection of VTs directly to connector E on the base unit. 1 2 3 5 6 E79230 # measurement of phase voltages with 1 or 2 VTs and E79229 Phase voltage (series 40) E79228 1 2 3 4 5 6 7 8 E L3 1 2 3 5 6 L2 L3 1 2 3 5 6 Schneider Electric E E 19 Control and monitoring Description Sepam 1000+ performs the basic control and monitoring functions necessary for the operation of the electrical network, thereby reducing the need for auxiliary relays. The control and monitoring functions may be parameterized using the SFT 2841 software tool, however each type of Sepam has parameter setting by default which allows easier commissioning in the most frequent cases of use. Latching / acknowledgment (ANSI 86) Output relay latching may be parameterized. Latched tripping orders are stored and must be acknowledged in order for the device to be put back into service. The user acknowledges via the keypad or remotely via a logic input or the communication link. Latching is stored in the event of a power outage. Two control modes are available # integrated circuit breaker control. This logical function processes all the circuit breaker closing and tripping conditions based on position information, external control orders and protection, recloser, etc. # individual parameter setting of output relays. Control of output relays according to an assignment matrix. Breaking device control # Sepam is used to control breaking devices equipped with different types of closing and tripping coils: 5 circuit breakers with shunt trip or undervoltage trip units (parameter setting on front panel (1) or via SFT 2841) 5 latching contactors with shunt-trip units. Output relay control (standard or fail-safe) may be parameterized. By default, the program logic is adapted to control a circuit breaker with a shunt trip unit. # open and close control via the communication link # inhibition of closing (ANSI 69) Sepam inhibits the closing of the circuit breaker or contactor according to the operating conditions. # remote tripping Remote control of the tripping of the circuit breaker or contactor is possible via a logic input or via the communication link. # inhibition of remote control A logic input inhibits the remote closing of the circuit breaker via the communication link. Switching of setting groups Used to switch from one group of (directionnal) phase overcurrent and earth fault protection settings to another group of settings. Switching may be performed by a logic input or via the communication link. Inhibition of thermal protection Thermal protection tripping may be inhibited via a logic input. Re-acceleration Allows a logic input to take into account the restarting of an unstopped motor. Logic discrimination (ANSI 68) This function allows quick, selective tripping of the definite time or IDMT phase overcurrent and earth fault protection relays, without requiring the use of time intervals between upstream and downstream protection devices. The downstream relay transmits a blocking input signal if the protection device set points are exceeded. The upstream relay receives the blocking input signal on the logic input used for the inhibition function. A saving mechanism ensures the operation of the protection in the event of an inhibition link failure. Annunciation (ANSI 30) Sepam indicates the appearance of alarms by: # signal lamps on the front panel # messages on the display. The addressing of the signal lamps may be parameterized. The sequence is as follows (advanced UMI): # when an event appears, the signal lamp goes on and the related message is displayed # the user presses the “clear” key to erase the message # after the fault disappears and the “reset”, key is pressed, the signal lamp goes off and/or the message is erased and the protection is reset # the list of alarm messages remains accessible ( key) and may be erased by pressing the “clear” key. Remote annunciation Used to transfer information via the communication link. Information such as circuit breaker position, SF6 fault alarm, etc. Trip circuit supervision Detects trip circuit faults (shunt trip units). Detects open/closed position discrepancy faults (undervoltage trip units). Watchdog Indicates Sepam unavailability via output O4. Output relay testing This function is used to activate each output relay (1). Logical parameter setting (Boolean equation editor) Used for logical grouping of protection function outputs and logic inputs by the AND, OR, NO functions in order to supply new states that can activate a logic output, a signal lamp, an alarm message or a remote indication. List of main messages (1) Functions Phase overcurrent Earth fault Directional phase overcurrent Directional earth fault Active overpower Thermal overload Negative sequence / unbalance Locked rotor Excessive starting time Starts per hour Undercurrent Overvoltage Undervoltage Positive sequence undervoltage Neutral voltage displacement Negative sequence overvoltage Overfrequency Underfrequency Temperature (RTDs) Thermostat (3) Buchholz (3) Recloser Recloser Breaker failure Messages (2) PHASE FAULT (4) EARTH FAULT DIR. PHASE FAULT (4) DIR. EARTH FAULT REVERSE P THERMAL TRIP THERMAL ALARM. UNBALANCE I ROTOR BLOCKING LONG START START INHIBIT UNDER CURRENT OVERVOLTAGE (4) UNDERVOLTAGE (4) UNDERVOLTAGE.PS Vo FAULT UNBALANCE V OVER FREQ. UNDER FREQ. OVER TEMP.ALM THERMOST. ALARM BUCHHOLZ ALARM FINAL TRIP CLEARED FAULT BREAKER FAILURE (1) according to type of Sepam and Sepam equipped with advanced UMI, or SFT 2841. (2) messages by default, the wording of the messages may be changed (please consult us). (3) or gas, pressure, temperature detector (DGPT). (4) indication of the faulty phase with series 40. 20 Schneider Electric Description 4 output relays on the base unit E79423 E79422 Logic inputs and ouputs CSH 19 18 17 19 18 17 15 14 13 15 14 13 O4 11 10 O3 8 7 O2 5 4 O1 2 -/a 1 +/a O4 11 10 O3 8 7 O2 5 4 O1 O3 and O4 are indication outputs, only O4 can be activated by the watchdog function. 2-/a 1 +/a CCA622 connector (terminal block for ring terminals). Optionnal input / output modules E79425 CCA620 connector (screw-on terminal block for straight fittings). E79424 The 4 relay outputs O1, O2, O3 and O4 on the base unit are connected to connector A . Connector A of the base unit may be either of the following: # CCA620 screw type connector # CCA622 ring lug connector. O1 and O2 are 2 control outputs used by the breaking device control function for: # O1: breaking device tripping # O2: inhibition of breaking device closing. CSH 12 11 O14 12 11 O14 9 8 O13 9 8 O13 6 5 O12 6 5 O12 3 2 O11 3 2 O11 L By the addition of an input/output extension module, the 4 outputs on the base unit may be completed by either of the following: # 4 inputs and 4 outputs with the MES108 module # 10 inputs and 4 outputs with the MES114 module. An MES module is mounted at the back of the base unit. Output characteristics # 4 relay outputs O11, O12, O13, O14 5 O11: control output, used for breaking device closing 5 O12, O13, O14: indication outputs. L Input characteristics 11 10 I14 11 10 I13 8 7 5 4 I12 5 4 I12 2 1 I11 2 1 I11 I21 8 7 M O1 4 M 2 4 5 Wiring for shunt trip coil. With monitoring of trip circuit and open / closed matching. Schneider Electric 2 1 K Wiring of the breaking device trip circuit 5 O1 4 M 1 I11 I12 Connection to screw-type connector # 1 wire with cross-section 0.2 à 2.5 mm² (4 AWG 24-12) # or 2 wires with cross-section 0.2 à 1 mm² (4 AWG 24-16). A + _ E79427 E79426 5 8 7 6 5 4 MES114 module (10 inputs / 4 outputs). D A 10 9 I14 I26 I25 I24 I13 I23 I22 M MES108 module (4 inputs / 4 outputs). # 4 or 10 potential-free inputs 5 DC input voltage of 24 V DC to 250 V DC, external DC supply source. + _ D Wiring to be used when the "breaker control" function is activated. 1 I11 I12 2 4 5 Wiring for undervoltage release coil. With monitoring of open / closed matching. 21 Logic inputs and ouputs Assignment by application Sepam 1000+ series 20 Chart of input assignments by application (series 20) The use of the preset control and monitoring functions requires exclusive parameter setting and particular wiring of the inputs according to their application and the type of Sepam. The choice is made on the advanced UMI or expert UMI. Functions Logic inputs Open position S20 T20 M20 B21 - B22 Assignment # # # # # # # # # # # # # # # # (2) # # (3) # # # # I11 External tripping 3 (1) Buchholz alarm (1) (Buchholz alarm message) Rotor rotation detection # # (4) # End of charging position Thermostat alarm (1) (thermostat alarm message) # Inhibit remote control (1) SF6-1 # # # # # # # # # # Closed position Logic discrimination, receive BL Switching of groups of settings A/B External reset External tripping 4 (1) External tripping 1 (1) External network synchronization External tripping 2 (1) Motor reacceleration SF6-2 Change of thermal settings Inhibit thermal overload Inhibit recloser Logic outputs Tripping Inhibit closing Watchdog Closing order # # # # # # # # # I12 I13 # # # # # # # # # # # # # I14 # I23 # # I21 I22 I24 # # # # # # # # I25 # # # # # # # # O1 I26 O2 O4 O11 Nota : all of the logic inputs are available via the communication link and are accessible in the SFT 2841 control matrix for other non predefined applications. (1) these inputs have parameter setting with the prefix "NEG" for undervoltage type operation. (2) Buchholz/Gas trip message. (3) thermostat trip message. (4) pressure trip message. 22 Schneider Electric Logic inputs and ouputs Assignment by application Sepam 1000+ series 40 Chart of input assignments by application (series 40) The functions defined in the chart below are associated with a logic input by configuration. This means that the functions used may be adapted to suit needs within the limits of the logic inputs available. They may be reversed for undervoltage type operation. Functions Logic inputs Open position Closed position Logic discrimination, receive BL Switching of groups of settings A/B External reset External tripping 1 External tripping 2 External tripping 3 S40, S41, S42 # # # # # # # # Buchholz/gas tripping Thermostat tripping Pressure tripping Buchholz/gas alarm Thermostat alarm Pressure alarm End of charging position Inhibit remote control SF6 Inhibit recloser External network synchronization # # # # # Inhibit thermal overload Change of thermal settings T40, T42 # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # # Rotor rotation detection Inhibit undercurrent protection Open order Close order Logic outputs Tripping Inhibit closing Watchdog Closing control order Assignment I11 I12 Free # # # # # I13 Free Free Free Free Free Free Free Free Free Free # # # Free Free Free Free Motor reacceleration Inhibit closing M41 # # # # # # # # # # # # # # # # # # I21 Free Free Free Free Free Free Free Free O1 O2 O4 O11 Nota : all of the logic inputs are available via the communication link and are accessible in the SFT 2841 control matrix for other non predefined applications. Schneider Electric 23 Optional remote modules Description E79428 Remote advanced UMI modules The DSM303 modules provides the functional features of the fixed advanced UMI. Associated with a Sepam 1000+ with a basic UMI, it may be installed on the front panel of the cubicle in the most appropriate operating location. # reduced depth of 30 mm # a single module for each Sepam 1000+ with basic UMI, to be connected by one of the prefabricated cords CCA772 or CCA774 (2 or 4 meters). This module may not be connected to a Sepam 1000+ that has an integrated advanced UMI. Trip f 0 of 1 I>>5 on 1n Io>5 51n Io>> I on t ex 2A 16 = 61A 1 I1 = 63A 1 I2 = I3 rese t ar cle Remote advanced UMI module. E79429 Analog output module ✞✕✑ ✐ ✐ ✐ ✐ ✐ ✐ ✐ ✐ ✐ ✐ ✐ ✐✐ ✎✎ ✎✐ I✐ ✐ The MSA141 module converts one of the Sepam 1000+ measurements into an analog signal. # selection of the measurement to be converted by parameter setting # analog signal 0-10 mA, 4-20 mA, 0-20 mA according to parameter setting # connection of the analog output to the screw-type connector: 5 1 wire with cross-section 0.2 à 2.5 mm² (4 AWG 24-12) 5 or 2 wires with cross-section 0.2 à 1 mm² (4 AWG 24-16) # a single module for each Sepam 1000+ base unit, to be connected by one of the prefabricated cords CCA770, CCA772 or CCA774 (0.6 or 2 or 4 meters). Analog output module. E79430 Temperature sensor module Temperature measurement (e.g. in transformer or motor windings) is utilized by the following protection functions: # thermal overload (to take into account the ambient temperature) # temperature monitoring. With the MET148 module, 8 temperature sensors may be connected. # type of temperature sensor Pt100, Ni100 or Ni120 according to parameter setting # 3-wire temperature sensors # connection of temperature sensors to screw-type connectors: 5 1 wire with cross-section 0.2 à 2.5 mm² (4 AWG 24-12) 5 or 2 wires with cross-section 0.2 à 1 mm² (4 AWG 24-16) # a single module for each Sepam 1000+ series 20 base unit, to be connected by one of the prefabricated cords CCA770, CCA772 ou CCA774 (0.6 ou 2 ou 4 mètres) # 2 modules for each Sepam 1000+ series 40 base unit, to be connected by one of the prefabricated cords CCA770, CCA772 ou CCA774 (0.6 ou 2 ou 4 mètres). Temperature sensor module. 24 Schneider Electric Optional remote modules Connections Connection of DSM303 Remote advanced UMI Wiring inter-modules links Different module connection combinations are possible and the modules are connected by prefabricated cords which come in 3 different lengths. # CCA770 (L = 0.6 m) # CCA772 (L = 2 m) # CCA774 (L = 4 m). The modules are linked by the cords which provide the power supply and act as functional links with the Sepam unit ( D connector to Da connector, Dd to Da , ...). The DSM303 module may only be connected at the end of the link. E79432 DSM303 Da Connection of MSA141 Remote analog output Sepam 1000+ CCA772 E79433 MSA141 E79435 A 1 2 Da D 3 MSA141 module Dd Da M ERLIN GERIN Rc + A Dd CCA772 (or CCA774) RIN GE N RIN RLI G E M paEmR10LI00N MsepaEm 1000 CCA770 se A D1 Dd Da E79434 Connection of MET148 8 temperature sensor inputs A 1 2 3 n˚1 MET148 MET148 module B 1 2 3 4 n°5 5 6 7 Maximum configuration Three modules at the most may be connected to the base unit in accordance with the order and maximum lengths of connections specified in the chart below: 4 5 6 n°2 DSM303 remote UMI B n°6 Base Cable Module 1 Cable Module 2 Cable Module 3 CCA772 CCA772 CCA772 CCA772 MSA141 MSA141 MSA141 MET148 CCA770 CCA770 CCA770 CCA770 MET148 MET148 MET148 MET148 CCA774 CCA774 CCA772 CCA774 DSM303 DSM303 MET148 DSM303 7 8 9 n°4 10 11 12 8 9 n°7 10 11 12 n°8 MERLIN GERIN n°3 Da LIN0 GERIN 100 MER am LIN 0 MER sep 100 am sep Series 20 Series 40 Series 40 Series 40 Dd Schneider Electric 25 Core balance CTs CSH120, CSH200 core balance CTs E40466 E40465 Sensors Mounted directly on cable. The specially designed CSH 120 and CSH 200 core balance CTs are used for direct residual current measurement. The only difference between them is the diameter. Characteristics: # inner diameter and weight: 5 CSH120 : ø 120 mm ; 0.6 kg 5 CSH200 : ø 200 mm ; 1.4 kg # accuracy: ± 5 % at 20 °C # transformer ratio: 1/470 # maximum permissible current: 20 kA - 1 s # operating temperature: -25 °C to +70 °C # storage temperature: -40 °C to +85 °C # drift in accuracy related to temperature: ± 1 % # the wiring resistance should be < 4 Ω. Mounted on plate or rail. Dimensions E54926 D 4 horizontal mounting holes dia. 5 F øA H B K 4 vertical mounting holes dia. 5 J L E Dimensions (mm) A B CSH120 120 164 CSH200 200 256 26 D E F H J K L 44 190 76 40 166 62 35 46 274 120 60 257 104 37 Schneider Electric Interfaces CSH30 E40468 Horizontal CSH30 mounting. The CSH 30 interposing ring CT is used as an interface when the residual current is measured using 1 A or 5 A current transformers. It should be installed near the Sepam input (max. distance 2 m). # weight: 0.12 kg # mounted on symmetrical DIN rail. Vertical CSH30 mounting. E54925 E44717 Sensors Dimensions 60 29 8 4 50 ø 30 82 16 5 2 ø 4,5 2 ø 4,5 058758RC ACE990 The ACE990 interface is used to adapt measurements between a MV core balance CT with a ratio of 1/n (50 6 n 6 1500), and the residual current input of the Sepam 1000+. Characteristics weight: 0.64 kg mounted on symmetrical DIN rail accuracy: amplitude: ± 1 % phase: < 2° maximum permissible current: 20 kA 1 s (an the primary winding of a MV core balance CT with a ratio of 1/50 that does not saturate) # operating temperature: -5 °C +55 °C. # storage temperature: -25 °C +70 °C. # # # 5 5 # Dimensions 1 ACE 990 Schneider Electric 27 Communication Description and characteristics :LWK0RGEXVFRPPXQLFDWLRQ6HSDP XQLWVPD\EHFRQQHFWHGWRDUHPRWH PRQLWRULQJDQGFRQWUROV\VWHPHTXLSSHG ZLWKDPDVWHU0RGEXVFRPPXQLFDWLRQ FKDQQHOZLWKDQ56W\SHSK\VLFDOOLQNRU ZLWKDQRWKHUOLQNHTXLSSHGZLWKDQ DSSURSULDWHFRQYHUWHU. 7RFRQQHFW6HSDPXQLWVWRDQ 56 QHWZRUNDQLQWHUIDFHPRGXOHLV UHTXLUHG: # ACE949-2 LQWHUIDFHIRUZLUH56 QHWZRUN # ACE959 LQWHUIDFHIRUZLUH56 QHWZRUN. Data available The data available depend on the type of Sepam. All of the data used by the remote monitoring and control system are grouped together so as to be available in a single readout. Readout of measurements and diagnosis information All the values measured by Sepam 1000+ are available from the control station: # phase and earth fault currents, peak demand currents # phase-to-phase, phase-to-neutral and residual voltages, frequency # active and reactive power, peak demand power, energy counters # temperatures # switchgear diagnosis information: cumulative breaking current, operating time and number of operations, circuit breaker recharging time, etc. # machine operating assistance information: motor starting time, remaining operating time before overload tripping, waiting time after tripping, etc. Remote indications # reading of digital remote indication information. E79436 Remote indications are preassigned to the protection or control functions and depend on the type of Sepam. # reading of the status of 10 logic inputs. Remote control orders Writing of 16 impulse type remote control orders (TC): # in direct mode # or in SBO (Select Before Operate) mode). The remote control orders are preassigned to the metering, protection or control functions and depend on the type of Sepam. Time-tagging of events # time-tagged information: logic inputs, remote indications # time-tagging of events within a ms # synchronization by Modbus network or by external signal on logic input I21. Remote reading ACE949-2, interface for 2-wire RS 485 network. # reading of Sepam configuration and identification # reading of protection settings (remote reading) # writing of protection settings (remote setting). E79437 Protection setting writing may be inhibited by parameter setting. Other functions available via the communication link # remote control of the MSA141 optional analog output # transfer of disturbance recording data. Characteristics Type of transmission Protocol Rate Data format Response time ACE959, interface for 4-wire RS 485 network. Maximum number of Sepam 1000+ on a Modbus network RS 485 electrical interface Electrical interface power supply Type of connection Maximum length of RS 485 network with standard cable (lengths multiplied by 3 with FILECA, with a maximum of 1300m) Asynchronous serial Modbus slave (Jbus profile) 4800, 9600, 19200, 38400 bauds 1 start, 8 bits, no parity, 1 stop 1 start, 8 bits, even parity, 1 stop 1 start, 8 bits, odd parité, 1 stop Less than 15 ms 25 ACE949-2, complies with EIA standard 2-wire RS 485 differential ACE959, complies with EIA standard 4-wire RS 485 differential External, by 12 V DC ou 24 V DC auxiliary supply Screw terminals and tightening yokes for shielding connection With 12 V DC distributed power supply to interfaces 320 m with 5 Sepam 1000+ 180 m with 10 Sepam 1000+ 160 m with 20 Sepam 1000+ 125 m with 25 Sepam 1000+ With 24 V DC distributed power supply to interfaces 1000 m with 5 Sepam 1000+ 750 m with 10 Sepam 1000+ 450 m with 20 Sepam 1000+ 375 m with 25 Sepam 1000+ 28 Schneider Electric E79288 Communication Description and characteristics Connection of the ACE949-2 Interface for 2-wire RS 485 network Implementation of the Modbus network A RS 485 network A set of adapted accessories is used for fast, dependable implementation of the communication network from both the electrical and environmental (electromagnetic compatibility) viewpoints. ACE 949-2 E79287 V+ VL+ L- 1 2 B 3 MERLIN GERIN LL+ VV+ CCA612 to Sepam C RS 485 network MERLIN GERIN 4 MERLIN GERIN ➀ Network connection interface, to be supplied by 12 V DC or 24 V DC distributed power supply # ACE949-2 for 2-wire RS 485 network # or ACE959 for 4-wire RS 485 network. ➁ CCA612 cord for connection of the connection interface to the C port of the Sepam base unit. ➂ Interface for connection of the RS 485 network to the Modbus master, with distributed power supply to the ACE949-2 or ACE959 interfaces and polarization/ termination of the communication link # ACE909-2, RS 485 / RS 232 converter # or ACE919CA (110 V AC or 220 V AC) RS 485/RS485 interface # or ACE919CC (24 V DC or 48 V DC) RS 485/RS 485 interface. Connection of the ACE959 Interface for 4-wire RS 485 network E79289 ACE959 (1) A ➃ Modbus network cable VV+ Rx+ RxTx+ Tx- (1) VV+ Rx+ RxTx+ Tx- # for 2-wire RS 485 network: two shielded twisted pairs (1 RS 485 pair, 1 pair for power supply) # for 4-wire RS 485 network: three shielded twisted pairs (2 RS 485 pairs, 1 pair for power supply) with tinned copper braiding shielding, coverage: > 65 % characteristic impedance: 120 Ω gauge: AWG 24 resistance per unit length: < 100 Ω per km capacitance between conductors: < 60 pF per m capacitance between conductor and shielding: < 100 pF per m maximum length: 1300 m. B CCA612 C to Sepam # # # # # # # Example of standard cable (for 2-wire RS 485 network): # supplier: BELDEN reference: 9842 # supplier: FILOTEX reference: FMA-2PS. High performance cable (for 2-wire RS 485 network): # supplier: FILECA reference : F2644-1 (cable distributed by Schneider Electric in VV+ D (2) 60 m strand, reference CCR301). For more information, refer to the "Sepam – RS 485 network connection guide" PCRED399074EN. Rx+, Rx-: Sepam receiving (eq IN+, IN-) Tx+, Tx-: Sepam transmitting (eq OUT+, OUT-) (1) distributed power supply with separate wiring or included in the shielded cable (3 pairs). (2) terminal block for connection of the distributed power supply module. Schneider Electric 29 Parameter and protection settings Description E79438 Protection settings Trip Curve = inverse Threshold = 110 A Delay = 100 ms E65568 Example of advanced UMI with standard assignment of signal lamps. The Sepam 1000+ can be set: # via the front panel when Sepam 1000+ is equipped with the advanced UMI function. Function keys (blue) may be used to navigate in the menu and to scroll and accept the displayed values. Main functions performed: 5 changing of passwords 5 entry of general settings 5 entry of protection settings # via a PC equipped with the SFT 2841 software tool connected to the front panel for all types of Sepam 1000+. Menus guide the user through the different phases of parameter and protection setting by a series of windows suited to each operation. The SFT 2841 software tool may be used for Sepam 1000+ parameter and protection setting in connected or unconnected mode. The unconnected mode allows all the parameter settings to be prepared ahead of time and loaded in a single operation when the Sepam 1000+ is connected on site (downloading). Main functions performed by the SFT 2841: # changing of passwords # entry of general settings (ratings, integration period, …) # entry of protection settings # changing of program logic assignments # enabling/disabling of file saving functions. Example of phase overcurrent protection setting screen (series 20). E65575 Program logic parameter setting Program logic parameter setting consists mainly of assigning the data transmitted by the protection functions to the signal lamps and output relays. This is done by entering the data in the "control matrix" of the SFT 2841 software tool. Example of parameter setting (serieS 20). 30 Schneider Electric Program logic Parameter and protection settings Each Sepam 1000+ has program logic by default according to the chosen type (S20, S40, T20,…) as well as messages for the different signal lamps. The functions are assigned according to the most frequent use of the unit. The parameter setting and/or marking may be customized if required using the SFT 2841 software tool. Example of parameter setting: Sepam S20 equipped with the optional MES114 module IS (2) Outputs Functions Phase protection 01 # # # # # 02 # # # # # 50/51-1 50/51-2 Earth fault protection 50N/51N-1 50N/51N-2 Unbalance protection 46 Recloser 79 Open position l11 Closed position l12 Receive blocking l13 input l14 Line disconnector position open (1) Tripping by external l21 protection l22 l23 l24 Inhibit remote control l25 SF6 pressure drop l26 Transmit blocking # # # # # # # # # "Pick-up" signal # Watchdog Output O1 - tripping O2 - inhibit closing O3 - transmit BI O4 - watchdog O11 - close order O12 - phase fault indication O13 - earth fault indication O14 - permanent fault # Signal lamps L1 - I > 51 L2 - I >> 51 L3 - lo > 51N L4 - lo >> 51N L5 - ext L6 L7 - off L8 - on L9 - Trip Signal lamps 03 04 011 012 # # 013 014 L1 # L2 L3 Associated functions L4 L5 L6 L7 L8 # # # # # L9 # # # # # Circuit breaker control # # # Trip circuit supervision Logic discrimination # # # # # # Remote control # # Logic discrimination Disturbance recording triggering # (1) or disconnected position. (2) in service. Schneider Electric 31 Size and weight Characteristics Sepam 1000+ base unit Front panel flush-mounting Side view Cutout 176 160 ±0,2 E54752 mounting latch E54751 E54753 Top view 160 222 198 202 ±0,2 Mounting shown with advanced UMI and optional MES114 module. Weight series 20 = 1.2 kg without option. 1.7 kg with option. Weight series 40 = 1.4 kg without option. 1.9 kg with option. 98 6,5 E57704 “Terminal block” mounting with AMT840 plate Used to mount the Sepam at the back of the compartment with access to the connectors on the rear panel. Mounting associated with the use of the remote advanced UMI (DSM303). Mounting sheet thickness < 3 mm. 31 40 40 230 40 40 40 15 216 236 176 123 32 98 Schneider Electric Size and weight DSM303 module Cutout dimensions for flush-mounting (mounting plate thickness < 3 mm) # weight: 0.3 kg Side view Cutout 144 ±0,2 mounting latch E54756 E61212 Characteristics bent connector 7 11 96 117 15 maximum depth with CCA77x connection cord : 25 2 16 98.5 ±0,5 25 # weight: 0.25 kg # mounted on symmetrical DIN rail E69528 ACE959 module # weight: 0.1 kg # mounted on symmetrical DIN rail E61216 ACE949-2 module 4 14 88 88 72 30 (1 ) 30 (1) # weight: 0.2 kg # mounted on symmetrical DIN rail 4 E61225 MSA141 module # weight: 0.2 kg # mounted on symmetrical DIN rail E54757 MET148 module 4 14 14 88 88 30 ( 1) 30 ( 1) (1) depth with CCA77x connection cord: 70 mm. Schneider Electric 33 Characteristics Electrical characteristics Electrical characteristics Analog inputs Current transformer 1 A or 5 A CT (with CCA630) 1 A to 6250 A ratings input impedance consumption Voltage transformer 220 V to 250 kV ratings permanent thermal withstand 1 second overload input impedance input voltage permanent thermal withstand 1 second overload < 0.001 Ω < 0.001 VA at 1 A < 0.025 VA at 5 A 3 In 100 In > 100 kΩ 100 to 230/√3 V 230 V 480 V Temperature sensor input Type of temperature sensor Pt 100 Ni 100 / 120 Isolation from earth no no Current injected in sensor 4 mA 4 mA Logic inputs Voltage 24 to 250 Vcc -20/+10 % Consumption 3 mA typical Switching threshold (2) 14V typical Control output relays (O1, O2, O11 contacts) Voltage DC 24 / 48 V DC 127 V DC AC (47.5 to 63 Hz) Continuous current 8A 8A Breaking resistive load 8/4A 0.7 A capacity L/R load < 20 ms 6/2A 0.5 A L/R load < 40 ms 4/1A 0.2 A resistive load load p.f. > 0.3 Making < 15 A for 200 ms capacity Indication relay outputs (O3, O4, O12, O13, O14 contacts) Voltage DC 24 / 48 V DC 127 V DC AC (47.5 to 63 Hz) Continuous current 2A 2A Breaking L/R load < 20ms 2/1A 0.5 A capacity load p.f. > 0.3 Power supply (series 20) max. cons. (1) range deactivated cons. (1) 24 V DC -20 % +50 % (19,2 to 36 V DC) 3 to 6 W 7 to 11 W 48 / 250 V DC -20 % +10 % 2 to 4,5 W 6 to 8 W 110 / 240 V AC -20 % +10 % 3 to 9 VA 9 to 15 VA 47.5 to 63 Hz brownout withstand 10 ms Power supply (series 40) range deactivated cons. (1) max. cons. (1) 24 / 250 V DC -20 % +10 % 3 to 6 W 7 to 11 W 110 / 240 V AC -20 % +10 % 3 to 6 W 9 to 25 W 47.5 to 63 Hz brownout withstand 20 ms Analog output Current 4 - 20 mA, 0 - 20 mA, 0 - 10 mA Load impedance < 600 Ω (wiring included) Accuracy 0.50 % (from 19.2 to 275 Vcc) 220 V DC 8A 0.3 A 0.2 A 0.1 A 100 to 240 V AC 8A 8A 5A 220 V DC 2A 0.15 A 100 to 240 V AC 2A 1A inrush current < 10 A for 10 ms < 10 A for 10 ms < 15 A for first half-period inrush current < 28 A 100 µs < 28 A 100 µs (1) according to configuration. (2) for upper values, please consult us. 34 Schneider Electric Environmental characteristics Characteristics Isolation Dielectric withstand at power frequency 1.2 / 50 µs impulse wave Electromagnetic compatibility Fast transient bursts 2 kVrms - 1mn (1) 5 kV (2) CEI 60255-5 CEI 60255-5 CEI 60255-22-4 CEI 61000-4-4 CEI 60255-22-1 CEI 61000-4-3 CEI 61000-4-6 CEI 60255-22-2 CEI 61000-4-2 EN 55022 / CISPR 22 EN 55022 / CISPR 22 class IV level IV class III level III level III class III level III class B class A CEI 60529 IP 52 (7) Vibrations Shocks / jolts Earthquakes Fire resistance Climatic withstand Operation Storage Damp heat CEI 60255-21-1 CEI 60255-21-2 CEI 60255-21-3 CEI 60695-2-1 class II (5) class II (5) class II (5) glow wire Effect of corrosion Certification CE UL508 (6) CEI-68054-4 1 MHz damped oscillating wave Immunity to radiated fields Immunity to conducted RF disturbances Electrostatic discharge Conducted disturbance emission Disturbing field emission Mechanical robustness Degree of protection CEI 60068-2-1 et 2 CEI 60068-2-1 et 2 CEI 60068-2-3 10 V/m 10 V 6 kV / 8 kV (contact / air) on aux. supply (3) (4) on front panel other sides closed (except for rear IP 20) 650 °C -25 °C à + 70 °C -25 °C à +70 °C 93 % HR à 40 °C, 56 days (storage) 10 days (operation) class I (1) except for communication 1 kVrms. (2) except for communication 3 kV common mode, 1 kV differential mode. (3) generic EN 50081-1 standard. (4) generic EN 50081-2 standard. (5) intrinsic withstand of product, excluding support equipment. (6) series 40: please consult us. (7) a gasket delivered with the product can be used to ensure NEMA12 withstand. Schneider Electric 35 Notes 36 Schneider Electric Ordering information To make it easier to choose and fill in your order form, you may use the Schneider Electric Sepam 1000+ electronic catalogue (please consult us) or include this page with your order, filling in the requested quantities in the spaces and ticking off the boxes to indicate your choices. Sepam 1000+ Type of application Series 20 Sensors S20 (59620) T20 (59621) M20 (59622) TC 1A / 5A CCA630 LPCT CCA670 B21 (59624) B22 (59625) S40 (59680) S41 (59681) S42 (2) (59682) T40 (2) (59683) T42 (2) (59684) M41(2) (59685) (59630) Characteristics common to the order (1) IHM / Power supply Working languages Connectors Standard UMI Screw-on connector (59602) 48-250V (59603) (59631) (59609) English / Spanish Advanced UMI 24V TP CCT640 English / French 24V (59632) 48-250V (59611) CCA620 (59668) Ring terminal CCA622 (59669) (59606) (59607) Series 40 TC 1A / 5A CCA630 Standard UMI (59630) 24-250V English / French (59600) (59615) LPCT CCA670 (59631) Advanced UMI 24-250V Screw-on connector CCA620 (59668) CCA626 (59656) English / Spanish (59604) (59616) Ring terminal CCA622 (59669) CCA627 (59657) (1) only one choice per characteristic (UMI, working language, …). (2) available in 2002. Separate modules and optionals accessories Description Reference residual current sensors (ø 120) ................................................................................ CSH120 Item number residual current sensors (ø 200) ................................................................................ CSH200 59635 59636 interposing ring CT for residual current input ............................................................. CSH30 59634 core balance CT interface .......................................................................................... ACE990 59672 59645 59646 59640 59647 59608 59670 59642 59643 59663 59660 59661 59662 59671 59648 59649 59650 59674 59675 59677 59678 4 input + 4 output module ........................................................................................... MES108 10 input + 4 output module ......................................................................................... MES114 8 temperature sensor module .................................................................................... MET148 analog output module ................................................................................................. MSA141 remote advanced UMI module (1) ................................................................................ DSM303 mounting frame .......................................................................................................... AMT840 2-wire RS 485 network interface ................................................................................ ACE949-2 4-wire RS 485 network interface ................................................................................ ACE959 communication cable L = 3 m .................................................................................... CCA612 remote module connection cable L = 0.6 m ............................................................... CCA770 remote module connection cable L = 2 m ................................................................. CCA772 remote module connection cable L = 4 m .................................................................. CCA774 PC parameter setting and operation software kit (2) .................................................... kit SFT2841 RS 485 / RS 232 converter ........................................................................................ ACE909-2 RS 485 / RS 485 interface (AC) ................................................................................. ACE919CA RS 485 / RS 485 interface (DC) ................................................................................. ACE919CC Sepam 1000+ series 20 instruction manual ................. French ................................. PCRED301005FR Sepam 1000+ series 20 instruction manual ................. English ................................ PCRED301005EN Sepam 1000+ series 40 instruction manual French .... French ................................. PCRED301006FR Sepam 1000+ series 20 instruction manual English ... English ................................ PCRED301006EN (1) not compatible with Sepam units equipped with integrated advanced UMI. (2) including the CCA612 connection cord. Schneider Electric Industries SA F - 38050 Grenoble cedex 9 Tel : +33 (0)4 76 57 60 60 Telex : merge 320842 F http:/www.schneider-electric.com PCRED301004EN ART.08535 As standards, specifications and designs change from time to time, please ask for confirmation of the information given in this document. This document has been printed on ecological paper. Publishing : Schneider Electric Production : Schneider Electric Printing : Imprimerie des 2 ponts PCRED301004EN- © 2001 Schneider Electric - All wrights reserved Quantity